booting 2.6 kernel on ML403

[Pradeep Sampath]

Hello Ameet/Ming,
   
  First of all really appreciate your inputs on this... 
  Problem 1 :
  I was using the factory shipped compact flash as is which comes with a DOS FAT16 partition and a linux 83 partition with ext3 filesystem. I tried it on 2 factory shipped CFs and its the same behavior - . When i plug-in the CF card reader to the linux box it always reads it as "sda" and in the linux2.6.17.1/Documentation/devices.txt - sda is the device file for SCSI disk devices. Wonerding how you guys configured the root option as "/dev/xsa".
   
  Now i re-formatted my CF, created a ext2 filesystem using busybox-1.1.0 like the BYU instructions. Created 2 partitions on CF card 1. FAT16 partition & 2. linux partition and then created 1. dos file system using mkdosfs and 2. linux ext2 filesystem using mke2fs.
   
  But the problem still persists and i get "Please append a correct "root=" boot option :"
  :(
   
  Problem 2: After i included the TEMAC driver and sysace drivers, the kernel just hangs. I thought i'll fix problem 1 before i get to problem 2... 
   
  With your help i am getting the confidence that i can make this all work!
  thanks once again.
  -Pradeep



Ming Liu <eemingliu at hotmail.com> wrote:
  Hello Ameet,
I am using that driver very well now. There is only one problem. It seems 
that the driver for TEMAC only support Gigabit Enet, not 10/100/1000M 
adapted. But because I want to use the Gigabit enet, I don't care that. So 
it's OK, at lease for 1Gbit/s.

So I don't think Pradeep's problem is caused by Temac. I still suspect that 
he didn't pass a right parameter to "root=", just like what I posted 
before.

Regards
Ming


>From: Ameet Patil 
>To: Ming Liu 
>CC: pradeepsampath at yahoo.com, linuxppc-embedded at ozlabs.org
>Subject: Re: booting 2.6 kernel on ML403
>Date: Wed, 04 Oct 2006 09:35:07 +0100
>
>Ming Liu wrote:
> > Hi,
> >
> >> [ 3.093694] TCP bic registered
> >> [ 3.129458] NET: Registered protocol family 8
> >> [ 3.181412] NET: Registered protocol family 20
> >> [ 3.236744] VFS: Cannot open root device "xsa2" or unknown-block(0,0)
> >> [ 3.313092] Please append a correct "root=" boot option
> >
> > It looks that some errors still exist in the parameters you passed to
> > "root=". Please double check it, or post it in the maillist for deep
> > analysis.
> > Regards
> > Ming
> >
> > _________________________________________________________________
> > ÏíÓÃÊÀ½çÉÏ×î´óµÄµç×ÓÓʼþϵͳ¡ª MSN Hotmail¡£ http://www.hotmail.com
> > 
------------------------------------------------------------------------
> >
> > _______________________________________________
> > Linuxppc-embedded mailing list
> > Linuxppc-embedded at ozlabs.org
> > https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>Hi Ming,
>IIRC, you are or were using the TEMAC driver along with my System Ace
>driver, isn't it? Does my driver patch ***-after-TEMAC.patch work for
>you? I ask this because Pradeep is having some problems using it (see
>Problem 2 in his email). Could you please update on this?
>
>Thanks,
>-Ameet

_________________________________________________________________
ÓëÁª»úµÄÅóÓѽøÐн»Á÷£¬ÇëʹÓà MSN Messenger: http://messenger.msn.com/cn 

_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded at ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20061004/46287a4d/attachment.htm