Enable KCS interface in zaius

[Zheng Bao]

I use qemu to test the image. Got the result.

$ qemu-system-arm -m 512 -M ast2500-evb -nographic  -drive file=phosphor-intel-platform-1.bin,format=raw,if=mtd


U-Boot 2016.07 (Sep 11 2019 - 21:38:56 +0000)

SOC : AST2500-A1
RST : 0x01
PLL :     24 MHz
CPU :    792 MHz
MEM :   2.240 MHz, EEC: Disable, Cache: Disable
VGA :    16 MiB
DRAM :   init by SOC
       Watchdog enabled
DRAM:  496 MiB
Flash: 32 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Error: start and/or end address not on sector boundary
Error: start and/or end address not on sector boundary
Error: start and/or end address not on sector boundary


Zheng
________________________________
From: Yong Li <yong.b.li at linux.intel.com>
Sent: Tuesday, September 10, 2019 1:26 AM
To: 'Zheng Bao' <fishbaoz at hotmail.com>; 'Andrew Jeffery' <andrew at aj.id.au>; 'AKASH G J' <akashgj91 at gmail.com>; openbmc at lists.ozlabs.org <openbmc at lists.ozlabs.org>
Subject: RE: Enable KCS interface in zaius


I would like to know how did you perform the build? Please perform the below commands:



export TEMPLATECONF=meta-openbmc-mods/meta-wht/conf

source oe-init-build-env

bitbake intel-platforms



Thanks,

Yong



From: Zheng Bao <fishbaoz at hotmail.com>
Sent: Saturday, September 7, 2019 7:34 PM
To: Yong Li <yong.b.li at linux.intel.com>; 'Andrew Jeffery' <andrew at aj.id.au>; 'AKASH G J' <akashgj91 at gmail.com>; openbmc at lists.ozlabs.org
Subject: Re: Enable KCS interface in zaius



I check out the https://github.com/Intel-BMC/openbmc

and build the board: meta-openbmc-mods/meta-wolfpass/conf



But got the error,

dd: failed to open '/home/baozheng/bmc/openbmc-github/build/tmp/deploy/images/intel-ast2500/fitImage-rootfs-intel-ast2500.bin': No such file or directory



Did I miss something?



Zheng





________________________________

From: openbmc <openbmc-bounces+fishbaoz=hotmail.com at lists.ozlabs.org<mailto:openbmc-bounces+fishbaoz=hotmail.com at lists.ozlabs.org>> on behalf of Yong Li <yong.b.li at linux.intel.com<mailto:yong.b.li at linux.intel.com>>
Sent: Friday, August 30, 2019 6:29 AM
To: 'Andrew Jeffery' <andrew at aj.id.au<mailto:andrew at aj.id.au>>; 'AKASH G J' <akashgj91 at gmail.com<mailto:akashgj91 at gmail.com>>; openbmc at lists.ozlabs.org<mailto:openbmc at lists.ozlabs.org> <openbmc at lists.ozlabs.org<mailto:openbmc at lists.ozlabs.org>>
Subject: RE: Enable KCS interface in zaius



It seems that the kernel needs to enable KCS, and disable BT.
CONFIG_ASPEED_KCS_IPMI_BMC=y

Suggest to check on this: https://github.com/Intel-BMC/openbmc

Thanks,
Yong
-----Original Message-----
From: openbmc <openbmc-bounces+yong.b.li=linux.intel.com at lists.ozlabs.org<mailto:openbmc-bounces+yong.b.li=linux.intel.com at lists.ozlabs.org>>
On Behalf Of Andrew Jeffery
Sent: Friday, August 30, 2019 12:42 PM
To: AKASH G J <akashgj91 at gmail.com<mailto:akashgj91 at gmail.com>>; openbmc at lists.ozlabs.org<mailto:openbmc at lists.ozlabs.org>
Subject: Re: Enable KCS interface in zaius



On Thu, 29 Aug 2019, at 09:05, AKASH G J wrote:
> Hi all,
>
> I am using server platform with Intel processor and Aspeed AST-2500
> BMC. OpenBMC firmware with zaius configuration is used for BMC.
>

Zaius is an OpenPOWER platform (and our OpenPOWER platforms use the BT
interface rather than KCS). You're using an Intel-based processor for the
host, so perhaps it's better to start with an x86-based platform such as the
s2600wf. This should already have KCS IPMI enabled for you.

Andrew
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/openbmc/attachments/20190912/4b67d366/attachment.htm>