[PATCH v3 00/10] ARM: tegra: Add PCIe device tree support

Tue Aug 14 07:38:45 EST 2012

On 08/13/2012 03:33 PM, Thierry Reding wrote:
> On Mon, Aug 13, 2012 at 12:47:38PM -0600, Stephen Warren wrote:
>> On 08/13/2012 11:40 AM, Thierry Reding wrote:
>>> On Mon, Aug 06, 2012 at 01:42:21PM -0600, Stephen Warren wrote:
>>>> On 07/26/2012 01:55 PM, Thierry Reding wrote:
>>>>> This patch series adds support for device tree based probing of
>>>>> the PCIe controller found on Tegra SoCs.
>>>>
>>>> Thierry, I just tested all Tegra boards in v3.6-rc1, and noticed
>>>> that PCIe doesn't work on TrimSlice when booting use device tree.
>>>> I think I found the cause, and I can't see why the same problem
>>>> doesn't affect this series. Perhaps you can enlighten me?
>> ...
>>>> PCI: Device 0000:01:00.0 not available because of resource
>>>> collisions
>> ...
>>> I've looked into this a bit, and it seems like ARM is using an
>>> open- coded version of the pci_enable_resources() function here,
>>> with the only difference being the unconditional enabling of both
>>> I/O and memory- mapped access for bridges. On Tegra there is
>>> already a PCI fixup to do this, so pci_enable_resources() can be
>>> used as-is. I came up with the attached patch but haven't been able
>>> to test it yet.
>>
>> Thanks very much for looking into this.
>>
>> The patch did alter the behavior a little for TrimSlice, but didn't
>> solve the problem. The old error messages:
>>
>>> [    2.173971] PCI: Device 0000:01:00.0 not available because of resource collisions
>>> [    2.181453] r8169 0000:01:00.0: (unregistered net_device): enable failure
>>> [    2.188254] r8169: probe of 0000:01:00.0 failed with error -22
>>
>> Were replaced with the following with your patch:
>>
>>> [    2.174010] r8169 0000:01:00.0: device not available (can't reserve [io  0x0000-0x00ff])
>>> [    2.182098] r8169 0000:01:00.0: (unregistered net_device): enable failure
>>> [    2.188900] r8169: probe of 0000:01:00.0 failed with error -22
>>
>> This message appears from drivers/pci/setup-res.c pci_enable_resources()
>> due to:
>>
>>> 		if (!r->parent) {
>>> 			dev_err(&dev->dev, "device not available "
>>> 				"(can't reserve %pR)\n", r);
>>> 			return -EINVAL;
>>> 		}
> 
> Looking at the code some more, this may be caused by the pci_remap_io()
> patch series, so you might want to revert that patch and see if it fixes
> the I/O resources.
> 

Humm... But this patch deals with the i/o space and it is failing below
on the memory space.

>> That check doesn't appear in ARM's custom pcibios_enable_device().
>> Disabling that check yields:
>>
>>> [    2.174192] r8169 0000:01:00.0: enabling device (0140 -> 0143)
>>> [    2.180041] r8169 0000:01:00.0: BAR 2: can't reserve [mem 0x00000000-0x00000fff 64bit pref]
>>> [    2.188386] r8169 0000:01:00.0: (unregistered net_device): could not request regions
>>> [    2.196140] r8169: probe of 0000:01:00.0 failed with error -16
>>
>> I think that's because the pci_dev's resources are initially assigned
>> PCI-aperture-relative addresses, and then these are later patched up to
>> take account of where the aperture is mapped into the CPU's address space.
>>
>> Boot log using board files:
>>
>>> [    1.146145] pci 0000:01:00.0: reg 10: [io  0x0000-0x00ff]
>>> [    1.151745] pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00000fff 64bit pref]
>>> [    1.159007] pci 0000:01:00.0: reg 20: [mem 0x00000000-0x00003fff 64bit pref]
>>> [    1.166270] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
>> ...
>>> [    1.217829] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
>>> [    1.225264] pci 0000:01:00.0: BAR 4: assigned [mem 0xa0020000-0xa0023fff 64bit pref]
>>> [    1.233236] pci 0000:01:00.0: BAR 2: assigned [mem 0xa0024000-0xa0024fff 64bit pref]
>>> [    1.241206] pci 0000:01:00.0: BAR 0: assigned [io  0x1000-0x10ff]
>> ... (I added some extra printks:)
>>> [    1.488007] r8169 0000:01:00.0: BAR 0: requesting [io  0x1000-0x10ff]
>>> [    1.501483] r8169 0000:01:00.0: BAR 2: requesting [mem 0xa0024000-0xa0024fff 64bit pref]
>>> [    1.516611] r8169 0000:01:00.0: BAR 4: requesting [mem 0xa0020000-0xa0023fff 64bit pref]
>>
>> whereas for a device tree boot:
>>
>> (same):
>>> [    2.112217] pci 0000:01:00.0: reg 10: [io  0x0000-0x00ff]
>>> [    2.117635] pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00000fff 64bit pref]
>>> [    2.124690] pci 0000:01:00.0: reg 20: [mem 0x00000000-0x00003fff 64bit pref]
>>> [    2.131731] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
>> ... (request region happens early)
>>> [    2.179838] r8169 0000:01:00.0: BAR 0: requesting [io  0x0000-0x00ff]
>>> [    2.193312] r8169 0000:01:00.0: BAR 2: requesting [mem 0x00000000-0x00000fff 64bit pref]
>>> [    2.201397] r8169 0000:01:00.0: BAR 2: can't reserve [mem 0x00000000-0x00000fff 64bit pref]
>>> [    2.209742] r8169 0000:01:00.0: (unregistered net_device): could not request regions
>> ... (same, just happens too late)
>>> [    2.236818] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0000000-0xa001ffff pref]
>>> [    2.244027] pci 0000:01:00.0: BAR 4: assigned [mem 0xa0020000-0xa0023fff 64bit pref]
>>> [    2.251794] pci 0000:01:00.0: BAR 2: assigned [mem 0xa0024000-0xa0024fff 64bit pref]
>>> [    2.259542] pci 0000:01:00.0: BAR 0: assigned [io  0x1000-0x10ff]
>>
>> I suspect this is all still related to the PCI devices themselves being
>> probed much earlier in the overall PCI initialization sequence when the
>> PCI controller is probed later in the boot sequence, whereas PCI device
>> probe is deferred until the overall PCI initialization sequence is
>> complete if the PCI controller is probed very early in the boot sequence.
>>
>> Does anyone know where/what that "probe now" vs. "probe later" decision
>> point is? I'll try and track it down if nobody beats me to it.
> 
> There's the io_offset and mem_offset fields that I've completely ignored
> up to now. Can you try the patch below to see if it changes anything?
> I'm sorry but I can't test any of this myself right now.

Arnd and I discussed io_offset some. I don't think either of us can
figure out when it should be anything but 0 at least if pci i/o bus
addresses start at 0.

I don't think mem_offset is the issue. I think perhaps you need to set
pcibios_min_mem to the memory window base (0xa0000000), but that's just
a guess.

Rob

> 
> Thierry
> 
> 
> 
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/devicetree-discuss
> 