[PATCH] Fix definitions for dbcr0, dbcr1, & dbcr2 register for bookE processors

[Josh Boyer]

On Wed, 04 Jun 2008 17:26:44 -0500
Jerone Young <jyoung5 at us.ibm.com> wrote:

> Taken from the PowerPC ISA BookIII-E specifies that DBCR0 is different
> for all others that are not ppc405 chips. So I have now chnaged the
> conditional to reflect this. Also added definitions needed for DBCR1 &
> DBCR2.

Interesting.  The only uses of these bit definitions happen to be for
IDM and IC, which match across 440 and 405.  Overall, the patch is
needed.  A few minor nits below.

> 
> Signed-off-by: Jerone Young <jyoung5 at us.ibm.com>
> 
> diff --git a/include/asm-powerpc/reg_booke.h b/include/asm-powerpc/reg_booke.h
> --- a/include/asm-powerpc/reg_booke.h
> +++ b/include/asm-powerpc/reg_booke.h
> @@ -253,6 +253,7 @@
>  #define ESR_BO		0x00020000	/* Byte Ordering */
> 
>  /* Bit definitions related to the DBCR0. */
> +#if defined(CONFIG_40x)
>  #define DBCR0_EDM	0x80000000	/* External Debug Mode */
>  #define DBCR0_IDM	0x40000000	/* Internal Debug Mode */
>  #define DBCR0_RST	0x30000000	/* all the bits in the RST field */
> @@ -275,6 +276,46 @@
>  #define DBCR0_IA12T	0x00008000	/* Instr Addr 1-2 range Toggle */
>  #define DBCR0_IA34T	0x00004000	/* Instr Addr 3-4 range Toggle */
>  #define DBCR0_FT	0x00000001	/* Freeze Timers on debug event */
> +#elif defined(CONFIG_BOOKE)
> +#define DBCR0_EDM	0x80000000	/* External Debug Mode */
> +#define DBCR0_IDM	0x40000000	/* Internal Debug Mode */
> +#define DBCR0_RST	0x30000000	/* all the bits in the RST field */
> +#define DBCR0_RST_SYSTEM 0x30000000	/* System Reset */
> +#define DBCR0_RST_CHIP	0x20000000	/* Chip Reset */
> +#define DBCR0_RST_CORE	0x10000000	/* Core Reset */
> +#define DBCR0_RST_NONE	0x00000000	/* No Reset */
> +#define DBCR0_IC	0x08000000	/* Instruction Completion */
> +#define DBCR0_BT	0x04000000	/* Branch Taken */
> +#define DBCR0_EDE	0x02000000	/* Exception Debug Event */
> +#define DBCR0_TDE	0x01000000	/* TRAP Debug Event */
> +#define DBCR0_IA1	0x00800000	/* Instr Addr compare 1 enable */
> +#define DBCR0_IA2	0x00400000	/* Instr Addr compare 2 enable */
> +#define DBCR0_IA3	0x00200000	/* Instr Addr compare 3 enable */
> +#define DBCR0_IA4	0x00100000	/* Instr Addr compare 4 enable */
> +#define DBCR0_DAC1R	0x00080000	/* DAC 1 Read enable */
> +#define DBCR0_DAC1W	0x00040000	/* DAC 1 Write enable */
> +#define DBCR0_DAC2R	0x00020000	/* DAC 2 Read enable */
> +#define DBCR0_DAC2W	0x00010000	/* DAC 2 Write enable */
> +#define DBCR0_RET	0x00008000	/* Return Debug Event */
> +#define DBCR0_FT	0x00000001	/* Freeze Timers on debug event */
> +#endif
> +
> +/* Bit definitions related to the DBCR1. */
> +#if defined(CONFIG_BOOKE)
> +#define DBCR1_IA12	0x00800000	/* Instr Addr 1-2 range enable */
> +#define DBCR1_IA12X	0x00C00000	/* Instr Addr 1-2 range eXclusive */
> +#define DBCR1_IA12T	0x00010000	/* Instr Addr 1-2 range Toggle */
> +#define DBCR1_IA34	0x00000080	/* Instr Addr 3-4 range enable */
> +#define DBCR1_IA34X	0x000000C0	/* Instr Addr 3-4 range eXclusive */
> +#define DBCR1_IA34T	0x00000001	/* Instr Addr 3-4 range Toggle */
> +#endif
> +
> +/* Bit definitions related to the DBCR2. */
> +#if defined(CONFIG_BOOKE)
> +#define DBCR2_DAC12	0x00800000	/* DAC 1-2 range enable */
> +#define DBCR2_DAC12X	0x00C00000	/* DAC 1-2 range eXclusive */
> +#define DBCR2_DAC12A	0x00200000	/* DAC 1-2 Asynchronous */
> +#endif

You can collapse these definition into one #if defined(CONFIG_BOOKE)
block.  No need for two.

Also, 405 has DBCR1.  Think you could provide the definitions for 405
while you're at it?

josh