Board boots when in BDM, hangs otherwise

[Richard Hendricks]

Note:  This stuff only applies for Metrowerks running bare metal on the
FADS board.

Here are the instructions:
> Changes to PowerPC Runtime Source
>
> Add a __declspec(".init") before "extern void __start(void)" in
> __start.c
> Remove #pragma code_type ".init" in __start.c
> Add the following lines of code to __init_hardware() in
> __ppc_eabi_init.c and .cpp right after the nofralloc
>
>         /* Our address is really in high Flash ROM space.  When reset,
> execution
>          * starts at 0x0100.  This code fragment jumps us to the correct
>          * high memory area */
>
>         lis r3, __init_hardware at h  /* high address of __start */
>         ori r3, r3, __init_hardware at l
>         addi r3, r3, 0x0014  /* Jumps us into the NOPs below */
>         mtctr r3
>         bctr
>
>         nop
>         nop
>
>     /* Now we need to fix the LR since it points back to 0x0000_010x,
>      * not 0x0280_010x like it needs to after we muck up the BCSR's */
>
>     mflr r3
>     oris r3, r3, 0x0280
>     mtlr r3
>
> //Do rest of board setup here, including MSR, IMMR, disable and
> invalidate caches, program UPM, ICTRL, DER, and ICR
>
> Chages to PowerPC Runtime Include
>
> Remove declspec from both __init_hardware() and ADSInit() in file
> __ppc_eabi_init.h
>
> Next recompile Runtime.
> Make sure __ppc_eabi_init in project file points to new modified
> version.
>
> Then goto the project you wish to use flash, and change the Code Address
> to start at 0x02800100.  Since __start is the only function marked as
> .init, it will now be at the correct location, 0x0100 during bootup.
>
> The runtime will also work when not flashing.
>
> This will also allow you to run standalone, and with MPC8bug attached by
> "go 02800100".

I sent them in to Metrowerks, so hopefully their next iteration will
work.  I have also included my whole _FADS.cpp init file.

"Richard Hendricks (ra6353)" wrote:
>
> Jim Lewis wrote:
> >
> > Hi Josh,
> ..
> > Ther is one register that the IN command sets that it does not tell you about. That
> > is the ICTRL register, which controls serialization of the core, among other
> > things. On powerup, it is set to SHOW-ALL-INSTRUCTION-FETCH-CYCLES. Some 8xx
> > processors have problems with this. Read the errata. Check to make sure you are
> > setting ICTRL to something like 0x07 in your firmware.
> >
> > -Jim
>
> This is also probably the source of your slowdown when running
> off of BDM.
>
> Also make sure the watchdog is disabled (Dan's code does this, I think).
>
> If anyone is interested, I can post the startup file I use for
> running from flash on the FADS board using Metrowerks.  I finally
> figured out a way that I can run the same flash image standalone,
> and through MPC8bug.
>
> --
> MPC823 Applications Engineering Development
>

--
MPC823 Applications Engineering Development
-------------- next part --------------
A non-text attachment was scrubbed...
Name: __ppc_eabi_init_FADS.cpp
Type: application/x-unknown-content-type-codewarrior_cpp
Size: 12546 bytes
Desc: not available
Url : http://ozlabs.org/pipermail/linuxppc-embedded/attachments/20000502/03c27860/attachment.bin