Kernel panic on a p630

[VAKKALANKA RAO Sridhar]

Hi Nathan,

It works for me now

> sym.65.1.0: setting PCI_COMMAND_INVALIDATE.
> sym0: <1010-66> rev 0x1 on pci bus 65 device 1 function 0 irq 325
> sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
> sym0: SCSI BUS has been reset.


Here is the snapshot of my dmesg for scsi:

++++++++++++++++++++
PCI: Enabling device: (0000:41:01.0), cmd 143
sym0: <1010-66> rev 0x1 at pci 0000:41:01.0 irq 103
sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.17a
  Vendor: IBM       Model: IC35L036UCD210-0  Rev: S5BS
  Type:   Direct-Access                      ANSI SCSI revision: 03
sym0:8:0: tagged command queuing enabled, command queue depth 16.
sym0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
  Vendor: IBM       Model: IC35L036UCD210-0  Rev: S5BS
  Type:   Direct-Access                      ANSI SCSI revision: 03
sym0:9:0: tagged command queuing enabled, command queue depth 16.
sym0:9: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
  Vendor: IBM       Model: HSBPD4E  PU3SCSI  Rev: 0015
  Type:   Enclosure                          ANSI SCSI revision: 02
PCI: Enabling device: (0000:41:01.1), cmd 143
sym1: <1010-66> rev 0x1 at pci 0000:41:01.1 irq 104
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.1.17a
PCI: Enabling device: (0001:61:01.0), cmd 143
sym2: <1010-66> rev 0x1 at pci 0001:61:01.0 irq 137
sym2: No NVRAM, ID 7, Fast-80, SE, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.1.17a
sym2:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31)
  Vendor: HP        Model: IBM-C568303030!D  Rev: C209
  Type:   Sequential-Access                  ANSI SCSI revision: 02
PCI: Enabling device: (0001:61:01.1), cmd 143
sym3: <1010-66> rev 0x1 at pci 0001:61:01.1 irq 138
sym3: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym3: SCSI BUS has been reset.
scsi3 : sym-2.1.17a
st: Version 20030811, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi2, channel 0, id 0, lun 0
st0: try direct i/o: yes, max page reachable by HBA 1048576
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
 sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 8, lun 0
++++++++++++++++++++

Thanks again
Sri


** Sent via the linuxppc64-dev mail list. See http://lists.linuxppc.org/