USB host on 83xx

[Gary Thomas]

On 01/27/2010 05:05 PM, Gary Thomas wrote:
> On 01/27/2010 01:20 PM, Gary Thomas wrote:
>> I have two nearly identical boards, with very different behavior.
>>
>> Older 8347 (PVR: 0x80830011)
>> New 8347 (PVR: 0x80830031)
>
> I lied (more precisely I was lied to and I passed it on - I've never
> seen these boards in person, just worked on them from thousands of
> miles away).
>
> The boards have more than a rev difference:
> OLD - 8347EA (SVR: 0x80540011, PVR: 0x80830011)
> NEW - 8343E (SVR: 0x80570030, PVR: 0x80830031)

This turned out to be a powerup/strapping issue.  This is now fixed
and the SVR is 0x80550030 on the failing board.  No change in behavior.

Does anyone have any ideas about this?

>
> Could this have any bearing on the problems?
>
>> I've tried a number of kernels (vintages) on both with wild results.
>>
>> 2.6.20 - Same kernel works on both(*)
>> 2.6.28 - Kernel runs great on OLD, machine check on NEW
>> 2.6.32.6 - Ditto
>>
>> The problem occurs (only on the new silicon) during the USB host
>> initialization. The root hub is found and initialized, then the
>> EHCI subsystem is reset (to force it to find siblings on the bus).
>> This results in a machine check at the point where the PHY is
>> being reinitialized.
>>
>> I've peppered the driver with messages - here's what I see:
>>
>> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
>> fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
>> ********** ehci_fsl_setup.272
>> ********** ehci_fsl_setup.296
>> ********** ehci_fsl_setup.299
>> ********** ehci_fsl_reinit.257
>> ********** mpc83xx_usb_setup.192
>> ********** mpc83xx_usb_setup.207
>> ********** mpc83xx_usb_setup.215
>> ********** mpc83xx_usb_setup.220
>> ********** mpc83xx_setup_phy.163
>> ********** mpc83xx_setup_phy.180
>> ********** mpc83xx_setup_phy.182
>> ********** mpc83xx_usb_setup.238
>> ********** mpc83xx_usb_setup.245
>> ********** mpc83xx_usb_setup.249
>> ********** mpc83xx_usb_setup.251
>> ********** ehci_fsl_reinit.259
>> ********** ehci_hub_control.559 - req: 8961
>> ********** ehci_hub_control.574
>> ********** ehci_hub_control.559 - req: 8961
>> ********** ehci_hub_control.574
>> ********** ehci_fsl_reinit.261
>> ********** ehci_fsl_setup.301
>> fsl-ehci fsl-ehci.0: irq 39, io base 0xff022000
>> fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
>> usb usb1: configuration #1 chosen from 1 choice
>> hub 1-0:1.0: USB hub found
>> ********** ehci_hub_control.559 - req: 40966
>> ********** ehci_hub_control.637
>> hub 1-0:1.0: 2 ports detected
>> ********** ehci_hub_control.559 - req: 40960
>> ********** ehci_hub_control.642
>> ********** ehci_hub_control.559 - req: 8963
>> ********** ehci_hub_control.805
>> ********** ehci_hub_control.559 - req: 8963
>> ********** ehci_hub_control.805
>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> usb usb1: Product: Freescale On-Chip EHCI Host Controller
>> usb usb1: Manufacturer: Linux 2.6.28 ehci_hcd
>> usb usb1: SerialNumber: fsl-ehci.0
>> fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
>> fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
>> ********** ehci_fsl_setup.272
>> ********** ehci_fsl_setup.296
>> ********** ehci_fsl_setup.299
>> ********** ehci_fsl_reinit.257
>> ********** mpc83xx_usb_setup.192
>> ********** mpc83xx_usb_setup.207
>> ********** mpc83xx_usb_setup.215
>> ********** mpc83xx_setup_phy.163
>> ********** mpc83xx_setup_phy.180
>> MACHINE CHECK - so dead it can't even print the message!
>>
>> At this point, it should carry on like this:
>>
>> ********** ehci_hub_control.559 - req: 8963
>> ********** ehci_hub_control.805
>> ********** ehci_hub_control.559 - req: 41728
>> ********** ehci_hub_control.648
>> ********** ehci_hub_control.559 - req: 8961
>> ********** ehci_hub_control.574
>> usb 1-1: configuration #1 chosen from 1 choice
>> hub 1-1:1.0: USB hub found
>> hub 1-1:1.0: 4 ports detected
>> usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
>> usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
>> usb 1-1: Product: USB2.0 Hub
>> ********** ehci_hub_control.559 - req: 41728
>> ********** ehci_hub_control.648
>>
>> You can see that it successfully found the connected external HUB.
>>
>> Any ideas why this happens? This [basic] code used to work (2.6.20)
>> on both platforms. I know that's a long time ago, but MACHINE CHECK??
>>
>> (*) To get this platform to run 2.6.20, I had to patch the CPU tables
>> to recognize it as 8347 (kernels of that vintage relied on the SVR to
>> make choices, not PVR)
>>
>

-- 
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------