3Com 574BT PCMCIA Card on PowerPC

[Magnus Damm]

Make sure that the socket driver is configured correctly for
your board. Voltage control pins and stuff like that are
board-specific.

I would first try a PCMCIA card that is known to work easily
right out of the box. Maybe the wireless board.

Then you could verify the 3Com card.
Scan the source-code for the 3Com card and see if it's endian-aware.

/ magnus

On Fri, 31 Jan 2003 13:04:38 +0100 (MET)
Andreas Plaickner <apxx at gmx.net> wrote:

>
> Hello,
>
> I am new to the development of RTAI Linux on
> PowerPC boards, therefore I would be very
> grateful for some advice.
>
> I want to use the PCMCIA card 3Com
> 3CCFE574BT in the pcmcia-slot on the board. On the
> board is a Motorola MPC855T.
>
> I have seen that there exists already a solution
> for a wireless LAN card. I took these steps as
> a basis to try to bring to work my card. On my
> board it is not possible to start the card
> services with the script
> /etc/rc.d/rc.pcmcia start
> as there is no bash to interpret the script, there
> is only a BusyBox.
>
> S I start the PCMCIA card services manually:
> insmod pcmcia_core.o
> insmod m8xx_pcmcia.o
> insmod ds.o
> insmod 3c574_cs.o
>
> When I don't insert the card in the slot and I only
> start the cardmgr everything seems to be fine,
> the cardmgr responds with:
>
> cardmgr[61]: watching 1 sockets
> cardmgr[62]: starting, version is 3.2.0
>
> When I insert the card, nothing happens so I have
> to call the command
> cardctl insert
>
> When I do this one I get the following error message,
> and the system reboots:
>
> / # Oops: Kernel Mode Software FPU Emulation, sig: 8
> NIP: 00000304 XER: A000007F LR: C3040490 SP: C07F1810 REGS: c07f1760 TRAP:
> 1000
> MSR: 00001000 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 00
> TASK = c07f0000[58] 'cardmgr' Last syscall: 54
> last math 00000000 last altivec 00000000
> GPR00: 00000800 C07F1810 C07F0000 0000001F 00100000 00000002 C07F17AB
> 00000000
> GPR08: 0000000F 0000030E 00000058 C000B2D4 95743B34 018223F8 00FF3D00
> 007FFF5D
> GPR16: 00000000 00000001 007FFF00 FFFFFFFF 00009032 007F1E80 C07F19B8
> C07F1838
> GPR24: C093D0FC C093D000 C093D08C C0941170 0000002B C093D1BC 00000300
> C093D000
> Call backtrace:
> C3040490 C304098C C3030208 C3031880 C3040244 C303C894 C303D614
> C004377C C00025BC 01802D18 01803444 01804A20 016D9DBC 00000000
>
> When I, after inserting the modules, dont start the cardmgr,
> but write cardctl insert I can check with the commands
>
> cardctl status
> cardctl config
> cardctl ident
>
> and get some information that the card is in the socket.
> But I think this one doesn't help as I need to start the
> cardmgr to use the card. When I start the cardmgr now
> I get again the above errormessage.
>
> What I also tried is to change the file config.opts,
> setting the memory area to 0xe0000000-0xec000000
> because when I start the board during the boot
> process appears
> PCMCIA slot B: phys mem e0000000...ec000000 (size 0c000000)
>
> When I did this one I got the following error-msg:
>
> /lib/modules/2.4.4-rthal5/pcmcia # cardmgr
> cardmgr[61]: watching 1 sockets
> cardmgr[62]: starting, version is 3.2.0
> /lib/modules/2.4.4-rthal5/pcmcia # cardctl insert
> /lib/modules/2.4.4-rthal5/pcmcia # __ioremap(): phys addr 0 is RAM lr
> c000b25c
> Oops: kernel access of bad area, sig: 11
> NIP: CF032C34 XER: A000007E LR: CF032C10 SP: C09AF8F0 REGS: c09af840 TRAP:
> 0300
> MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
> DAR: 00000000, DSISR: 00000405
> TASK = c09ae000[62] 'cardmgr' Last syscall: 54
> last math 00000000 last altivec 00000000
> ....
>
>
> My Kernel-Image is
>
> ## Booting image at 40040000 ...
>    Image Name:   Linux-2.4.4
>    Created:      2002-07-17  10:40:49 UTC
>    Image Type:   PowerPC Linux Kernel Image (gzip compressed)
>    Data Size:    614209 Bytes = 599 kB = 0 MB
>    Load Address: 00000000
>    Entry Point:  00000000
>    Verifying Checksum ... OK
>    Uncompressing Kernel Image ... OK
>
> I didn't create a new kernel, but I used one that was already
> pre-installed on the board. Could this one be the reason
> for the above error?
>
> I am stuck and don't know how to continue, therefore I
> would be very grateful if someone could give me some advice.
>
> Thanks very much in advance.
>
> Andreas
>
> --
> +++ GMX - Mail, Messaging & more  http://www.gmx.net +++
> NEU: Mit GMX ins Internet. Rund um die Uhr für 1 ct/ Min. surfen!
>
>
>

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/