[PATCH v3 3/3] i3c: ast2600: Add AST2600 platform-specific driver

Zbigniew, Lukwinski zbigniew.lukwinski at linux.intel.com
Fri Apr 28 08:00:36 AEST 2023


On 3/31/2023 11:15 AM, Jeremy Kerr wrote:
> Now that we have platform-specific infrastructure for the dw i3c driver,
> add platform support for the ASPEED AST2600 SoC.
>
> The AST2600 has a small set of "i3c global" registers, providing
> platform-level i3c configuration outside of the i3c core.
>
> For the ast2600, we need a couple of extra setup operations:
>
>   - on probe: find the i3c global register set and parse the SDA pullup
>     resistor values
>
>   - on init: set the pullups accordingly, and set the i3c instance IDs
>
> Signed-off-by: Jeremy Kerr<jk at codeconstruct.com.au>
>
> ---
> v2:
>   - use new dw platform infrastructure
> v3:
>   - switch to embedded struct for platform data
>   - drop of_match_ptr()
> ---
>   MAINTAINERS                             |   6 +
>   drivers/i3c/master/Kconfig              |  14 ++
>   drivers/i3c/master/Makefile             |   1 +
>   drivers/i3c/master/ast2600-i3c-master.c | 168 ++++++++++++++++++++++++
>   4 files changed, 189 insertions(+)
>   create mode 100644 drivers/i3c/master/ast2600-i3c-master.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index bd8ebc25afcf..ecadd5ccf771 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9714,6 +9714,12 @@ S:	Orphan
>   F:	Documentation/devicetree/bindings/i3c/snps,dw-i3c-master.yaml
>   F:	drivers/i3c/master/dw*
>   
> +I3C DRIVER FOR ASPEED AST2600
> +M:	Jeremy Kerr<jk at codeconstruct.com.au>
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/i3c/aspeed,ast2600-i3c.yaml
> +F:	drivers/i3c/master/ast2600-i3c-master.c
> +
>   I3C SUBSYSTEM
>   M:	Alexandre Belloni<alexandre.belloni at bootlin.com>
>   L:	linux-i3c at lists.infradead.org  (moderated for non-subscribers)
> diff --git a/drivers/i3c/master/Kconfig b/drivers/i3c/master/Kconfig
> index 3b8f95916f46..90dee3ec5520 100644
> --- a/drivers/i3c/master/Kconfig
> +++ b/drivers/i3c/master/Kconfig
> @@ -22,6 +22,20 @@ config DW_I3C_MASTER
>   	  This driver can also be built as a module.  If so, the module
>   	  will be called dw-i3c-master.
>   
> +config AST2600_I3C_MASTER
> +	tristate "ASPEED AST2600 I3C master driver"
> +	depends on DW_I3C_MASTER
> +	depends on ARCH_ASPEED || COMPILE_TEST
> +	select MFD_SYSCON
> +	help
> +	  Support for ASPEED AST2600 I3C Controller.
> +
> +	  This hardware is an instance of the DW I3C controller; this
> +	  driver adds platform- specific support for AST2600 hardware.
> +
> +	  This driver can also be built as a module.  If so, the module
> +	  will be called ast2600-i3c-master.
> +
>   config SVC_I3C_MASTER
>   	tristate "Silvaco I3C Dual-Role Master driver"
>   	depends on I3C
> diff --git a/drivers/i3c/master/Makefile b/drivers/i3c/master/Makefile
> index b3fee0f690b2..3e97960160bc 100644
> --- a/drivers/i3c/master/Makefile
> +++ b/drivers/i3c/master/Makefile
> @@ -1,5 +1,6 @@
>   # SPDX-License-Identifier: GPL-2.0-only
>   obj-$(CONFIG_CDNS_I3C_MASTER)		+= i3c-master-cdns.o
>   obj-$(CONFIG_DW_I3C_MASTER)		+= dw-i3c-master.o
> +obj-$(CONFIG_AST2600_I3C_MASTER)	+= ast2600-i3c-master.o
>   obj-$(CONFIG_SVC_I3C_MASTER)		+= svc-i3c-master.o
>   obj-$(CONFIG_MIPI_I3C_HCI)		+= mipi-i3c-hci/
> diff --git a/drivers/i3c/master/ast2600-i3c-master.c b/drivers/i3c/master/ast2600-i3c-master.c
> new file mode 100644
> index 000000000000..d265669c04f1
> --- /dev/null
> +++ b/drivers/i3c/master/ast2600-i3c-master.c
> @@ -0,0 +1,168 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023 Code Construct
> + *
> + * Author: Jeremy Kerr<jk at codeconstruct.com.au>
> + */
> +
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include "dw-i3c-master.h"
> +
> +/* AST2600-specific global register set */
> +#define AST2600_I3CG_REG0(idx)	(((idx) * 4 * 4) + 0x10)
> +#define AST2600_I3CG_REG1(idx)	(((idx) * 4 * 4) + 0x14)
> +
> +#define AST2600_I3CG_REG0_SDA_PULLUP_EN_MASK	GENMASK(29, 28)
> +#define AST2600_I3CG_REG0_SDA_PULLUP_EN_2K	(0x0 << 28)
> +#define AST2600_I3CG_REG0_SDA_PULLUP_EN_750	(0x2 << 28)
> +
> +#define AST2600_I3CG_REG1_I2C_MODE		BIT(0)
> +#define AST2600_I3CG_REG1_TEST_MODE		BIT(1)
> +#define AST2600_I3CG_REG1_ACT_MODE_MASK		GENMASK(3, 2)
> +#define AST2600_I3CG_REG1_ACT_MODE(x)		(((x) << 2) & AST2600_I3CG_REG1_ACT_MODE_MASK)
> +#define AST2600_I3CG_REG1_PENDING_INT_MASK	GENMASK(7, 4)
> +#define AST2600_I3CG_REG1_PENDING_INT(x)	(((x) << 4) & AST2600_I3CG_REG1_PENDING_INT_MASK)
> +#define AST2600_I3CG_REG1_SA_MASK		GENMASK(14, 8)
> +#define AST2600_I3CG_REG1_SA(x)			(((x) << 8) & AST2600_I3CG_REG1_SA_MASK)
> +#define AST2600_I3CG_REG1_SA_EN			BIT(15)
> +#define AST2600_I3CG_REG1_INST_ID_MASK		GENMASK(19, 16)
> +#define AST2600_I3CG_REG1_INST_ID(x)		(((x) << 16) & AST2600_I3CG_REG1_INST_ID_MASK)
> +
> +#define AST2600_DEFAULT_SDA_PULLUP_OHMS		2000
> +
> +struct ast2600_i3c {
> +	struct dw_i3c_master dw;
> +	struct regmap *global_regs;
> +	unsigned int global_idx;
> +	unsigned int sda_pullup;
> +};
> +
> +static struct ast2600_i3c *to_ast2600_i3c(struct dw_i3c_master *dw)
> +{
> +	return container_of(dw, struct ast2600_i3c, dw);
> +}
> +
> +static int ast2600_i3c_pullup_to_reg(unsigned int ohms, u32 *regp)
> +{
> +	u32 reg;
> +
> +	switch (ohms) {
> +	case 2000:
> +		reg = AST2600_I3CG_REG0_SDA_PULLUP_EN_2K;
> +		break;
> +	case 750:
> +		reg = AST2600_I3CG_REG0_SDA_PULLUP_EN_750;
> +		break;
> +	case 545:
> +		reg = AST2600_I3CG_REG0_SDA_PULLUP_EN_2K |
> +			AST2600_I3CG_REG0_SDA_PULLUP_EN_750;

It does not work. To enable PullUp=545R you need to set both 28 and 29 
bit (0x*3*0000000) but '/AST2600_I3CG_REG0_SDA_PULLUP_EN_2K | 
AST2600_I3CG_REG0_SDA_PULLUP_EN_750/' is in fact 0x*2*0000000. Maybe you 
could consider adding extra macro 'AST2600_I3CG_REG0_SDA_PULLUP_EN_545' 
= (0x3 << 28)?


> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	if (regp)
> +		*regp = reg;
> +
> +	return 0;
> +}
> +
> +static int ast2600_i3c_init(struct dw_i3c_master *dw)
> +{
> +	struct ast2600_i3c *i3c = to_ast2600_i3c(dw);
> +	u32 reg = 0;
> +	int rc;
> +
> +	/* reg0: set SDA pullup values */
> +	rc = ast2600_i3c_pullup_to_reg(i3c->sda_pullup, &reg);
> +	if (rc)
> +		return rc;
> +
> +	rc = regmap_write(i3c->global_regs,
> +			  AST2600_I3CG_REG0(i3c->global_idx), reg);
> +	if (rc)
> +		return rc;
> +
> +	/* reg1: set up the instance id, but leave everything else disabled,
> +	 * as it's all for client mode
> +	 */
> +	reg = AST2600_I3CG_REG1_INST_ID(i3c->global_idx);
> +	rc = regmap_write(i3c->global_regs,
> +			  AST2600_I3CG_REG1(i3c->global_idx), reg);
> +
> +	return rc;
> +}
> +
> +const struct dw_i3c_platform_ops ast2600_i3c_ops = {
> +	.init = ast2600_i3c_init,
> +};
> +
> +static int ast2600_i3c_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct of_phandle_args gspec;
> +	struct ast2600_i3c *i3c;
> +	int rc;
> +
> +	i3c = devm_kzalloc(&pdev->dev, sizeof(*i3c), GFP_KERNEL);
> +	if (!i3c)
> +		return -ENOMEM;
> +
> +	rc = of_parse_phandle_with_fixed_args(np, "aspeed,global-regs", 1, 0,
> +					      &gspec);
> +	if (rc)
> +		return -ENODEV;
> +
> +	i3c->global_regs = syscon_node_to_regmap(gspec.np);
> +	of_node_put(gspec.np);
> +
> +	if (IS_ERR(i3c->global_regs))
> +		return PTR_ERR(i3c->global_regs);
> +
> +	i3c->global_idx = gspec.args[0];
> +
> +	rc = of_property_read_u32(np, "sda-pullup-ohms", &i3c->sda_pullup);
> +	if (rc)
> +		i3c->sda_pullup = AST2600_DEFAULT_SDA_PULLUP_OHMS;
> +
> +	rc = ast2600_i3c_pullup_to_reg(i3c->sda_pullup, NULL);
> +	if (rc)
> +		dev_err(&pdev->dev, "invalid sda-pullup value %d\n",
> +			i3c->sda_pullup);
> +
> +	i3c->dw.platform_ops = &ast2600_i3c_ops;
> +	return dw_i3c_common_probe(&i3c->dw, pdev);
> +}
> +
> +static int ast2600_i3c_remove(struct platform_device *pdev)
> +{
> +	struct dw_i3c_master *dw_i3c = platform_get_drvdata(pdev);
> +
> +	return dw_i3c_common_remove(dw_i3c);
> +}
> +
> +static const struct of_device_id ast2600_i3c_master_of_match[] = {
> +	{ .compatible = "aspeed,ast2600-i3c", },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, ast2600_i3c_master_of_match);
> +
> +static struct platform_driver ast2600_i3c_driver = {
> +	.probe = ast2600_i3c_probe,
> +	.remove = ast2600_i3c_remove,
> +	.driver = {
> +		.name = "ast2600-i3c-master",
> +		.of_match_table = ast2600_i3c_master_of_match,
> +	},
> +};
> +module_platform_driver(ast2600_i3c_driver);
> +
> +MODULE_AUTHOR("Jeremy Kerr<jk at codeconstruct.com.au>");
> +MODULE_DESCRIPTION("ASPEED AST2600 I3C driver");
> +MODULE_LICENSE("GPL");
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/linux-aspeed/attachments/20230428/3fee3570/attachment.htm>


More information about the Linux-aspeed mailing list