[PATCH/RFC] Document Freescale power management nodes, and the sleep property.
Scott Wood
scottwood at freescale.com
Wed Jun 25 05:21:54 EST 2008
Signed-off-by: Scott Wood <scottwood at freescale.com>
---
Documentation/powerpc/booting-without-of.txt | 192 ++++++++++++++++++++------
1 files changed, 151 insertions(+), 41 deletions(-)
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index b68684d..1aa59f8 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -62,6 +62,7 @@ Table of Contents
s) Freescale on board FPGA
t) Freescael MSI interrupt controller
u) Freescale General-purpose Timers Module
+ v) Freescale Power Management Controller
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
@@ -92,10 +93,12 @@ Table of Contents
3) OpenPIC Interrupt Controllers
4) ISA Interrupt Controllers
- VIII - Specifying GPIO information for devices
+ IX - Specifying GPIO information for devices
1) gpios property
2) gpio-controller nodes
+ X - Specifying device power management information (sleep property)
+
Appendix A - Sample SOC node for MPC8540
@@ -2967,6 +2970,60 @@ platforms are moved over to use the flattened-device-tree model.
clock-frequency = <0>;
};
+ v) Freescale Power Management Controller
+
+ Properties:
+ - compatible: "fsl,<chip>-pmc".
+
+ "fsl,mpc8349-pmc" should be listed for any chip whose PMC is
+ compatible. "fsl,mpc8313-pmc" should also be listed for any chip
+ whose PMC is compatible, and implies deep-sleep capability.
+
+ "fsl,mpc8548-pmc" should be listed for any chip whose PMC is
+ compatible. "fsl,mpc8536-pmc" should also be listed for any chip
+ whose PMC is compatible, and implies deep-sleep capability.
+
+ Compatibility does not include bit assigments in SCCR/PMCDR; these bit
+ assigments are indicated via the sleep specifier in each device's
+ sleep property.
+
+ - reg: For devices compatible with "fsl,mpc8349-pmc", the first resource
+ is the PMC block, and the second resource is the Clock Configuration
+ block.
+
+ For devices compatible with "fsl,mpc8548-pmc", the first resource
+ is a 32-byte block beginning with DEVDISR.
+
+ - interrupts: For "fsl,mpc8349-pmc"-compatible devices, the first
+ resource is the PMC block interrupt.
+
+ Sleep specifiers:
+
+ fsl,mpc8349-pmc: Sleep specifiers consist of one cell. For each bit
+ that is set in the cell, the corresponding bit in SCCR will be saved
+ and cleared on suspend, and restored on resume. This sleep controller
+ supports disabling and resuming devices at any time.
+
+ fsl,mpc8536-pmc: Sleep specifiers consist of two cells, the second of
+ which will be ORed into PMCDR upon suspend, and cleared from PMCDR
+ upon resume. The first cell is as described for fsl,mpc8578-pmc.
+ This sleep controller only supports disabling devices during system
+ sleep, or permanently.
+
+ fsl,mpc8548-pmc: Sleep specifiers consist of one cell, which will be
+ ORed into DEVDISR upon a request for permanent device disabling. This
+ sleep controller does not support configuring devices to disable
+ during system sleep (unless supported by another compatible match), or
+ dynamically.
+
+ Example:
+
+ power at b00 {
+ compatible = "fsl,mpc8313-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 8>;
+ };
+
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
@@ -3574,8 +3631,8 @@ encodings listed below:
2 = high to low edge sensitive type enabled
3 = low to high edge sensitive type enabled
-VIII - Specifying GPIO information for devices
-==============================================
+IX - Specifying GPIO information for devices
+============================================
1) gpios property
-----------------
@@ -3623,6 +3680,37 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
gpio-controller;
};
+X - Specifying Device Power Management Information (sleep property)
+===================================================================
+
+Devices on SOCs often have mechanisms for placing devices into low-power
+states that are decoupled from the devices' own register blocks. Sometimes,
+this information is more complicated than a cell-index property can
+reasonably describe. Thus, each device controlled in such a manner
+may contain a "sleep" property which describes these connections.
+
+The sleep property consists of one or more sleep resources, each of
+which consists of a phandle to a sleep controller, followed by a
+controller-specific sleep specifier of zero or more cells.
+
+The semantics of what type of low power modes are possible are defined
+by the sleep controller. Some examples of the types of low power modes
+that may be supported are:
+
+ - Dynamic: The device may be disabled or enabled at any time.
+ - System Suspend: The device may request to be disabled or remain
+ awake during system suspend, but will not be disabled until then.
+ - Permanent: The device is disabled permanently (until the next hard
+ reset).
+
+Some devices may share a clock domain with each other, such that they should
+only be suspended when none of the devices are in use. Where reasonable,
+such nodes should be placed on a virtual bus, where the bus has the sleep
+property. If the clock domain is shared among devices that cannot be
+reasonably grouped in this manner, then create a virtual sleep controller
+(similar to an interrupt nexus, except that defining a standardized
+sleep-map should wait until its necessity is demonstrated).
+
Appendix A - Sample SOC node for MPC8540
========================================
@@ -3639,47 +3727,47 @@ not necessary as they are usually the same as the root node.
reg = <e0000000 00003000>;
bus-frequency = <0>;
- mdio at 24520 {
- reg = <24520 20>;
- device_type = "mdio";
- compatible = "gianfar";
-
- ethernet-phy at 0 {
- linux,phandle = <2452000>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy at 1 {
- linux,phandle = <2452001>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy at 3 {
- linux,phandle = <2452002>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
-
- };
-
ethernet at 24000 {
#size-cells = <0>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <24000 1000>;
mac-address = [ 00 E0 0C 00 73 00 ];
interrupts = <d 3 e 3 12 3>;
interrupt-parent = <40000>;
phy-handle = <2452000>;
+ sleep = <&pmc 00000080>;
+ ranges;
+
+ mdio at 24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy at 0 {
+ linux,phandle = <2452000>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ ethernet-phy at 1 {
+ linux,phandle = <2452001>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ ethernet-phy at 3 {
+ linux,phandle = <2452002>
+ interrupt-parent = <40000>;
+ interrupts = <35 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
};
ethernet at 25000 {
@@ -3693,6 +3781,7 @@ not necessary as they are usually the same as the root node.
interrupts = <13 3 14 3 18 3>;
interrupt-parent = <40000>;
phy-handle = <2452001>;
+ sleep = <&pmc 00000040>;
};
ethernet at 26000 {
@@ -3706,15 +3795,31 @@ not necessary as they are usually the same as the root node.
interrupts = <19 3>;
interrupt-parent = <40000>;
phy-handle = <2452002>;
+ sleep = <&pmc 00000020>;
};
serial at 4500 {
- device_type = "serial";
- compatible = "ns16550";
- reg = <4500 100>;
- clock-frequency = <0>;
- interrupts = <1a 3>;
- interrupt-parent = <40000>;
+ compatible = "fsl,mpc8540-duart", "simple-bus";
+ sleep = <&pmc 00000002>;
+ ranges;
+
+ serial at 4500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4500 100>;
+ clock-frequency = <0>;
+ interrupts = <1a 3>;
+ interrupt-parent = <40000>;
+ };
+
+ serial at 4600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <4500 100>;
+ clock-frequency = <0>;
+ interrupts = <1a 3>;
+ interrupt-parent = <40000>;
+ };
};
pic at 40000 {
@@ -3733,6 +3838,11 @@ not necessary as they are usually the same as the root node.
device_type = "i2c";
compatible = "fsl-i2c";
dfsrr;
+ sleep = <&pmc 00000004>;
};
+ pmc: power at e0070 {
+ compatible = "fsl,mpc8540-pmc", "fsl,mpc8548-pmc";
+ reg = <e0070 20>;
+ };
};
--
1.5.5.4
More information about the Linuxppc-dev
mailing list