[PATCH v8] clk: corenet: Adds the clock binding
Tang Yuantian
Yuantian.Tang at freescale.com
Fri Jan 10 13:29:04 EST 2014
From: Tang Yuantian <yuantian.tang at freescale.com>
Adds the clock bindings for Freescale PowerPC CoreNet platforms
Signed-off-by: Tang Yuantian <Yuantian.Tang at freescale.com>
Signed-off-by: Li Yang <leoli at freescale.com>
---
v8:
- added clock-frequency property description
- fixed whitespace and tab mixing issue
v7:
- refined some properties' definitions
v6:
- splited the previous patch into 2 parts, one is for binding(this one),
the other is for DTS modification(will submit once this gets accepted)
- fixed typo
- refined #clock-cells and clock-output-names properties
- removed fixed-clock compatible string
v5:
- refine the binding document
- update the compatible string
v4:
- add binding document
- update compatible string
- update the reg property
v3:
- fix typo
v2:
- add t4240, b4420, b4860 support
- remove pll/4 clock from p2041, p3041 and p5020 board
.../devicetree/bindings/clock/corenet-clock.txt | 133 +++++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/corenet-clock.txt
diff --git a/Documentation/devicetree/bindings/clock/corenet-clock.txt b/Documentation/devicetree/bindings/clock/corenet-clock.txt
new file mode 100644
index 0000000..abb0493
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/corenet-clock.txt
@@ -0,0 +1,133 @@
+* Clock Block on Freescale CoreNet Platforms
+
+Freescale CoreNet chips take primary clocking input from the external
+SYSCLK signal. The SYSCLK input (frequency) is multiplied using
+multiple phase locked loops (PLL) to create a variety of frequencies
+which can then be passed to a variety of internal logic, including
+cores and peripheral IP blocks.
+Please refer to the Reference Manual for details.
+
+1. Clock Block Binding
+
+Required properties:
+- compatible: Should contain a specific clock block compatible string
+ and a single chassis clock compatible string.
+ Clock block strings include, but not limited to, one of the:
+ * "fsl,p2041-clockgen"
+ * "fsl,p3041-clockgen"
+ * "fsl,p4080-clockgen"
+ * "fsl,p5020-clockgen"
+ * "fsl,p5040-clockgen"
+ * "fsl,t4240-clockgen"
+ * "fsl,b4420-clockgen"
+ * "fsl,b4860-clockgen"
+ Chassis clock strings include:
+ * "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks
+ * "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks
+- reg: Offset and length of the clock register set
+
+Recommended properties:
+- clock-frequency: Input system clock frequency. Must be present
+ if the device has sub-nodes.
+- ranges: Allows valid translation between child's address space and
+ parent's. Must be present if the device has sub-nodes.
+- #address-cells: Specifies the number of cells used to represent
+ physical base addresses. Must be present if the device has
+ sub-nodes and set to 1 if present
+- #size-cells: Specifies the number of cells used to represent
+ the size of an address. Must be present if the device has
+ sub-nodes and set to 1 if present
+
+2. Clock Provider/Consumer Binding
+
+Most of the bindings are from the common clock binding[1].
+ [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : Should include one of the following:
+ * "fsl,qoriq-core-pll-1.0" for core PLL clocks (v1.0)
+ * "fsl,qoriq-core-pll-2.0" for core PLL clocks (v2.0)
+ * "fsl,qoriq-core-mux-1.0" for core mux clocks (v1.0)
+ * "fsl,qoriq-core-mux-2.0" for core mux clocks (v2.0)
+ * "fsl,qoriq-sysclk-1.0": for input system clock (v1.0).
+ It takes parent's clock as its clock.
+ * "fsl,qoriq-sysclk-2.0": for input system clock (v2.0).
+ It takes parent's clock as its clock.
+- #clock-cells: From common clock binding. The number of cells in a
+ clock-specifier. Should be <0> for "fsl,qoriq-sysclk-[1,2].0"
+ clocks, or <1> for "fsl,qoriq-core-pll-[1,2].0" clocks.
+ For "fsl,qoriq-core-pll-[1,2].0" clocks, the single
+ clock-specifier cell may take the following values:
+ * 0 - equal to the PLL frequency
+ * 1 - equal to the PLL frequency divided by 2
+ * 2 - equal to the PLL frequency divided by 4
+
+Recommended properties:
+- clocks: Should be the phandle of input parent clock
+- clock-names: From common clock binding, indicates the clock name
+- clock-output-names: From common clock binding, indicates the names of
+ output clocks
+- reg: Should be the offset and length of clock block base address.
+ The length should be 4.
+
+Example for clock block and clock provider:
+/ {
+ clockgen: global-utilities at e1000 {
+ compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
+ ranges = <0x0 0xe1000 0x1000>;
+ clock-frequency = <0>;
+ reg = <0xe1000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sysclk: sysclk {
+ #clock-cells = <0>;
+ compatible = "fsl,qoriq-sysclk-1.0";
+ clock-output-names = "sysclk";
+ }
+
+ pll0: pll0 at 800 {
+ #clock-cells = <1>;
+ reg = <0x800 0x4>;
+ compatible = "fsl,qoriq-core-pll-1.0";
+ clocks = <&sysclk>;
+ clock-output-names = "pll0", "pll0-div2";
+ };
+
+ pll1: pll1 at 820 {
+ #clock-cells = <1>;
+ reg = <0x820 0x4>;
+ compatible = "fsl,qoriq-core-pll-1.0";
+ clocks = <&sysclk>;
+ clock-output-names = "pll1", "pll1-div2";
+ };
+
+ mux0: mux0 at 0 {
+ #clock-cells = <0>;
+ reg = <0x0 0x4>;
+ compatible = "fsl,qoriq-core-mux-1.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+ clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+ clock-output-names = "cmux0";
+ };
+
+ mux1: mux1 at 20 {
+ #clock-cells = <0>;
+ reg = <0x20 0x4>;
+ compatible = "fsl,qoriq-core-mux-1.0";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+ clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+ clock-output-names = "cmux1";
+ };
+ };
+ }
+
+Example for clock consumer:
+
+/ {
+ cpu0: PowerPC,e5500 at 0 {
+ ...
+ clocks = <&mux0>;
+ ...
+ };
+ }
--
1.8.0
More information about the Linuxppc-dev
mailing list