[PATCH] powerpc/85xx: Enable MTD/NOR/NAND options by default in defconfig

[Shengzhou Liu]

Enable MTD/NOR/NAND options by default in mpc85xx_defconfig and
mpc85xx_smp_defconfig to support NOR, NAND flash.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu at freescale.com>
---
based on master branch of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git

 arch/powerpc/configs/mpc85xx_defconfig     |   26 ++++++++++++++++++++++++++
 arch/powerpc/configs/mpc85xx_smp_defconfig |   25 +++++++++++++++++++++++++
 2 files changed, 51 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/configs/mpc85xx_defconfig b/arch/powerpc/configs/mpc85xx_defconfig
index d6b6df5..a42304d 100644
--- a/arch/powerpc/configs/mpc85xx_defconfig
+++ b/arch/powerpc/configs/mpc85xx_defconfig
@@ -39,6 +39,7 @@ CONFIG_TQM8560=y
 CONFIG_SBC8548=y
 CONFIG_QUICC_ENGINE=y
 CONFIG_QE_GPIO=y
+CONFIG_MPC8xxx_GPIO=y
 CONFIG_HIGHMEM=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -74,6 +75,31 @@ CONFIG_INET_ESP=y
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_FTL=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_MTD_NAND_FSL_IFC=y
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_M25P80=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
diff --git a/arch/powerpc/configs/mpc85xx_smp_defconfig b/arch/powerpc/configs/mpc85xx_smp_defconfig
index 5b0e292..31ef74f 100644
--- a/arch/powerpc/configs/mpc85xx_smp_defconfig
+++ b/arch/powerpc/configs/mpc85xx_smp_defconfig
@@ -76,6 +76,31 @@ CONFIG_INET_ESP=y
 CONFIG_IPV6=y
 CONFIG_IP_SCTP=m
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_FTL=y
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_MTD_NAND_FSL_IFC=y
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_M25P80=y
 CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
-- 
1.7.0.4