EMAC OF binding....
Benjamin Herrenschmidt
benh at au1.ibm.com
Mon Jan 8 17:09:18 EST 2007
Ok, so now that I have a new EMAC driver that seems to work reasonably
well on Axon using OF devices, I can give you guys a proper list of the
properties it expects in the device-tree to be discussed here. We need
to finalize a firmware soon so I would appreciate feedback if any ASAP.
The definitions below aren't 100% matching the driver I posted earlier,
I'll post a new driver soon.
* The OPB node needs a "clock-frequency" property
* In the EMAC node itself (plb5/plb4/opb/ethernet)
- name : "ethernet"
- device_type : "network"
- compatible : compatible list, contains 2 entries, first is "emac-CHIP" where
CHIP is the host ASIC (440gx, 405gp, axon) and second is either
"emac" or "emac4".
For axon, thus, we have: "emac-axon","emac4"
- model : optional model string
- interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
- interrupt-parent : optional, if needed for interrupt mapping
- reg : <registers mapping>
- local-mac-address : 6 bytes, MAC address
- mal-device : 1 cell, phandle of the associated McMAL node
- mal-tx-channel : 1 cell, index of the tx channel on McMAL associated with this EMAC
- mal-rx-channel : 1 cell, index of the rx channel on McMAL associated with this EMAC
- cell-index : 1 cell, hardware index of the EMAC cell on a given ASIC (typically
0x00000000 and 0x00000001 for EMAC-0 and EMAC-1 on each Axon chip)
- max-mtu : 1 cell, maximum MTU supported in bytes
- rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec operations.
For axon, 2048
- rx-fifo-size-gige : 1 cell, optional, Rx fifo size in bytes for 1000 Mb/sec operations
(if absent the value is the same as rx-fifo-size).
For axon, either absent or 2048.
- tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec operations. For axon
- tx-fifo-size-gige : 1 cell, optional, Tx fifo size in bytes for 1000 Mb/sec operations
(if absent the value is the same as tx-fifo-size)
For axon, either absent or 2048.
- fifo-entry-size : 1 cell, size of a fifo entry (used to calculate thresholds)
For axon, 0x00000010
- mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
- phy-mode : 1 cell, Mode of operations of the PHY interface:
#define PHY_MODE_NA 0
#define PHY_MODE_MII 1
#define PHY_MODE_RMII 2
#define PHY_MODE_SMII 3
#define PHY_MODE_RGMII 4
#define PHY_MODE_TBI 5
#define PHY_MODE_GMII 6
#define PHY_MODE_RTBI 7
#define PHY_MODE_SGMII 8
For axon, it is PHY_MODE_RGMII
- phy-address : 1 cell, optional, MDIO address of the PHY. If absent, a search
is performed
For axon: please fill with approriate value, I don't have it at
hand, it depends on the board and the EMAC of course.
- phy-map : 1 cell, optional, bitmap of addresses to probe the PHY for, used
if phy-address is absent. bit 0x00000001 is MDIO address 0. For axon
it can be absent, thouugh my current driver doesn't handle phy-address
yet so for now, keep 0x00ffffff in it.
- mdio-device : 1 cell, optional. If shared MDIO registers (440EP), phandle of the EMAC
to use to drive the MDIO lines for the PHY used by this EMAC.
For axon: absent
- zmii-device : 1 cell, optional. If connected to a ZMII, phandle of the ZMII device node
For axon: absent
- zmii-channel : 1 cell, optional. If connected to a ZMII, which channel or 0xffffffff if
ZMII is only used for MDIO
- rgmii-device : 1 cell, optional. If connected to a RGMII, phandle of the RGMII device node
For axon: phandle of plb5/plb4/opb/rgmii
- rgmii-channel : 1 cell, optional. If connected to a RGMII, which channel
Fox axon: present, whatever value is appropriate for each EMAC, that is
the content of the current (bogus) "phy-port" property
- tah-device : 1 cell, optional. If connected to a TAH engine for offload, phandle of
the TAH device node
- tah-channel : 1 cell, optional. If appropriate, channel used on the TAH engine
* In the McMAL node
- name : "mcmal"
- device_type : "mcmal-dma"
- compatible : compatible list, containing 2 entries, first is "mcmal-CHIP" where
CHIP is the hose ASIC (like emac) and the second is either "mcmal"
or "mcmal2".
: For axon, "mcmal-axon","mcmal2"
- model : optional model string
- interrupts : <interrupt mapping for the MAL interrupts sources:
5 sources: tx_eob, rx_eob, serr, txde, rxde>.
For axon: This is _different_ from the current firmware. We use
the "delayed" interrupts for txeob and rxeob. Thus we end up with
mapping those 5 MPIC interrupts, all level positive sensitive:
10, 11, 32, 33, 34 (in decimal)
- dcr-reg : < DCR registers range >
- dcr-parent : if needed for dcr-reg
- num-tx-chans : 1 cell, number of Tx channels
- num-rx-chans : 1 cell, number of Rx channels
* In the ZMII node
- name : "zmii"
- device_type : "zmii"
- compatible : compatible list, containing 2 entries, first is "zmii-CHIP" where
CHIP is the hose ASIC (like emac) and the second is "zmii"
: For axon, "zmii-axon","zmii"
- model : optional model string
- reg : <registers mapping>
* In the RGMII node
- name : "rgmii"
- device_type : "rgmii"
- compatible : compatible list, containing 2 entries, first is "rgmii-CHIP" where
CHIP is the hose ASIC (like emac) and the second is "rgmii"
: For axon, "rgmii-axon","rgmii"
- model : optional model string
- reg : <registers mapping>
- revision : as provided by the RGMII new version register if available
For axon: 0x0000012a
Ben.
More information about the Linuxppc-dev
mailing list