[PATCH v2 devicetree 2/2] powerpc: dts: t1040rdb: add ports for Seville Ethernet switch

[Vladimir Oltean]

From: Vladimir Oltean <olteanv at gmail.com>

Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.

A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports. The 2 numbering schemes are
shifted by 8.

Signed-off-by: Vladimir Oltean <vladimir.oltean at nxp.com>
---
Changes in v2:
Use the existing way of accessing the mdio bus and not labels.

 arch/powerpc/boot/dts/fsl/t1040rdb.dts | 115 +++++++++++++++++++++++++
 1 file changed, 115 insertions(+)

diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb.dts b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
index 65ff34c49025..3fd08a2b6dcb 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -64,6 +64,40 @@ mdio at fc000 {
 				phy_sgmii_2: ethernet-phy at 3 {
 					reg = <0x03>;
 				};
+
+				/* VSC8514 QSGMII PHY */
+				phy_qsgmii_0: ethernet-phy at 4 {
+					reg = <0x4>;
+				};
+
+				phy_qsgmii_1: ethernet-phy at 5 {
+					reg = <0x5>;
+				};
+
+				phy_qsgmii_2: ethernet-phy at 6 {
+					reg = <0x6>;
+				};
+
+				phy_qsgmii_3: ethernet-phy at 7 {
+					reg = <0x7>;
+				};
+
+				/* VSC8514 QSGMII PHY */
+				phy_qsgmii_4: ethernet-phy at 8 {
+					reg = <0x8>;
+				};
+
+				phy_qsgmii_5: ethernet-phy at 9 {
+					reg = <0x9>;
+				};
+
+				phy_qsgmii_6: ethernet-phy at a {
+					reg = <0xa>;
+				};
+
+				phy_qsgmii_7: ethernet-phy at b {
+					reg = <0xb>;
+				};
 			};
 		};
 	};
@@ -76,3 +110,84 @@ cpld at 3,0 {
 };
 
 #include "t1040si-post.dtsi"
+
+&seville_switch {
+	status = "okay";
+};
+
+&seville_port0 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_0>;
+	phy-mode = "qsgmii";
+	/* ETH4 written on chassis */
+	label = "swp4";
+	status = "okay";
+};
+
+&seville_port1 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_1>;
+	phy-mode = "qsgmii";
+	/* ETH5 written on chassis */
+	label = "swp5";
+	status = "okay";
+};
+
+&seville_port2 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_2>;
+	phy-mode = "qsgmii";
+	/* ETH6 written on chassis */
+	label = "swp6";
+	status = "okay";
+};
+
+&seville_port3 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_3>;
+	phy-mode = "qsgmii";
+	/* ETH7 written on chassis */
+	label = "swp7";
+	status = "okay";
+};
+
+&seville_port4 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_4>;
+	phy-mode = "qsgmii";
+	/* ETH8 written on chassis */
+	label = "swp8";
+	status = "okay";
+};
+
+&seville_port5 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_5>;
+	phy-mode = "qsgmii";
+	/* ETH9 written on chassis */
+	label = "swp9";
+	status = "okay";
+};
+
+&seville_port6 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_6>;
+	phy-mode = "qsgmii";
+	/* ETH10 written on chassis */
+	label = "swp10";
+	status = "okay";
+};
+
+&seville_port7 {
+	managed = "in-band-status";
+	phy-handle = <&phy_qsgmii_7>;
+	phy-mode = "qsgmii";
+	/* ETH11 written on chassis */
+	label = "swp11";
+	status = "okay";
+};
+
+&seville_port8 {
+	ethernet = <&enet0>;
+	status = "okay";
+};
-- 
2.25.1