[PATCH linux dev-5.3 v2 4/8] fsi: move defines to common header
Joel Stanley
joel at jms.id.au
Thu Oct 31 16:36:21 AEDT 2019
The FSI master registers are common to the hub and AST2600 master (and
the FSP2, if someone was to upstream a driver for that).
Add defines to the fsi-master.h header, and introduce headings to
delineate the existing low level details.
Signed-off-by: Joel Stanley <joel at jms.id.au>
---
drivers/fsi/fsi-master-aspeed.c | 55 -------------------------
drivers/fsi/fsi-master-hub.c | 46 ---------------------
drivers/fsi/fsi-master.h | 71 +++++++++++++++++++++++++++++++++
3 files changed, 71 insertions(+), 101 deletions(-)
diff --git a/drivers/fsi/fsi-master-aspeed.c b/drivers/fsi/fsi-master-aspeed.c
index 5b947c70c0f9..e38e1c2c4f15 100644
--- a/drivers/fsi/fsi-master-aspeed.c
+++ b/drivers/fsi/fsi-master-aspeed.c
@@ -17,61 +17,6 @@
#include "fsi-master.h"
-/* TODO: these are copied from the hub master. Put them in a common header */
-
-/* Control Registers */
-#define FSI_MMODE 0x0 /* R/W: mode */
-#define FSI_MDLYR 0x4 /* R/W: delay */
-#define FSI_MCRSP 0x8 /* R/W: clock rate */
-#define FSI_MENP0 0x10 /* R/W: enable */
-#define FSI_MLEVP0 0x18 /* R: plug detect */
-#define FSI_MSENP0 0x18 /* S: Set enable */
-#define FSI_MCENP0 0x20 /* C: Clear enable */
-#define FSI_MAEB 0x70 /* R: Error address */
-#define FSI_MVER 0x74 /* R: master version/type */
-#define FSI_MSTAP0 0xd0 /* R: Port status */
-#define FSI_MRESP0 0xd0 /* W: Port reset */
-#define FSI_MESRB0 0x1d0 /* R: Master error status */
-#define FSI_MRESB0 0x1d0 /* W: Reset bridge */
-#define FSI_MSCSB0 0x1d4 /* R: Master sub command stack */
-#define FSI_MATRB0 0x1d8 /* R: Master address trace */
-#define FSI_MDTRB0 0x1dc /* R: Master data trace */
-#define FSI_MECTRL 0x2e0 /* W: Error control */
-
-/* MMODE: Mode control */
-#define FSI_MMODE_EIP 0x80000000 /* Enable interrupt polling */
-#define FSI_MMODE_ECRC 0x40000000 /* Enable error recovery */
-#define FSI_MMODE_RELA 0x20000000 /* Enable relative address commands */
-#define FSI_MMODE_EPC 0x10000000 /* Enable parity checking */
-#define FSI_MMODE_P8_TO_LSB 0x00000010 /* Timeout value LSB */
- /* MSB=1, LSB=0 is 0.8 ms */
- /* MSB=0, LSB=1 is 0.9 ms */
-#define FSI_MMODE_CRS0SHFT 18 /* Clk rate selection 0 shift */
-#define FSI_MMODE_CRS0MASK 0x3ff /* Clk rate selection 0 mask */
-#define FSI_MMODE_CRS1SHFT 8 /* Clk rate selection 1 shift */
-#define FSI_MMODE_CRS1MASK 0x3ff /* Clk rate selection 1 mask */
-
-/* MRESB: Reset brindge */
-#define FSI_MRESB_RST_GEN 0x80000000 /* General reset */
-#define FSI_MRESB_RST_ERR 0x40000000 /* Error Reset */
-
-/* MRESB: Reset port */
-#define FSI_MRESP_RST_ALL_MASTER 0x20000000 /* Reset all FSI masters */
-#define FSI_MRESP_RST_ALL_LINK 0x10000000 /* Reset all FSI port contr. */
-#define FSI_MRESP_RST_MCR 0x08000000 /* Reset FSI master reg. */
-#define FSI_MRESP_RST_PYE 0x04000000 /* Reset FSI parity error */
-#define FSI_MRESP_RST_ALL 0xfc000000 /* Reset any error */
-
-/* MECTRL: Error control */
-#define FSI_MECTRL_EOAE 0x8000 /* Enable machine check when */
- /* master 0 in error */
-#define FSI_MECTRL_P8_AUTO_TERM 0x4000 /* Auto terminate */
-
-#define FSI_ENGID_HUB_MASTER 0x1c
-#define FSI_HUB_LINK_OFFSET 0x80000
-#define FSI_HUB_LINK_SIZE 0x80000
-#define FSI_HUB_MASTER_MAX_LINKS 8
-
#define FSI_LINK_ENABLE_SETUP_TIME 10 /* in mS */
#define FSI_NUM_DEBUGFS_ENTRIES 17
diff --git a/drivers/fsi/fsi-master-hub.c b/drivers/fsi/fsi-master-hub.c
index f158b1a88286..def35cf92571 100644
--- a/drivers/fsi/fsi-master-hub.c
+++ b/drivers/fsi/fsi-master-hub.c
@@ -13,53 +13,7 @@
#include "fsi-master.h"
-/* Control Registers */
-#define FSI_MMODE 0x0 /* R/W: mode */
-#define FSI_MDLYR 0x4 /* R/W: delay */
-#define FSI_MCRSP 0x8 /* R/W: clock rate */
-#define FSI_MENP0 0x10 /* R/W: enable */
-#define FSI_MLEVP0 0x18 /* R: plug detect */
-#define FSI_MSENP0 0x18 /* S: Set enable */
-#define FSI_MCENP0 0x20 /* C: Clear enable */
-#define FSI_MAEB 0x70 /* R: Error address */
-#define FSI_MVER 0x74 /* R: master version/type */
-#define FSI_MRESP0 0xd0 /* W: Port reset */
-#define FSI_MESRB0 0x1d0 /* R: Master error status */
-#define FSI_MRESB0 0x1d0 /* W: Reset bridge */
-#define FSI_MECTRL 0x2e0 /* W: Error control */
-
-/* MMODE: Mode control */
-#define FSI_MMODE_EIP 0x80000000 /* Enable interrupt polling */
-#define FSI_MMODE_ECRC 0x40000000 /* Enable error recovery */
-#define FSI_MMODE_EPC 0x10000000 /* Enable parity checking */
-#define FSI_MMODE_P8_TO_LSB 0x00000010 /* Timeout value LSB */
- /* MSB=1, LSB=0 is 0.8 ms */
- /* MSB=0, LSB=1 is 0.9 ms */
-#define FSI_MMODE_CRS0SHFT 18 /* Clk rate selection 0 shift */
-#define FSI_MMODE_CRS0MASK 0x3ff /* Clk rate selection 0 mask */
-#define FSI_MMODE_CRS1SHFT 8 /* Clk rate selection 1 shift */
-#define FSI_MMODE_CRS1MASK 0x3ff /* Clk rate selection 1 mask */
-
-/* MRESB: Reset brindge */
-#define FSI_MRESB_RST_GEN 0x80000000 /* General reset */
-#define FSI_MRESB_RST_ERR 0x40000000 /* Error Reset */
-
-/* MRESB: Reset port */
-#define FSI_MRESP_RST_ALL_MASTER 0x20000000 /* Reset all FSI masters */
-#define FSI_MRESP_RST_ALL_LINK 0x10000000 /* Reset all FSI port contr. */
-#define FSI_MRESP_RST_MCR 0x08000000 /* Reset FSI master reg. */
-#define FSI_MRESP_RST_PYE 0x04000000 /* Reset FSI parity error */
-#define FSI_MRESP_RST_ALL 0xfc000000 /* Reset any error */
-
-/* MECTRL: Error control */
-#define FSI_MECTRL_EOAE 0x8000 /* Enable machine check when */
- /* master 0 in error */
-#define FSI_MECTRL_P8_AUTO_TERM 0x4000 /* Auto terminate */
-
#define FSI_ENGID_HUB_MASTER 0x1c
-#define FSI_HUB_LINK_OFFSET 0x80000
-#define FSI_HUB_LINK_SIZE 0x80000
-#define FSI_HUB_MASTER_MAX_LINKS 8
#define FSI_LINK_ENABLE_SETUP_TIME 10 /* in mS */
diff --git a/drivers/fsi/fsi-master.h b/drivers/fsi/fsi-master.h
index c7174237e864..6e8d4d4d5149 100644
--- a/drivers/fsi/fsi-master.h
+++ b/drivers/fsi/fsi-master.h
@@ -12,6 +12,71 @@
#include <linux/device.h>
#include <linux/mutex.h>
+/*
+ * Master registers
+ *
+ * These are used by hardware masters, such as the one in the FSP2, AST2600 and
+ * the hub master in POWER processors.
+ */
+
+/* Control Registers */
+#define FSI_MMODE 0x0 /* R/W: mode */
+#define FSI_MDLYR 0x4 /* R/W: delay */
+#define FSI_MCRSP 0x8 /* R/W: clock rate */
+#define FSI_MENP0 0x10 /* R/W: enable */
+#define FSI_MLEVP0 0x18 /* R: plug detect */
+#define FSI_MSENP0 0x18 /* S: Set enable */
+#define FSI_MCENP0 0x20 /* C: Clear enable */
+#define FSI_MAEB 0x70 /* R: Error address */
+#define FSI_MVER 0x74 /* R: master version/type */
+#define FSI_MSTAP0 0xd0 /* R: Port status */
+#define FSI_MRESP0 0xd0 /* W: Port reset */
+#define FSI_MESRB0 0x1d0 /* R: Master error status */
+#define FSI_MRESB0 0x1d0 /* W: Reset bridge */
+#define FSI_MSCSB0 0x1d4 /* R: Master sub command stack */
+#define FSI_MATRB0 0x1d8 /* R: Master address trace */
+#define FSI_MDTRB0 0x1dc /* R: Master data trace */
+#define FSI_MECTRL 0x2e0 /* W: Error control */
+
+/* MMODE: Mode control */
+#define FSI_MMODE_EIP 0x80000000 /* Enable interrupt polling */
+#define FSI_MMODE_ECRC 0x40000000 /* Enable error recovery */
+#define FSI_MMODE_RELA 0x20000000 /* Enable relative address commands */
+#define FSI_MMODE_EPC 0x10000000 /* Enable parity checking */
+#define FSI_MMODE_P8_TO_LSB 0x00000010 /* Timeout value LSB */
+ /* MSB=1, LSB=0 is 0.8 ms */
+ /* MSB=0, LSB=1 is 0.9 ms */
+#define FSI_MMODE_CRS0SHFT 18 /* Clk rate selection 0 shift */
+#define FSI_MMODE_CRS0MASK 0x3ff /* Clk rate selection 0 mask */
+#define FSI_MMODE_CRS1SHFT 8 /* Clk rate selection 1 shift */
+#define FSI_MMODE_CRS1MASK 0x3ff /* Clk rate selection 1 mask */
+
+/* MRESB: Reset brindge */
+#define FSI_MRESB_RST_GEN 0x80000000 /* General reset */
+#define FSI_MRESB_RST_ERR 0x40000000 /* Error Reset */
+
+/* MRESP: Reset port */
+#define FSI_MRESP_RST_ALL_MASTER 0x20000000 /* Reset all FSI masters */
+#define FSI_MRESP_RST_ALL_LINK 0x10000000 /* Reset all FSI port contr. */
+#define FSI_MRESP_RST_MCR 0x08000000 /* Reset FSI master reg. */
+#define FSI_MRESP_RST_PYE 0x04000000 /* Reset FSI parity error */
+#define FSI_MRESP_RST_ALL 0xfc000000 /* Reset any error */
+
+/* MECTRL: Error control */
+#define FSI_MECTRL_EOAE 0x8000 /* Enable machine check when */
+ /* master 0 in error */
+#define FSI_MECTRL_P8_AUTO_TERM 0x4000 /* Auto terminate */
+
+#define FSI_HUB_LINK_OFFSET 0x80000
+#define FSI_HUB_LINK_SIZE 0x80000
+#define FSI_HUB_MASTER_MAX_LINKS 8
+
+/*
+ * Protocol definitions
+ *
+ * These are used by low level masters that bit-bang out the protocol
+ */
+
/* Various protocol delays */
#define FSI_ECHO_DELAY_CLOCKS 16 /* Number clocks for echo delay */
#define FSI_SEND_DELAY_CLOCKS 16 /* Number clocks for send delay */
@@ -47,6 +112,12 @@
/* fsi-master definition and flags */
#define FSI_MASTER_FLAG_SWCLOCK 0x1
+/*
+ * Structures and function prototypes
+ *
+ * These are common to all masters
+ */
+
struct fsi_master {
struct device dev;
int idx;
--
2.24.0.rc1
More information about the openbmc
mailing list