Linux 2.6 boot failure on xup virtex II ppc405
saadia
saadia_dhouib at yahoo.fr
Fri Oct 31 04:56:27 EST 2008
Hi,
I have downloaded the latest linux kernel linux-2.6-xlnx.git from
http://git.xilinx.com/ .
Than I have downloaded the device tree generator device-tree.git from the
same site.
I launched edk 8.2.02, I designed a system with two powerpc cores:
ppc_405_0, ppc_405_1, and opb bus , a plb bus, and the following devices
with their memory map:
BASE HIGH MODULE
0x00000000 0x0FFFFFFF DDR_256MB_32MX64_rank1_row13_col10_cl2_5
0x40600000 0x4060FFFF RS232_Uart_1
0x40C00000 0x40C0FFFF Ethernet_MAC
0x41200000 0x4120FFFF opb_intc_0
0x41800000 0x4180FFFF SysACE_CompactFlash
I generated the bitsteam system.bit.
After getting the device tree generator from
git://git.xilinx.com/device-tree.git, I have copied the 'bsp' directory and
contents so that it can be used by edk XPS. Then I selected 'device-tree' in
the pull down menu labeled 'OS' in the Software Platform Settings dialog
box.
Then selected 'OS and Libraries' on the left, and entered the values for
'console device' and 'bootargs' (respectively
'RS232_Uart_1' and 'console=ttyS0,9600 root=/dev/xsysace/disc0/part3 ip=on'
).
Then I generated libraries and BSP, in the edk_project directory and not in
the linux src directory.
There were those warnings:
*******************************************************************************************************************
--- device tree generator version: v1.1 ---
generating xilinx.dts
Clock Port Summary:
ppc405_0.CPMC405CLOCK connected to proc_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
ppc405_0.PLBCLK connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
reset_block.Slowest_sync_clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb.PLB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
opb.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb2opb.PLB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb2opb.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
RS232_Uart_1.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
Ethernet_MAC.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
SysACE_CompactFlash.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
DDR_256MB_32MX64_rank1_row13_col10_cl2_5.PLB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb_bram_if_cntlr_1.plb_clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb_bram_if_cntlr_1_bram.BRAM_Clk_A connected to
plb_bram_if_cntlr_1_port_BRAM_Clk:
CLK_FREQ_HZ = WARNING: no frequency found!
opb_intc_0.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_0.CLKIN connected to dcm_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_0.CLK0 connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_0.CLK90 connected to clk_90_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_0.CLKFX connected to proc_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = C_CLKFX_MULTIPLY / C_CLKFX_DIVIDE
dcm_1.CLKIN connected to ddr_feedback_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_1.CLK0 connected to dcm_1_FB:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_1.CLK90 connected to ddr_clk_90_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
Clock Frequency: 300000000
IP connected to bus: plb
-master DPLB plb ppc405_0
-master IPLB plb ppc405_0
-slave SPLB plb plb2opb
-slave SPLB plb DDR_256MB_32MX64_rank1_row13_col10_cl2_5
-slave SPLB plb plb_bram_if_cntlr_1
IP connected to bus: opb
-master MOPB opb plb2opb
-slave SOPB opb RS232_Uart_1
-slave SOPB opb Ethernet_MAC
-slave SOPB opb SysACE_CompactFlash
-slave SOPB opb opb_intc_0
WARNING:MDT - Search path /home/dhouib/xupv2p/ directly contains pcores
directory. Search path should point to a directory two levels above
pcores.
WARNING:MDT - Search path /home/dhouib/xupv2p/ directly contains pcores
directory. Search path should point to a directory two levels above
pcores.
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_FREQ_HZ = WARNING: no frequency found!
opb.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb2opb.PLB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb2opb.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
RS232_Uart_1.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
Ethernet_MAC.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
SysACE_CompactFlash.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
DDR_256MB_32MX64_rank1_row13_col10_cl2_5.PLB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb_bram_if_cntlr_1.plb_clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
plb_bram_if_cntlr_1_bram.BRAM_Clk_A connected to
plb_bram_if_cntlr_1_port_BRAM_Clk:
CLK_FREQ_HZ = WARNING: no frequency found!
opb_intc_0.OPB_Clk connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_0.CLKIN connected to dcm_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_0.CLK0 connected to sys_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_0.CLK90 connected to clk_90_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_0.CLKFX connected to proc_clk_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = C_CLKFX_MULTIPLY / C_CLKFX_DIVIDE
dcm_1.CLKIN connected to ddr_feedback_s:
CLK_FREQ_HZ = WARNING: no frequency found!
dcm_1.CLK0 connected to dcm_1_FB:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
dcm_1.CLK90 connected to ddr_clk_90_s:
CLK_FREQ_HZ = WARNING: no frequency found!
CLK_INPORT = CLKIN
CLK_FACTOR = 1
Clock Frequency: 300000000
IP connected to bus: plb
***************************************************************************************************************
***************************************************************************************************************
I copied /ppc_405_0/libsrc/device-tree/xilinx.dts to
/arch/powerpc/boot/dts/virtex405-ml405.dts .
the device tree file looks like this:
****************************************************************************************************
****************************************************************************************************
/*
* Device Tree Generator version: 1.1
*
* (C) Copyright 2007-2008 Xilinx, Inc.
* (C) Copyright 2007-2008 Michal Simek
*
* Michal SIMEK
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
* CAUTION: This file is automatically generated by libgen.
* Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4
*
* XPS project directory: edk_300_100_linux_2-6
*/
/dts-v1/;
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,virtex405", "xlnx,virtex";
model = "testing";
DDR_256MB_32MX64_rank1_row13_col10_cl2_5: memory at 0 {
device_type = "memory";
reg = < 0x0 0x10000000 >;
} ;
chosen {
bootargs = "console=ttyS0,9600 root=/dev/xsysace/disc0/part3 ip=on";
linux,stdout-path = "/plb at 0/opb at 40000000/serial at 40600000";
} ;
cpus {
#address-cells = <1>;
#cpus = <0x1>;
#size-cells = <0>;
ppc405_0: cpu at 0 {
clock-frequency = <300000000>;
compatible = "PowerPC,405", "ibm,ppc405";
d-cache-line-size = <0x20>;
d-cache-size = <0x4000>;
dcr-access-method = "native";
dcr-controller ;
device_type = "cpu";
i-cache-line-size = <0x20>;
i-cache-size = <0x4000>;
model = "PowerPC,405";
reg = <0>;
timebase-frequency = <300000000>;
xlnx,dcr-resync = <0x0>;
xlnx,deterministic-mult = <0x0>;
xlnx,disable-operand-forwarding = <0x1>;
xlnx,mmu-enable = <0x1>;
} ;
} ;
plb: plb at 0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,plb-v34-1.02.a", "simple-bus";
ranges ;
opb: opb at 40000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,opb-v20-1.10.c", "simple-bus";
ranges = < 0x40000000 0x40000000 0x40000000 >;
Ethernet_MAC: ethernet at 40c00000 {
compatible = "xlnx,opb-ethernet-1.04.a";
device_type = "network";
local-mac-address = [ 02 00 00 00 00 00 ];
reg = < 0x40c00000 0x10000 >;
xlnx,cam-bram-0-srl-1 = <0x1>;
xlnx,cam-exist = <0x0>;
xlnx,dev-blk-id = <0x1>;
xlnx,dev-mir-enable = <0x1>;
xlnx,dma-intr-coalesce = <0x1>;
xlnx,dma-present = <0x1>;
xlnx,err-count-exist = <0x1>;
xlnx,family = "virtex2p";
xlnx,fcs-insert-exist = <0x1>;
xlnx,half-duplex-exist = <0x1>;
xlnx,include-dev-pencoder = <0x1>;
xlnx,ipif-rdfifo-depth = <0x8000>;
xlnx,ipif-wrfifo-depth = <0x8000>;
xlnx,jumbo-exist = <0x0>;
xlnx,mac-fifo-bram-1-srl-0 = <0x0>;
xlnx,mac-fifo-depth = <0x40>;
xlnx,mii-exist = <0x1>;
xlnx,miim-clkdvd = <0x1f>;
xlnx,pad-insert-exist = <0x1>;
xlnx,reset-present = <0x1>;
xlnx,rx-dre-type = <0x0>;
xlnx,rx-include-csum = <0x0>;
xlnx,source-addr-insert-exist = <0x1>;
xlnx,tx-dre-type = <0x0>;
xlnx,tx-include-csum = <0x0>;
} ;
RS232_Uart_1: serial at 40600000 {
clock-frequency = "";
compatible = "xlnx,opb-uartlite-1.00.b";
current-speed = <9600>;
device_type = "serial";
interrupt-parent = <&opb_intc_0>;
interrupts = < 1 0 >;
port-number = <0>;
reg = < 0x40600000 0x10000 >;
xlnx,baudrate = <0x9600>;
xlnx,clk-freq = <0x5f5e100>;
xlnx,data-bits = <0x8>;
xlnx,odd-parity = <0x0>;
xlnx,use-parity = <0x0>;
} ;
SysACE_CompactFlash: sysace at 41800000 {
compatible = "xlnx,opb-sysace-1.00.c";
interrupt-parent = <&opb_intc_0>;
interrupts = < 0 2 >;
reg = < 0x41800000 0x10000 >;
xlnx,mem-width = <0x10>;
} ;
opb_intc_0: interrupt-controller at 41200000 {
#interrupt-cells = <0x2>;
compatible = "xlnx,opb-intc-1.00.c";
interrupt-controller ;
reg = < 0x41200000 0x10000 >;
xlnx,num-intr-inputs = <0x2>;
} ;
} ;
} ;
} ;
******************************************************************************************************
******************************************************************************************************
Then cp /arch/powerpc/configs/40x/virtex4_defconfig /.
Then
cd
export ARCH=powerpc
export CROSS_COMPILE=powerpc-405-linux-gnu-
export
PATH=${PATH}:$HOME/xupv2p/opt/crosstool/gcc-3.4.5-glibc-2.3.5/powerpc-405-linux-gnu/bin
make menuconfig
I disabled all the options and enabled only:
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Processor support -> Processor Type AMCC 40x (!!! there is not ppc 40x)
Platform Support -> Generic Xilinx Virtex board
Kernel options -> Kernel support for ELF binaries
Math emulation
Default bootloader kernel arguments
(console=ttyS0,9600) Initial kernel command
string
(simpleImage.virtex405-ml405)
Additional default image types
Device Drivers -> Character Devices -> Virtual Terminal
Serial Devices ->
[*] 8250/16550 and compatible serial
[*] Console on 8250/16550 and compatible serial port
(4) Maximum number of 8250/16550 serial ports
(4) Number of 8250/16550 serial ports to register at runtime
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
Then make clean && make dep && make zImage
I obtained a binary zImage file (and not zImage.elf) !!!! and I obtained
simpleImage.virtex405-ml405.elf in /arch/powerpc/boot .
I used xmd to generated a system.ace from the bitstream and the elf.
The report of xmd is:
******************************************************************************
*****************************************************************************
XMD% xmd -tcl genace.tcl -opt genace1.opt
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 8.2.02 Build EDK_Im_Sp2.4
Copyright (c) 1995-2005 Xilinx, Inc. All rights reserved.
Executing user script : genace.tcl
#######################################################################
XMD GenACE utility. Generate SystemACE File from bit/elf/data Files
#######################################################################
Using GenACE option file : genace1.opt
GenACE Options:
Board : xupv2p
Jtag Devs : xc2vp30
FPGA pos : 1
JPROG : true
HW File :
/home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.bit
ACE File : system3.ace
nCPUs : 1
Processor ppc_hw_1 Information
Debug opt : -debugdevice devicenr 1 cpunr 1
ELF files : simpleImage.virtex405-ml405-3.elf
Start PC Address : 0x00400000
############################################################
Converting Bitstream
'/home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.bit' to SVF
file '/home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.svf'
Executing 'impact -batch bit2svf.scr'
Copying /home/dhouib/xupv2p/edk_300_100_linux_2-6/implementation/system.svf
File to system3.svf File
############################################################
Converting ELF file 'simpleImage.virtex405-ml405-3.elf' to SVF file
'simpleImage.virtex405-ml405-3.svf'
Target reset successfully
section, .text: 0x00400000-0x00408ed4
section, .data: 0x00409000-0x0040ac18
section, __builtin_cmdline: 0x0040ac18-0x0040ae18
section, .kernel:dtb: 0x0040ae18-0x0040be33
section, .kernel:vmlinux.strip: 0x0040c000-0x004c3ae1
section, .bss: 0x004c4000-0x004d0dd8
Downloaded Program simpleImage.virtex405-ml405-3.elf
Setting PC with program start addr = 0x00400000
PC reset to 0x00400000, Clearing MSR Register
Copying simpleImage.virtex405-ml405-3.svf File to system3.svf File
############################################################
Writing Processor JTAG "continue" command to SVF file 'sw_suffix.svf'
PC reset to 0x00400000, Clearing MSR Register
Processor started. Type "stop" to stop processor
############################################################
Converting SVF file 'system3.svf' to SystemACE file 'system3.ace'
Executing 'impact -batch svf2ace.scr'
SystemACE file 'system3.ace' created successfully
********************************************************************************************
********************************************************************************************
I copied the system3.ace (3 because it was the third kernel that I tested
:((( ) to the flash disk partition 1 (Type = FAT16, Size = 32Mo ).
And I booted the kernel.
I got fllowing message on the Terminal:
*****************************************************************************************
zImage starting: loaded at 0x00400000 (sp: 0x004c4efc)
Allocating 0x1acdec bytes for kernel ...
gunzipping (0x00000000 <- 0x0040c000:0x004c3ae1)...done 0x1951b8 bytes
Linux/PowerPC load: console=ttyS0,9600 root=/dev/xsysace/disc0/part3 ip=on
Finalizing device tree... flat tree at 0x40ae18
*******************************************************************************************
My Questions are:
1. Why he stops here?
2. Why I didn't obtained zImage.elf but simpleImage.virtex405-ml405.elf
3. Do I have to copy other files from my (xparameters.h , drivers ) to the
? (I copied only the xilinx.dts file)
Thanks
saadia
--
View this message in context: http://www.nabble.com/Linux-2.6-boot-failure-on-xup-virtex-II-ppc405-tp20252127p20252127.html
Sent from the linuxppc-embedded mailing list archive at Nabble.com.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20081030/60f38304/attachment-0001.htm>
More information about the Linuxppc-embedded
mailing list