Enable a PCMCIA Bluetooth card in custom MPC860 system

[Lo Chun Chung]

Thanks for your hint. But the file is just for Linux Kernel Version 2.6, is this also OK for me? (I am using a 2.4 kernel)
   
  But I doubt that same technique can be applied since the Bluetooth should only be enabled when I loaded the pcmcia drivers (pcmcia_core.o, m8xx_pcmcia.o and ds.o), so .... 
   
  how can I pre-set some settings during boot-time that I have not yet insert the pcmcia modules into the kernel?
   
  Also the last thing is, since there is not "hotplug" in my system and resources allocation is different from standard PCs, so I cannot let my embedded system to auto-detect a standard uart has been added during the PCMCIA bluetooth card is plugged in (while standard PC will)
   
  or can anybody tell me that how can I realize hotplug in my system? (is this can be worked out?)
   
  Thanks

Vitaly Bordug <vbordug at ru.mvista.com> 說：
  Lo Chun Chung wrote:
> Dear all,
> 
> I am a student from Hong Kong. Now I am doing a project about enabling a 
> Bluetooth PCMCIA card (Billionton PCBTC1A-B) in a custom MPC860PC.
> 
> (The custom MPC860 system is constructed by a MPC860 Processor Card and 
> a custom made PCB to adding a PCMCIA interface to the processor Card.)
> 
> Now my stage is: the LINUX (Linux Kernel 2.4.25 from ELDK 3.1 for 
> powerpc) can recognise the card by cardctl, and here are the screen dump:
> 
> / # cardctl ident
> Socket 0:
> product info: "PCMCIA", "Bluetooth Card", "", ""
> manfid: 0x0279, 0x950b
> function: 2 (serial)
> / # cardctl status
> Socket 0:
> 5V 16-bit PC Card
> function 0: [ready], [bat dead], [bat low]
> / # cardctl info
> PRODID_1="PCMCIA"
> PRODID_2="Bluetooth Card"
> PRODID_3=""
> PRODID_4=""
> MANFID=0279,950b
> FUNCID=2
> / # cardct! l config
> Socket 0:
> Vcc 5.0V Vpp1 5.0V Vpp2 5.0V
> 
> but after I load all the modules needed (should be these?)
> 
> / # lsmod
> Module Size Used by Not tainted
> hci_uart 14836 0 (unused)
> l2cap 22956 0 (unused)
> bluez 43856 0 [hci_uart l2cap]
> ds 8060 0
> m8xx_pcmcia 5164 1
> pcmcia_core 39520 0 [ds m8xx_pcmcia]
> 
> my bluetooth still cannot get working ...
> 
> then I try to insert "serial_cs" as my bluetooth card is a uart base 
> card. but some message given out:
> 
> / # insmod serial_cs
> Using /lib/modules/2.4.25/serial_cs.o
> insmod: unresolved symbol unregister_serial
> insmod: unresolved symbol register_serial
> 
> so I realize that I should also insert "serial.o" into the linux, but 
> crashes ...
> 
> / # insmod serial
> Using /lib/modules/2.4.25/serial.o
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ enabled
> Machine check in kernel mode.
> Caused by (from SRR1=1032): Transfer error ack signal
> ! Oops: machine check, sig: 7
> NIP: C3040078 XER: 00000000 LR: C3044724 SP: C1CC1D60 REGS: c1cc1cb0 
> TRAP: 0200 No
> t tainted
> MSR: 00001032 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 11
> TASK = c1cc0000[33] 'busybox' Last syscall: 128
> last math 00000000 last altivec 00000000
> GPR00: 00000000 C1CC1D60 C1CC0000 C1CC1D70 00000004 00000001 00000B4B 
> C015378B
> GPR08: 00000000 800003FC 00000003 C1CC1C70 C0170000 10084438 00000000 
> 00000000
> GPR16: 00000000 00000000 00000000 00000000 00009032 1016EDB0 C1D3A000 
> C1CC1EA0
> GPR24: C1F6B760 00000006 C304973C C1CC1D70 C3040000 00000000 00000000 
> C3046348
> Call backtrace:
> C3044718 C3045188 C0012440 C00043BC 10080000 10021DF0 100238CC
> 1000457C 100041A0 1000436C 1000457C 100041A0 0FE70EF4 00000000
> 
> I only knows when i insert the serial.o, this driver will try to access 
> the standard uart which is not available in my system (my system only 
> has one uart by SMC1), then the system will crash eac! h time the 
> driver wants to access the registers does not available ...
> 
> The project deadline is near ... so I ask here ...
> 
> can anyone helps me or give me some clues?
> 
You should take a look for instance how 8349 does this job (arch/ppc/syslib/ppc83xx_setup.c) - it also has "standard" UART, but some stuff needs to be set up
prior to serial.o. Of course that is not complete solution for your case, just a hint...
> Thanks all
> 
> 
> 
> 
> Best regards,
> Chung
> 
> _______________________________________
> YM - 離線訊息
> 就算你沒有上網，你的朋友仍可以留下訊息給你，當你上網時就能立即看到，任何 
> 說話都冇走失。
> http://messenger.yahoo.com.hk
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded


-- 
Sincerely, 
Vitaly
  



Best regards,
Chung
_______________________________________
 YM - 離線訊息
 就算你沒有上網，你的朋友仍可以留下訊息給你，當你上網時就能立即看到，任何說話都冇走失。
 http://messenger.yahoo.com.hk
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20060110/dd162f62/attachment.htm