[PATCH 2/2] ARM: dts: aspeed: Minerva: Add Facebook Minerva CMC board

[Yang Chen]

Hi Krzysztof,

> +
> +&i2c15 {
> +     status = "okay";
> +
> +     eeprom at 50 {
> +             compatible = "atmel,24c128";
> +             reg = <0x50>;
> +     };
> +};
> +
> +&adc0 {
> +     ref_voltage = <2500>;

There is no such property in the bindings.

> +     status = "okay";
> +     pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> +             &pinctrl_adc2_default &pinctrl_adc3_default
> +             &pinctrl_adc4_default &pinctrl_adc5_default
> +             &pinctrl_adc6_default &pinctrl_adc7_default>;
> +};
> +
> +&adc1 {
> +     ref_voltage = <2500>;

NAK, there is no such property.

Thanks for your advice, I will change this property to
"aspeed,int-vref-microvolt" which is defined in the binding in the v2 patch.

Thanks,
Yang Chen


Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org> 於 2023年9月13日 週三
下午6:04寫道：

> On 12/09/2023 16:05, yangchen.openbmc at gmail.com wrote:
> > From: Yang Chen <yangchen.openbmc at gmail.com>
> >
> > Add linux device tree entry related to the Minerva Chassis Management
> > Controller (CMC) specific devices connected to the Aspeed SoC (AST2600).
> >
> > Signed-off-by: Yang Chen <yangchen.openbmc at gmail.com>
> > ---
> >  arch/arm/boot/dts/aspeed/Makefile             |   1 +
> >  .../aspeed-bmc-facebook-minerva-cmc.dts       | 265 ++++++++++++++++++
> >  2 files changed, 266 insertions(+)
> >  create mode 100644
> arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva-cmc.dts
> >
> > diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/
>
>
> > +
> > +&i2c15 {
> > +     status = "okay";
> > +
> > +     eeprom at 50 {
> > +             compatible = "atmel,24c128";
> > +             reg = <0x50>;
> > +     };
> > +};
> > +
> > +&adc0 {
> > +     ref_voltage = <2500>;
>
> There is no such property in the bindings.
>
> > +     status = "okay";
> > +     pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> > +             &pinctrl_adc2_default &pinctrl_adc3_default
> > +             &pinctrl_adc4_default &pinctrl_adc5_default
> > +             &pinctrl_adc6_default &pinctrl_adc7_default>;
> > +};
> > +
> > +&adc1 {
> > +     ref_voltage = <2500>;
>
> NAK, there is no such property.
>
>
>
> Best regards,
> Krzysztof
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/linux-aspeed/attachments/20230913/68c9c87b/attachment-0001.htm>