[PATCH/2.6.17-rc4 8/10] Add tsi108 8250 serial support

[Russell King]

On Thu, May 18, 2006 at 12:00:43PM +0800, Zang Roy-r61911 wrote:
> 
> -----Original Message-----
> From: Kumar Gala [mailto:galak at kernel.crashing.org]
> Sent: 2006???5???17??? 21:26
> To: Zang Roy-r61911
> Cc: Paul Mackerras; linuxppc-dev list; Alexandre.Bounine at tundra.com; Yang Xin-Xin-r48390
> Subject: Re: [PATCH/2.6.17-rc4 8/10] Add tsi108 8250 serial support
> 
> 
> 
> On May 17, 2006, at 5:14 AM, Zang Roy-r61911 wrote:
> 
> > This patch contains changes to the serial device driver specific  
> > for integrated
> > serial port in Tsi108 Host Bridge.

There's no explaination about why this is required.  What is the problem?
Which changes relate directly to this problem and which changes are
related to fixing some other issue not related to the errata?

Plus, every patch line is prefixed by "> "... patch doesn't like that.

> >
> > Signed-off-by: Alexandre Bounine <alexandreb at tundra.com>
> > Signed-off-by: Roy Zang	<tie-fei.zang at freescale.com>
> >
> >> From nobody Mon Sep 17 00:00:00 2001
> > From: roy zang <tie-fei.zang at freescale.com>
> > Date: Tue May 16 15:26:02 2006 +0800
> > Subject: [PATCH] Add tsi108 serial support
> 
> This patch needs to go to Russell King as uart/8250 driver maintainer.
> 
> - kumar
> 
> >
> > ---
> >
> >  drivers/serial/8250.c |   17 +++++++++++++++++
> >  1 files changed, 17 insertions(+), 0 deletions(-)
> >
> > 6cb950357e9970afa671d59f172dbc4b03f11560
> > diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
> > index bbf78aa..c12f516 100644
> > --- a/drivers/serial/8250.c
> > +++ b/drivers/serial/8250.c
> > @@ -723,7 +723,9 @@ static int broken_efr(struct uart_8250_p
> >  static void autoconfig_16550a(struct uart_8250_port *up)
> >  {
> >  	unsigned char status1, status2;
> > +#ifndef CONFIG_TSI108_BRIDGE
> >  	unsigned int iersave;
> > +#endif
> >
> >  	up->port.type = PORT_16550A;
> >  	up->capabilities |= UART_CAP_FIFO;
> > @@ -833,6 +835,7 @@ static void autoconfig_16550a(struct uar
> >  	 * trying to write and read a 1 just to make sure it's not
> >  	 * already a 1 and maybe locked there before we even start start.
> >  	 */
> > +#ifndef CONFIG_TSI108_BRIDGE
> >  	iersave = serial_in(up, UART_IER);
> >  	serial_outp(up, UART_IER, iersave & ~UART_IER_UUE);
> >  	if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
> > @@ -859,6 +862,7 @@ static void autoconfig_16550a(struct uar
> >  		DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
> >  	}
> >  	serial_outp(up, UART_IER, iersave);
> > +#endif
> >  }
> >
> >  /*
> > @@ -1348,7 +1352,12 @@ static irqreturn_t serial8250_interrupt(
> >
> >  		up = list_entry(l, struct uart_8250_port, list);
> >
> > +#ifdef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> > +		/* read IIR as part of 32-bit word */
> > +		iir = (in_be32((u32 *)(up->port.membase + UART_RX)) >> 8) & 0xff;
> > +#else
> >  		iir = serial_in(up, UART_IIR);
> > +#endif
> >  		if (!(iir & UART_IIR_NO_INT)) {
> >  			serial8250_handle_port(up, regs);
> >
> > @@ -1529,7 +1538,9 @@ static int serial8250_startup(struct uar
> >  {
> >  	struct uart_8250_port *up = (struct uart_8250_port *)port;
> >  	unsigned long flags;
> > +#ifndef CONFIG_TSI108_BRIDGE
> >  	unsigned char lsr, iir;
> > +#endif
> >  	int retval;
> >
> >  	up->capabilities = uart_config[up->port.type].flags;
> > @@ -1567,7 +1578,9 @@ #endif
> >  	 */
> >  	(void) serial_inp(up, UART_LSR);
> >  	(void) serial_inp(up, UART_RX);
> > +#ifndef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> >  	(void) serial_inp(up, UART_IIR);
> > +#endif
> >  	(void) serial_inp(up, UART_MSR);
> >
> >  	/*
> > @@ -1634,6 +1647,7 @@ #endif
> >
> >  	serial8250_set_mctrl(&up->port, up->port.mctrl);
> >
> > +#ifndef CONFIG_TSI108_BRIDGE
> >  	/*
> >  	 * Do a quick test to see if we receive an
> >  	 * interrupt when we enable the TX irq.
> > @@ -1652,6 +1666,7 @@ #endif
> >  	} else {
> >  		up->bugs &= ~UART_BUG_TXEN;
> >  	}
> > +#endif
> >
> >  	spin_unlock_irqrestore(&up->port.lock, flags);
> >
> > @@ -1678,7 +1693,9 @@ #endif
> >  	 */
> >  	(void) serial_inp(up, UART_LSR);
> >  	(void) serial_inp(up, UART_RX);
> > +#ifndef CONFIG_TSI108_BRIDGE /* for TSI108_REV_Z1 errata U2 */
> >  	(void) serial_inp(up, UART_IIR);
> > +#endif
> >  	(void) serial_inp(up, UART_MSR);
> >
> >  	return 0;
> > -- 
> > 1.3.0
> > _______________________________________________
> > Linuxppc-dev mailing list
> > Linuxppc-dev at ozlabs.org
> > https://ozlabs.org/mailman/listinfo/linuxppc-dev

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:  2.6 Serial core