[PATCH v3 09/11] i2c: npcm: Handle spurious interrupts

Avi Fishman avifishman70 at gmail.com
Tue Apr 5 03:03:44 AEST 2022


On Thu, Mar 3, 2022 at 4:14 PM Andy Shevchenko
<andriy.shevchenko at linux.intel.com> wrote:
>
> On Thu, Mar 03, 2022 at 02:48:20PM +0200, Tali Perry wrote:
> > > On Thu, Mar 3, 2022 at 12:37 PM Andy Shevchenko <andriy.shevchenko at linux.intel.com> wrote:
> > > >
> > > > On Thu, Mar 03, 2022 at 04:31:39PM +0800, Tyrone Ting wrote:
> > > > > From: Tali Perry <tali.perry1 at gmail.com>
> > > > >
> > > > > In order to better handle spurious interrupts:
> > > > > 1. Disable incoming interrupts in master only mode.
> > > > > 2. Clear end of busy (EOB) after every interrupt.
> > > > > 3. Return correct status during interrupt.
> > > >
> > > > This is bad commit message, it doesn't explain "why" you are doing these.
>
> ...
>
> > BMC users connect a huge tree of i2c devices and muxes.
> > This tree suffers from spikes, noise and double clocks.
> > All these may cause spurious interrupts to the BMC.
> >
> > If the driver gets an IRQ which was not expected and was not handled
> > by the IRQ handler,
> > there is nothing left to do but to clear the interrupt and move on.
>
> Yes, the problem is what "move on" means in your case.
> If you get a spurious interrupts there are possibilities what's wrong:
> 1) HW bug(s)
> 2) FW bug(s)
> 3) Missed IRQ mask in the driver
> 4) Improper IRQ mask in the driver
>
> The below approach seems incorrect to me.
>

Andy, What about this explanation:
On rare cases the i2c gets a spurious interrupt which means that we
enter an interrupt but in
the interrupt handler we don't find any status bit that points to the
reason we got this interrupt.
This may be a rare case of HW issue that is still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is
not enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the transaction.
On next xmit transaction if the bus is still busy the master will
issue a recovery process before issuing the new transaction.
> > If the transaction failed, driver has a recovery function.
> > After that, user may retry to send the message.
> >
> > Indeed the commit message doesn't explain all this.
> > We will fix and add to the next patchset.
> >
> > > > > +     /*
> > > > > +      * if irq is not one of the above, make sure EOB is disabled and all
> > > > > +      * status bits are cleared.
> > > >
> > > > This does not explain why you hide the spurious interrupt.
> > > >
> > > > > +      */
> > > > > +     if (ret == IRQ_NONE) {
> > > > > +             npcm_i2c_eob_int(bus, false);
> > > > > +             npcm_i2c_clear_master_status(bus);
> > > > > +     }
> > > > > +
> > > > > +     return IRQ_HANDLED;
>
> --
> With Best Regards,
> Andy Shevchenko
>
>


-- 
Regards,
Avi


More information about the openbmc mailing list