[PATCH 08/23] spi/atmel: add DT support
Richard Genoud
richard.genoud at gmail.com
Tue Aug 14 23:49:22 EST 2012
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
The atmel_spi use only gpio for chip select.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
Cc: devicetree-discuss at lists.ozlabs.org
Cc: spi-devel-general at lists.sourceforge.net
---
.../devicetree/bindings/spi/spi_atmel.txt | 6 +++++
drivers/spi/spi-atmel.c | 21 ++++++++++++++++---
2 files changed, 23 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/spi_atmel.txt
diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt
new file mode 100644
index 0000000..7ec3d8d
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt
@@ -0,0 +1,6 @@
+Atmel SPI device
+
+Required properties:
+- compatible : should be "atmel,at91rm9200-spi".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain macb interrupt
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 70f7bfa..ad47b6d 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -19,6 +19,7 @@
#include <linux/interrupt.h>
#include <linux/spi/spi.h>
#include <linux/slab.h>
+#include <linux/of.h>
#include <asm/io.h>
#include <mach/board.h>
@@ -711,7 +712,7 @@ static int atmel_spi_setup(struct spi_device *spi)
u32 scbr, csr;
unsigned int bits = spi->bits_per_word;
unsigned long bus_hz;
- unsigned int npcs_pin;
+ int npcs_pin;
int ret;
as = spi_master_get_devdata(spi->master);
@@ -783,7 +784,9 @@ static int atmel_spi_setup(struct spi_device *spi)
csr |= SPI_BF(DLYBCT, 0);
/* chipselect must have been muxed as GPIO (e.g. in board setup) */
- npcs_pin = (unsigned int)spi->controller_data;
+ if (!gpio_is_valid(spi->cs_gpio))
+ spi->cs_gpio = (int)spi->controller_data;
+ npcs_pin = spi->cs_gpio;
asd = spi->controller_state;
if (!asd) {
asd = kzalloc(sizeof(struct atmel_spi_device), GFP_KERNEL);
@@ -900,7 +903,7 @@ static void atmel_spi_cleanup(struct spi_device *spi)
{
struct atmel_spi *as = spi_master_get_devdata(spi->master);
struct atmel_spi_device *asd = spi->controller_state;
- unsigned gpio = (unsigned) spi->controller_data;
+ unsigned gpio = spi->cs_gpio;
if (!asd)
return;
@@ -950,7 +953,8 @@ static int __devinit atmel_spi_probe(struct platform_device *pdev)
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->bus_num = pdev->id;
- master->num_chipselect = 4;
+ master->dev.of_node = pdev->dev.of_node;
+ master->num_chipselect = master->dev.of_node ? 0 : 4;
master->setup = atmel_spi_setup;
master->transfer = atmel_spi_transfer;
master->cleanup = atmel_spi_cleanup;
@@ -1079,11 +1083,20 @@ static int atmel_spi_resume(struct platform_device *pdev)
#define atmel_spi_resume NULL
#endif
+#if defined(CONFIG_OF)
+static const struct of_device_id atmel_spi_dt_ids[] = {
+ { .compatible = "atmel,at91rm9200-spi" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_spi_dt_ids);
+#endif
static struct platform_driver atmel_spi_driver = {
.driver = {
.name = "atmel_spi",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_spi_dt_ids),
},
.suspend = atmel_spi_suspend,
.resume = atmel_spi_resume,
--
1.7.2.5
More information about the devicetree-discuss
mailing list