regarding kgdb in ppc

[sudheer]

>> In my setup i have one serial port on the target(MPC8540) and one on 
>> host(x86). The document(kgdb_docu_full-2.4.pdf) by default considers 
>> having two serial ports(two on target and two on host).
> To be correct, usually one serial is for serial console, the other-for kgdb. Yet you can either disable serial console, or 
> have its output into kgdb. host requires only one serial to be tied on ppc_85xx-gdb.
>
>   
>> Can anyone plz guide me how to proceed when i have only one serial
>> port . ?
> having one serial is not a comfy case for serial kgdb.
>
>   
>> I want to know the initilization steps for estrablishing the serial 
>> communication between kgdb(in target) and gdb on host. I tried one or 
>> two ways but couldnot succeed.
>>     
>
> I'd consider kgdboe - it works pretty well with 8540 gianfar (or at least used to work for me so tinkering might be trivial).
>   
I have tried with kgdboe. The kernel doesn't wait at any point of time 
and boots completely.

I gave the following bootargs:
console=ttyS0,115200 root=/dev/ram rw kgdboe=@192.168.3.80/, at 192.168.3.14/00:08:A1:84:EF:CA kgdbwait

My Host IP is 192.168.3.14 and that of target's is 80

I could see the following failure comments while kernel booting.

kgdboe: eth0 doesn't support polling, aborting.
kgdboe: netpoll_setup failed kgdboe failed

NET: Registered protocol family 17
kgdb: Waiting for connection from remote gdb...
KGDB cannot initialize I/O yet.
RAMDISK: Compressed image found at block 0

Please help me in sorting out this issue and pl let if am wrong in giving the bootargs.

The whole dump of boot process is as below:

mpc8540ads_init(): exit
id mach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:setio
MMU:exit
setup_arch: enter
setup_arch: bootmem
mpc8540ads_setup_arch()
arch: exit
openpic: enter
openpic: timer
openpic: external
openpic: spurious
openpic: exit

Memory CAM mapping: CAM0=256Mb, CAM1=0Mb, CAM2=0Mb residual: 0Mb
Linux version 2.6.15.5 (root at Sudheer) (gcc version 3.4.4) #43 Tue Jan 23 15:50:57
IST 2007
KGDB cannot initialize I/O yet.
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/ram rw
kgdboe=@192.168.3.80/, at 192.168.3.14/00:08:A1:84:EF:CA kgdbwait
kgdboe: local port 6443
kgdboe: local IP 192.168.3.80
kgdboe: interface eth0
kgdboe: remote port 6442
kgdboe: remote IP 192.168.3.14
kgdboe: remote ethernet address 00:08:a1:84:ef:ca
OpenPIC Version 1.2 (1 CPUs and 60 IRQ sources) at fcfbb000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255744k available (1596k kernel code, 376k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1686k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
Generic PHY: Registered new driver
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO map 0xfdf04500 mem 0xfcffc500 (irq = 26) is a 16550A
serial8250.0: ttyS1 at MMIO map 0xfdf04600 mem 0xfcffb600 (irq = 26) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.2, 00:01:af:07:9b:8a
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.2, 00:01:af:07:9b:8b
eth1: Running with NAPI enabled
eth1: 256/256 RX/TX BD ring size
eth2: Gianfar Ethernet Controller Version 1.2, ff:f8:fe:ff:fb:ff
eth2: Running with NAPI enabled
eth2: 256/256 RX/TX BD ring size
kgdboe: local port 6443
kgdboe: local IP 192.168.3.80
kgdboe: interface eth0
kgdboe: remote port 6442
kgdboe: remote IP 192.168.3.14
kgdboe: remote ethernet address 00:08:a1:84:ef:ca
kgdboe: eth0 doesn't support polling, aborting.
kgdboe: netpoll_setup failed kgdboe failed
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
kgdb: Waiting for connection from remote gdb...
KGDB cannot initialize I/O yet.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 120k init
/usr/sbin/xinetd: error while loading shared libraries: libcrypt.so.1: canno###
Application running ...


BusyBox v0.60.5 (2005.06.07-01:01+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

# phy0:7: Link is Up - 100/Full

#


Thanks
Sudheer
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20070123/69153c56/attachment.htm