[PATCH 13/25] powerpc/eeh: No hotplug on permanently removed dev

Gavin Shan gwshan at linux.vnet.ibm.com
Thu Apr 24 18:00:19 EST 2014


The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:

                +-----------------+
                | PE#3     p2p#0  |
                |          p2p#1  |
                +-----------------+
                        |
                +-----------------+
                | PE#4     pdev#0 |
                |          pdev#1 |
                +-----------------+

PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.

The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.

Signed-off-by: Gavin Shan <gwshan at linux.vnet.ibm.com>
---
 arch/powerpc/include/asm/eeh.h       |  1 +
 arch/powerpc/include/asm/ppc-pci.h   |  1 +
 arch/powerpc/kernel/eeh_driver.c     | 48 ++++++++++++++++++++++++++++++------
 arch/powerpc/kernel/eeh_pe.c         | 47 +++++++++++++++++++++++++++++------
 arch/powerpc/kernel/pci_of_scan.c    |  9 +++++++
 arch/powerpc/platforms/powernv/pci.c | 13 +++++++---
 6 files changed, 100 insertions(+), 19 deletions(-)

diff --git a/arch/powerpc/include/asm/eeh.h b/arch/powerpc/include/asm/eeh.h
index f4a9321..2841eca 100644
--- a/arch/powerpc/include/asm/eeh.h
+++ b/arch/powerpc/include/asm/eeh.h
@@ -98,6 +98,7 @@ struct eeh_pe {
 
 #define EEH_DEV_NO_HANDLER	(1 << 8)	/* No error handler	*/
 #define EEH_DEV_SYSFS		(1 << 9)	/* Sysfs created	*/
+#define EEH_DEV_REMOVED		(1 << 10)	/* Removed permanently	*/
 
 struct eeh_dev {
 	int mode;			/* EEH mode			*/
diff --git a/arch/powerpc/include/asm/ppc-pci.h b/arch/powerpc/include/asm/ppc-pci.h
index ed57fa7..db1e2b8 100644
--- a/arch/powerpc/include/asm/ppc-pci.h
+++ b/arch/powerpc/include/asm/ppc-pci.h
@@ -58,6 +58,7 @@ int rtas_write_config(struct pci_dn *, int where, int size, u32 val);
 int rtas_read_config(struct pci_dn *, int where, int size, u32 *val);
 void eeh_pe_state_mark(struct eeh_pe *pe, int state);
 void eeh_pe_state_clear(struct eeh_pe *pe, int state);
+void eeh_pe_dev_mode_mark(struct eeh_pe *pe, int mode);
 
 void eeh_sysfs_add_device(struct pci_dev *pdev);
 void eeh_sysfs_remove_device(struct pci_dev *pdev);
diff --git a/arch/powerpc/kernel/eeh_driver.c b/arch/powerpc/kernel/eeh_driver.c
index 1f1e2cc..f99ba9b 100644
--- a/arch/powerpc/kernel/eeh_driver.c
+++ b/arch/powerpc/kernel/eeh_driver.c
@@ -171,6 +171,15 @@ static void eeh_enable_irq(struct pci_dev *dev)
 	}
 }
 
+static bool eeh_dev_removed(struct eeh_dev *edev)
+{
+	/* EEH device removed ? */
+	if (!edev || (edev->mode & EEH_DEV_REMOVED))
+		return true;
+
+	return false;
+}
+
 /**
  * eeh_report_error - Report pci error to each device driver
  * @data: eeh device
@@ -187,10 +196,8 @@ static void *eeh_report_error(void *data, void *userdata)
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver;
 
-	/* We might not have the associated PCI device,
-	 * then we should continue for next one.
-	 */
-	if (!dev) return NULL;
+	if (!dev || eeh_dev_removed(edev))
+		return NULL;
 	dev->error_state = pci_channel_io_frozen;
 
 	driver = eeh_pcid_get(dev);
@@ -230,6 +237,9 @@ static void *eeh_report_mmio_enabled(void *data, void *userdata)
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver;
 
+	if (!dev || eeh_dev_removed(edev))
+		return NULL;
+
 	driver = eeh_pcid_get(dev);
 	if (!driver) return NULL;
 
@@ -267,7 +277,8 @@ static void *eeh_report_reset(void *data, void *userdata)
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver;
 
-	if (!dev) return NULL;
+	if (!dev || eeh_dev_removed(edev))
+		return NULL;
 	dev->error_state = pci_channel_io_normal;
 
 	driver = eeh_pcid_get(dev);
@@ -307,7 +318,8 @@ static void *eeh_report_resume(void *data, void *userdata)
 	struct pci_dev *dev = eeh_dev_to_pci_dev(edev);
 	struct pci_driver *driver;
 
-	if (!dev) return NULL;
+	if (!dev || eeh_dev_removed(edev))
+		return NULL;
 	dev->error_state = pci_channel_io_normal;
 
 	driver = eeh_pcid_get(dev);
@@ -343,7 +355,8 @@ static void *eeh_report_failure(void *data, void *userdata)
 	struct pci_dev *dev = eeh_dev_to_pci_dev(edev);
 	struct pci_driver *driver;
 
-	if (!dev) return NULL;
+	if (!dev || eeh_dev_removed(edev))
+		return NULL;
 	dev->error_state = pci_channel_io_perm_failure;
 
 	driver = eeh_pcid_get(dev);
@@ -380,6 +393,16 @@ static void *eeh_rmv_device(void *data, void *userdata)
 	if (!dev || (dev->hdr_type & PCI_HEADER_TYPE_BRIDGE))
 		return NULL;
 
+	/*
+	 * We rely on count-based pcibios_release_device() to
+	 * detach permanently offlined PEs. Unfortunately, that's
+	 * not reliable enough. We might have the permanently
+	 * offlined PEs attached, but we needn't take care of
+	 * them and their child devices.
+	 */
+	if (eeh_dev_removed(edev))
+		return NULL;
+
 	driver = eeh_pcid_get(dev);
 	if (driver) {
 		eeh_pcid_put(dev);
@@ -694,8 +717,17 @@ perm_error:
 	/* Notify all devices that they're about to go down. */
 	eeh_pe_dev_traverse(pe, eeh_report_failure, NULL);
 
-	/* Shut down the device drivers for good. */
+	/* Mark the PE to be removed permanently */
+	pe->freeze_count = EEH_MAX_ALLOWED_FREEZES + 1;
+
+	/*
+	 * Shut down the device drivers for good. We mark
+	 * all removed devices correctly to avoid access
+	 * the their PCI config any more.
+	 */
 	if (frozen_bus) {
+		eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
+
 		pci_lock_rescan_remove();
 		pcibios_remove_pci_devices(frozen_bus);
 		pci_unlock_rescan_remove();
diff --git a/arch/powerpc/kernel/eeh_pe.c b/arch/powerpc/kernel/eeh_pe.c
index f0c353f..995c2a2 100644
--- a/arch/powerpc/kernel/eeh_pe.c
+++ b/arch/powerpc/kernel/eeh_pe.c
@@ -503,13 +503,17 @@ static void *__eeh_pe_state_mark(void *data, void *flag)
 	struct eeh_dev *edev, *tmp;
 	struct pci_dev *pdev;
 
-	/*
-	 * Mark the PE with the indicated state. Also,
-	 * the associated PCI device will be put into
-	 * I/O frozen state to avoid I/O accesses from
-	 * the PCI device driver.
-	 */
+	/* Keep the state of permanently removed PE intact */
+	if ((pe->freeze_count > EEH_MAX_ALLOWED_FREEZES) &&
+	    (state & (EEH_PE_ISOLATED | EEH_PE_RECOVERING)))
+		return NULL;
+
 	pe->state |= state;
+
+	/* Offline PCI devices if applicable */
+	if (state != EEH_PE_ISOLATED)
+		return NULL;
+
 	eeh_pe_for_each_dev(pe, edev, tmp) {
 		pdev = eeh_dev_to_pci_dev(edev);
 		if (pdev)
@@ -532,6 +536,27 @@ void eeh_pe_state_mark(struct eeh_pe *pe, int state)
 	eeh_pe_traverse(pe, __eeh_pe_state_mark, &state);
 }
 
+static void *__eeh_pe_dev_mode_mark(void *data, void *flag)
+{
+	struct eeh_dev *edev = data;
+	int mode = *((int *)flag);
+
+	edev->mode |= mode;
+
+	return NULL;
+}
+
+/**
+ * eeh_pe_dev_state_mark - Mark state for all device under the PE
+ * @pe: EEH PE
+ *
+ * Mark specific state for all child devices of the PE.
+ */
+void eeh_pe_dev_mode_mark(struct eeh_pe *pe, int mode)
+{
+	eeh_pe_dev_traverse(pe, __eeh_pe_dev_mode_mark, &mode);
+}
+
 /**
  * __eeh_pe_state_clear - Clear state for the PE
  * @data: EEH PE
@@ -546,8 +571,16 @@ static void *__eeh_pe_state_clear(void *data, void *flag)
 	struct eeh_pe *pe = (struct eeh_pe *)data;
 	int state = *((int *)flag);
 
+	/* Keep the state of permanently removed PE intact */
+	if ((pe->freeze_count > EEH_MAX_ALLOWED_FREEZES) &&
+	    (state & EEH_PE_ISOLATED))
+		return NULL;
+
 	pe->state &= ~state;
-	pe->check_count = 0;
+
+	/* Clear check count since last isolation */
+	if (state & EEH_PE_ISOLATED)
+		pe->check_count = 0;
 
 	return NULL;
 }
diff --git a/arch/powerpc/kernel/pci_of_scan.c b/arch/powerpc/kernel/pci_of_scan.c
index 83c26d8..ea6470c 100644
--- a/arch/powerpc/kernel/pci_of_scan.c
+++ b/arch/powerpc/kernel/pci_of_scan.c
@@ -304,6 +304,9 @@ static struct pci_dev *of_scan_pci_dev(struct pci_bus *bus,
 	struct pci_dev *dev = NULL;
 	const __be32 *reg;
 	int reglen, devfn;
+#ifdef CONFIG_EEH
+	struct eeh_dev *edev = of_node_to_eeh_dev(dn);
+#endif
 
 	pr_debug("  * %s\n", dn->full_name);
 	if (!of_device_is_available(dn))
@@ -321,6 +324,12 @@ static struct pci_dev *of_scan_pci_dev(struct pci_bus *bus,
 		return dev;
 	}
 
+	/* Device removed permanently ? */
+#ifdef CONFIG_EEH
+	if (edev && (edev->mode & EEH_DEV_REMOVED))
+		return NULL;
+#endif
+
 	/* create a new pci_dev for this device */
 	dev = of_create_pci_dev(dn, bus, devfn);
 	if (!dev)
diff --git a/arch/powerpc/platforms/powernv/pci.c b/arch/powerpc/platforms/powernv/pci.c
index f98cf99..eefbfcc 100644
--- a/arch/powerpc/platforms/powernv/pci.c
+++ b/arch/powerpc/platforms/powernv/pci.c
@@ -441,11 +441,16 @@ static bool pnv_pci_cfg_check(struct pci_controller *hose,
 	if (!(phb->flags & PNV_PHB_FLAG_EEH))
 		return true;
 
-	/* PE reset ? */
+	/* PE reset or device removed ? */
 	edev = of_node_to_eeh_dev(dn);
-	if (edev && edev->pe &&
-	    (edev->pe->state & EEH_PE_RESET))
-		return false;
+	if (edev) {
+		if (edev->pe &&
+		    (edev->pe->state & EEH_PE_RESET))
+			return false;
+
+		if (edev->mode & EEH_DEV_REMOVED)
+			return false;
+	}
 
 	return true;
 }
-- 
1.8.3.2



More information about the Linuxppc-dev mailing list