[PATCH v2] powerpc/85xx: Add P1021MDS board support
Haiying Wang
Haiying.Wang at freescale.com
Sat May 22 00:16:12 EST 2010
P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)
Signed-off-by: Haiying Wang <Haiying.Wang at freescale.com>
Signed-off-by: Yu Liu <Yu.Liu at freescale.com>
---
v2: address the comments from Kumar.
arch/powerpc/boot/dts/p1021mds.dts | 698 +++++++++++++++++++++++++++++
arch/powerpc/platforms/85xx/mpc85xx_mds.c | 102 ++++-
2 files changed, 797 insertions(+), 3 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1021mds.dts
diff --git a/arch/powerpc/boot/dts/p1021mds.dts b/arch/powerpc/boot/dts/p1021mds.dts
new file mode 100644
index 0000000..7fad2df
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021mds.dts
@@ -0,0 +1,698 @@
+/*
+ * P1021 MDS Device Tree Source
+ *
+ * Copyright 2010 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+ model = "fsl,P1021";
+ compatible = "fsl,P1021MDS";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ ethernet4 = &enet4;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1021 at 0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1021 at 1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus at ffe05000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
+ reg = <0 0xffe05000 0 0x1000>;
+ interrupts = <19 2>;
+ interrupt-parent = <&mpic>;
+
+ /* NAND Flash, BCSR, PMC0/1*/
+ ranges = <0x0 0x0 0x0 0xfc000000 0x02000000
+ 0x1 0x0 0x0 0xf8000000 0x00008000
+ 0x2 0x0 0x0 0xf8010000 0x00020000
+ 0x3 0x0 0x0 0xf8020000 0x00020000>;
+
+ nand at 0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1021-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x0 0x0 0x40000>;
+
+ partition at 0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND (RO) U-Boot Image";
+ read-only;
+ };
+
+ partition at 100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND (RO) DTB Image";
+ read-only;
+ };
+
+ partition at 200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition at 600000 {
+ /* 5MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00500000>;
+ label = "NAND (RO) Compressed RFS Image";
+ read-only;
+ };
+
+ partition at b00000 {
+ /* 6MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00600000>;
+ label = "NAND (RW) JFFS2 Root File System";
+ };
+
+ partition at 1100000 {
+ /* 14MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00e00000>;
+ label = "NAND (RW) Writable User area";
+ };
+
+ partition at 1f00000 {
+ /* 1MB for microcode */
+ reg = <0x01f00000 0x00100000>;
+ label = "NAND (RO) QE Ucode";
+ read-only;
+ };
+ };
+
+ bcsr at 1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1021mds-bcsr";
+ reg = <1 0 0x8000>;
+ ranges = <0 1 0 0x8000>;
+ };
+
+ pib at 2,0 {
+ compatible = "fsl,p1021mds-pib";
+ reg = <2 0 0x10000>;
+ };
+
+ pib at 3,0 {
+ compatible = "fsl,p1021mds-pib";
+ reg = <3 0 0x10000>;
+ };
+ };
+
+ soc at ffe00000 {
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1021-immr", "simple-bus";
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law at 0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm at 1000 {
+ compatible = "fsl,p1021-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ memory-controller at 2000 {
+ compatible = "fsl,p1021-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+
+ i2c at 3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ rtc at 68 {
+ compatible = "dallas,ds1374";
+ reg = <0x68>;
+ };
+ };
+
+ i2c at 3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ serial0: serial at 4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ serial1: serial at 4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ spi at 7000 {
+ cell-index = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,espi";
+ reg = <0x7000 0x1000>;
+ interrupts = <59 0x2>;
+ interrupt-parent = <&mpic>;
+ espi,num-ss-bits = <4>;
+ mode = "cpu";
+
+ fsl_m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,espi-flash";
+ reg = <0>;
+ linux,modalias = "fsl_m25p80";
+ spi-max-frequency = <40000000>; /* input clock */
+ partition at u-boot {
+ label = "u-boot-spi";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition at kernel {
+ label = "kernel-spi";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition at dtb {
+ label = "dtb-spi";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition at fs {
+ label = "file system-spi";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+ };
+
+ gpio: gpio-controller at f000 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8572-gpio";
+ reg = <0xf000 0x100>;
+ interrupts = <47 0x2>;
+ interrupt-parent = <&mpic>;
+ gpio-controller;
+ };
+
+ L2: l2-cache-controller at 20000 {
+ compatible = "fsl,p1021-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+
+ dma at 21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel at 0 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel at 80 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel at 100 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel at 180 {
+ compatible = "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
+ usb at 22000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl-usb2-dr";
+ reg = <0x22000 0x1000>;
+ interrupt-parent = <&mpic>;
+ interrupts = <28 0x2>;
+ phy_type = "ulpi";
+ };
+
+ mdio at 24000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,etsec2-mdio";
+ reg = <0x24000 0x1000 0xb0030 0x4>;
+
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <1 1>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+ phy4: ethernet-phy at 4 {
+ interrupt-parent = <&mpic>;
+ reg = <0x4>;
+ };
+ };
+
+ mdio at 25000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,etsec2-tbi";
+ reg = <0x25000 0x1000 0xb1030 0x4>;
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at B0000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+ queue-group at 0{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB0000 0x1000>;
+ interrupts = <29 2 30 2 34 2>;
+ };
+ queue-group at 1{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB4000 0x1000>;
+ interrupts = <17 2 18 2 24 2>;
+ };
+ };
+
+ enet1: ethernet at B1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy4>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ queue-group at 0{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB1000 0x1000>;
+ interrupts = <35 2 36 2 40 2>;
+ };
+ queue-group at 1{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB5000 0x1000>;
+ interrupts = <51 2 52 2 67 2>;
+ };
+ };
+
+ enet2: ethernet at B2000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "fsl,etsec2";
+ fsl,num_rx_queues = <0x8>;
+ fsl,num_tx_queues = <0x8>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ queue-group at 0{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB2000 0x1000>;
+ interrupts = <31 2 32 2 33 2>;
+ };
+ queue-group at 1{
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xB6000 0x1000>;
+ interrupts = <25 2 26 2 27 2>;
+ };
+ };
+
+ sdhci at 2e000 {
+ compatible = "fsl,p1021-esdhc", "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <72 0x2>;
+ interrupt-parent = <&mpic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
+ };
+
+ crypto at 30000 {
+ compatible = "fsl,sec3.3", "fsl,sec3.1",
+ "fsl,sec3.0", "fsl,sec2.4",
+ "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+ reg = <0x30000 0x10000>;
+ interrupts = <45 2 58 2>;
+ interrupt-parent = <&mpic>;
+ fsl,num-channels = <4>;
+ fsl,channel-fifo-len = <24>;
+ fsl,exec-units-mask = <0x97c>;
+ fsl,descriptor-types-mask = <0x3a30abf>;
+ };
+
+ mpic: pic at 40000 {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x40000 0x40000>;
+ compatible = "chrp,open-pic";
+ device_type = "open-pic";
+ };
+
+ msi at 41600 {
+ compatible = "fsl,p1021-msi", "fsl,mpic-msi";
+ reg = <0x41600 0x80>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe0 0
+ 0xe1 0
+ 0xe2 0
+ 0xe3 0
+ 0xe4 0
+ 0xe5 0
+ 0xe6 0
+ 0xe7 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ global-utilities at e0000 { //global utilities block
+ compatible = "fsl,p1021-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+
+ par_io at e0100 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xe0100 0x60>;
+ ranges = <0x0 0xe0100 0x60>;
+ device_type = "par_io";
+ num-ports = <3>;
+ pio1: ucc_pin at 01 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
+ 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9
+*/
+ 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
+ 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
+ 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
+ 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
+ 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
+ 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
+ 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
+ 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
+ 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
+ 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
+ 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
+ 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
+ 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
+ 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
+ };
+
+ pio2: ucc_pin at 02 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
+ 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
+ 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
+ 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
+ 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
+ 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
+ 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
+ 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
+ };
+ };
+ };
+
+ pci0: pcie at ffe09000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0 0xffe09000 0 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ clock-frequency = <33333333>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 4 1
+ 0000 0 0 2 &mpic 5 1
+ 0000 0 0 3 &mpic 6 1
+ 0000 0 0 4 &mpic 7 1
+ >;
+ pcie at 0 {
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie at ffe0a000 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0 0xffe0a000 0 0x1000>;
+ bus-range = <0 255>;
+ ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
+ clock-frequency = <33333333>;
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 0 1
+ 0000 0 0 2 &mpic 1 1
+ 0000 0 0 3 &mpic 2 1
+ 0000 0 0 4 &mpic 3 1
+ >;
+ pcie at 0 {
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe at ffe80000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ ranges = <0x0 0x0 0xffe80000 0x40000>;
+ reg = <0 0xffe80000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: interrupt-controller at 80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <63 2 60 2>; //high:47 low:44
+ interrupt-parent = <&mpic>;
+ };
+
+ enet3: ucc at 2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "clk12";
+ tx-clock-name = "clk9";
+ pio-handle = <&pio1>;
+ phy-handle = <&qe_phy0>;
+ phy-connection-type = "mii";
+ };
+
+ mdio at 2120 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2120 0x18>;
+ compatible = "fsl,ucc-mdio";
+
+ qe_phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <4 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ qe_phy1: ethernet-phy at 03 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet4: ucc at 2400 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <5>;
+ reg = <0x2400 0x200>;
+ interrupts = <40>;
+ interrupt-parent = <&qeic>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "none";
+ tx-clock-name = "clk13";
+ pio-handle = <&pio2>;
+ phy-handle = <&qe_phy1>;
+ phy-connection-type = "rmii";
+ };
+
+ muram at 10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x6000>;
+
+ data-only at 0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x6000>;
+ };
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index f0684c8..8fe87fc 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -1,5 +1,5 @@
/*
- * Copyright (C) Freescale Semicondutor, Inc. 2006-2007. All rights reserved.
+ * Copyright (C) Freescale Semicondutor, Inc. 2006-2010. All rights reserved.
*
* Author: Andy Fleming <afleming at freescale.com>
*
@@ -154,6 +154,10 @@ static int mpc8568_mds_phy_fixups(struct phy_device *phydev)
* Setup the architecture
*
*/
+#ifdef CONFIG_SMP
+extern void __init mpc85xx_smp_init(void);
+#endif
+
static void __init mpc85xx_mds_setup_arch(void)
{
struct device_node *np;
@@ -194,6 +198,10 @@ static void __init mpc85xx_mds_setup_arch(void)
}
#endif
+#ifdef CONFIG_SMP
+ mpc85xx_smp_init();
+#endif
+
#ifdef CONFIG_QUICC_ENGINE
np = of_find_compatible_node(NULL, NULL, "fsl,qe");
if (!np) {
@@ -271,9 +279,49 @@ static void __init mpc85xx_mds_setup_arch(void)
BCSR_UCC_RGMII, BCSR_UCC_RTBI);
}
+ } else if (machine_is(p1021_mds)) {
+#define BCSR11_ENET_MICRST (0x1 << 5)
+ /* Reset Micrel PHY */
+ clrbits8(&bcsr_regs[11], BCSR11_ENET_MICRST);
+ setbits8(&bcsr_regs[11], BCSR11_ENET_MICRST);
}
+
iounmap(bcsr_regs);
}
+
+ if (machine_is(p1021_mds)) {
+#define MPC85xx_PMUXCR_OFFSET 0x60
+#define MPC85xx_PMUXCR_QE0 0x00008000
+#define MPC85xx_PMUXCR_QE3 0x00001000
+#define MPC85xx_PMUXCR_QE9 0x00000040
+#define MPC85xx_PMUXCR_QE12 0x00000008
+ static __be32 __iomem *pmuxcr;
+
+ np = of_find_node_by_name(NULL, "global-utilities");
+
+ if (np) {
+ pmuxcr = of_iomap(np, 0) + MPC85xx_PMUXCR_OFFSET;
+
+ if (!pmuxcr)
+ printk(KERN_EMERG "Error: Alternate function"
+ " signal multiplex control register not"
+ " mapped!\n");
+ else
+ /* P1021 has pins muxed for QE and other functions. To
+ * enable QE UEC mode, we need to set bit QE0 for UCC1
+ * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
+ * and QE12 for QE MII management singals in PMUXCR
+ * register.
+ */
+ setbits32(pmuxcr, MPC85xx_PMUXCR_QE0 |
+ MPC85xx_PMUXCR_QE3 |
+ MPC85xx_PMUXCR_QE9 |
+ MPC85xx_PMUXCR_QE12);
+
+ of_node_put(np);
+ }
+
+ }
#endif /* CONFIG_QUICC_ENGINE */
#ifdef CONFIG_SWIOTLB
@@ -330,6 +378,16 @@ static struct of_device_id mpc85xx_ids[] = {
{},
};
+static struct of_device_id p1021_ids[] = {
+ { .type = "soc", },
+ { .compatible = "soc", },
+ { .compatible = "simple-bus", },
+ { .type = "qe", },
+ { .compatible = "fsl,qe", },
+ { .compatible = "gianfar", },
+ {},
+};
+
static int __init mpc85xx_publish_devices(void)
{
if (machine_is(mpc8568_mds))
@@ -342,11 +400,22 @@ static int __init mpc85xx_publish_devices(void)
return 0;
}
+
+static int __init p1021_publish_devices(void)
+{
+ /* Publish the QE devices */
+ of_platform_bus_probe(NULL, p1021_ids, NULL);
+
+ return 0;
+}
+
machine_device_initcall(mpc8568_mds, mpc85xx_publish_devices);
machine_device_initcall(mpc8569_mds, mpc85xx_publish_devices);
+machine_device_initcall(p1021_mds, p1021_publish_devices);
machine_arch_initcall(mpc8568_mds, swiotlb_setup_bus_notifier);
machine_arch_initcall(mpc8569_mds, swiotlb_setup_bus_notifier);
+machine_arch_initcall(p1021_mds, swiotlb_setup_bus_notifier);
static void __init mpc85xx_mds_pic_init(void)
{
@@ -366,7 +435,7 @@ static void __init mpc85xx_mds_pic_init(void)
mpic = mpic_alloc(np, r.start,
MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN |
- MPIC_BROKEN_FRR_NIRQS,
+ MPIC_BROKEN_FRR_NIRQS | MPIC_SINGLE_DEST_CPU,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
of_node_put(np);
@@ -380,7 +449,11 @@ static void __init mpc85xx_mds_pic_init(void)
if (!np)
return;
}
- qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL);
+ if (machine_is(p1021_mds))
+ qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
+ qe_ic_cascade_high_mpic);
+ else
+ qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL);
of_node_put(np);
#endif /* CONFIG_QUICC_ENGINE */
}
@@ -426,3 +499,26 @@ define_machine(mpc8569_mds) {
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
};
+
+static int __init p1021_mds_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "fsl,P1021MDS");
+
+}
+
+define_machine(p1021_mds) {
+ .name = "P1021 MDS",
+ .probe = p1021_mds_probe,
+ .setup_arch = mpc85xx_mds_setup_arch,
+ .init_IRQ = mpc85xx_mds_pic_init,
+ .get_irq = mpic_get_irq,
+ .restart = fsl_rstcr_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+#endif
+};
+
--
1.6.0.2
More information about the Linuxppc-dev
mailing list