[RFC POWERPC] booting-without-of: bindings for FHCI USB, GPIO LEDs, MCU, and NAND on UPM

[Laurent Pinchart]

Hi Anton,

On Tuesday 22 April 2008 21:41, Anton Vorontsov wrote:
> Hi all,
> 
> Here is purposed bindings draft for the new drivers that I would like to
> send for this or next merge window, depending on results of this RFC. ;-)
> (The new bindings needs to be in-tree or at least Acked before I could
> send the drivers.)
> 
> Comments and suggestions are highly appreciated.
> 
> Thanks.
> 
> diff --git a/Documentation/powerpc/booting-without-of.txt 
b/Documentation/powerpc/booting-without-of.txt
> index c350623..38fe3e9 100644
> --- a/Documentation/powerpc/booting-without-of.txt
> +++ b/Documentation/powerpc/booting-without-of.txt
> @@ -59,6 +59,11 @@ Table of Contents
>        p) Freescale Synchronous Serial Interface
>        q) USB EHCI controllers
>        r) Freescale General-purpose Timers Module
> +      s) Freescale USB Parameter RAM:
> +      t) Freescale QUICC Engine USB Controller
> +      u) LEDs on GPIOs
> +      v) Freescale MCU with MPC8349E-mITX compatible firmware
> +      w) NAND on UPM-driven Freescale Localbus
>  
>    VII - Marvell Discovery mv64[345]6x System Controller chips
>      1) The /system-controller node
> @@ -2866,6 +2871,139 @@ platforms are moved over to use the 
flattened-device-tree model.
>      	clock-frequency = <0>;
>      };
>  
> +    s) Freescale USB Parameter RAM:
> +
> +    Required properties:
> +      - compatible : should be "fsl,<chip>-qe-muram-usb-pram",
> +        "fsl,qe-muram-usb-pram", "fsl,cpm-muram-usb-pram".
> +      - reg : should contain USB PRAM location and length.
> +
> +    Example:
> +
> +	usb-pram at 8b00 {
> +		compatible = "fsl,mpc8360-qe-muram-usb-pram",
> +			     "fsl,qe-muram-usb-pram",
> +			     "fsl,cpm-muram-usb-pram";
> +		reg = <0x8b00 0x100>;
> +	};
> +
> +    t) Freescale QUICC Engine USB Controller
> +
> +    Required properties:
> +      - compatible : should be "fsl,<chip>-qe-usb", "fsl,qe-usb",
> +        "fsl,usb-fhci"
> +      - reg : should contain gtm registers location and length.
> +      - interrupts : should contain USB interrupt.
> +      - interrupt-parent : interrupt source phandle.
> +      - fsl,fullspeed-clock : specifies the full speed USB clock source.
> +      - fsl,lowspeed-clock : specifies the low speed USB clock source.
> +      - fsl,usb-mode : should be "host".
> +      - linux,hub-power-budget : optional, USB power budget for the root 
hub
> +        in mA.
> +      - gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, 
USBRP,
> +        USBRN, SPEED (optional), and SUSPEND (optional).

Suspend should in my opinion be renamed power (or bus power or anything 
similar), as it controls the USB power and not USB PHY sleep mode.

> +    Example:
> +
> +	usb at 6c0 {
> +		compatible = "fsl,mpc8360-qe-usb", "fsl,qe-usb",
> +			     "fsl,usb-fhci";
> +		reg = <0x6c0 0x40>;
> +		interrupts = <11>;
> +		interrupt-parent = <&qeic>;
> +		fsl,fullspeed-clock = "clk21";
> +		fsl,usb-mode = "host";
> +		gpios = <&qe_pio_b  2 0 /* USBOE */
> +			 &qe_pio_b  3 0 /* USBTP */
> +			 &qe_pio_b  8 0 /* USBTN */
> +			 &qe_pio_b  9 0 /* USBRP */
> +			 &qe_pio_b 11 0 /* USBRN */
> +			 &qe_pio_e 20 0 /* SPEED */
> +			 &qe_pio_e 21 0 /* SUSPN */>;
> +	};
> +
> +    u) LEDs on GPIOs
> +
> +    Required properties:
> +      - compatible : should be "linux,gpio-led".
> +      - linux,name : LED name.
> +      - linux,active-low : property should be present if LED wired as
> +        active-low.

Just thinking out loud, wasn't the third GPIO cell supposed to be used to 
encode such properties ?

> +      - linux,default-trigger : Linux default trigger for this LED.
> +      - linux,brightness : default brightness.
> +      - gpios : should specify LED GPIO.
> +
> +    Example:
> +
> +	led at 0 {
> +		compatible = "linux,gpio-led";
> +		linux,name = "pwr";
> +		linux,brightness = <1>;
> +		linux,active-low;
> +		gpios = <&mcu_pio 0>;
> +	};
> +
> +	led at 1 {
> +	        compatible = "linux,gpio-led";
> +	        linux,name = "hdd";
> +	        linux,default-trigger = "ide-disk";
> +		linux,active-low;
> +		gpios = <&mcu_pio 1>;
> +	};

[snip]

-- 
Laurent Pinchart
CSE Semaphore Belgium

Chaussee de Bruxelles, 732A
B-1410 Waterloo
Belgium

T +32 (2) 387 42 59
F +32 (2) 387 42 75
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: not available
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20080423/48281181/attachment.pgp>