[PATCH v4 2/3] devcietree: bindings: add some MFD Keymile FPGAs

[Valentin Longchamp]

These are the bindings for 2 MFD devices used on some of the Keymile boards.
The first one is the chassis managmenet bfticu FPGA.
The second one is the board controller (reset, LEDs, GPIOs) QRIO CPDL.
These FPGAs are used in the kmcoge4 board.

Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>

---

Changes in v4:
- remove the addition of the KEYMILE vendor-prefix as it is already
  picked by Rob
- Take Scott's and Rob's comments regarding the bindings for the
  interrupt-cells into account

Changes in v3:
- add a patch with the bindings for the KEYMILE FPGAs

Changes in v2: None

 Documentation/devicetree/bindings/mfd/bfticu.txt | 25 ++++++++++++++++++++++++
 Documentation/devicetree/bindings/mfd/qriox.txt  | 17 ++++++++++++++++
 2 files changed, 42 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/bfticu.txt
 create mode 100644 Documentation/devicetree/bindings/mfd/qriox.txt

diff --git a/Documentation/devicetree/bindings/mfd/bfticu.txt b/Documentation/devicetree/bindings/mfd/bfticu.txt
new file mode 100644
index 0000000..65c9077
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/bfticu.txt
@@ -0,0 +1,25 @@
+KEYMILE bfticu Chassis Management FPGA
+
+The bfticu is a multifunction device that manages the whole chassis.
+Its main functionality is to collect IRQs from the whole chassis and signals
+them to a single controller.
+
+Required properties:
+- compatible: "keymile,bfticu"
+- interrupt-controller: the bfticu FPGA is an interrupt controller
+- interrupts: the main IRQ line to signal the collected IRQs
+- #interrupt-cells : is 2 and their usage is compliant to the 2 cells variant
+  of Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- interrupt-parent: the parent IRQ ctrl the main IRQ is connected to
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	chassis-mgmt at 3,0 {
+		compatible = "keymile,bfticu";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <3 0 0x100>;
+		interrupt-parent = <&mpic>;
+		interrupts = <6 1 0 0>;
+	};
diff --git a/Documentation/devicetree/bindings/mfd/qriox.txt b/Documentation/devicetree/bindings/mfd/qriox.txt
new file mode 100644
index 0000000..f301e2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qriox.txt
@@ -0,0 +1,17 @@
+KEYMILE qrio Board Control CPLD
+
+The qrio is a multifunction device that controls the KEYMILE boards based on
+the kmp204x design.
+It is consists of a reset controller, watchdog timer, LEDs, and 2 IRQ capable
+GPIO blocks.
+
+Required properties:
+- compatible: "keymile,qriox"
+- reg: access on the parent local bus (chip select, offset in chip select, size)
+
+Example:
+
+	board-control at 1,0 {
+		compatible = "keymile,qriox";
+		reg = <1 0 0x80>;
+	};
-- 
1.8.0.1