[PATCH v2 1/3] dt-bindings: mmc: sdhci-of-aspeed: Add description for AST2600 EVB.
Steven Lee
steven_lee at aspeedtech.com
Mon May 3 11:43:34 AEST 2021
Add the description for describing the AST 2600 EVB reference design of
GPIO regulators and provide the example in the document.
AST2600-A2 EVB has the reference design for enabling SD bus
power and toggling SD bus signal voltage by GPIO pins.
In the reference design, GPIOV0 of AST2600-A2 EVB is connected to
power load switch that providing 3.3v to SD1 bus vdd. GPIOV1 is
connected to a 1.8v and a 3.3v power load switch that providing
signal voltage to
SD1 bus.
If GPIOV0 is active high, SD1 bus is enabled. Otherwise, SD1 bus is
disabled.
If GPIOV1 is active high, 3.3v power load switch is enabled, SD1
signal voltage is 3.3v. Otherwise, 1.8v power load switch will be
enabled, SD1 signal voltage becomes 1.8v.
AST2600-A2 EVB also support toggling signal voltage for SD2 bus.
The design is the same as SD1 bus. It uses GPIOV2 as power-gpio and
GPIOV3 as power-switch-gpio.
Signed-off-by: Steven Lee <steven_lee at aspeedtech.com>
---
.../devicetree/bindings/mmc/aspeed,sdhci.yaml | 99 +++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
index 987b287f3bff..dd894aba0bb7 100644
--- a/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
+++ b/Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
@@ -20,6 +20,19 @@ description: |+
the slots are dependent on the common configuration area, they are described
as child nodes.
+ The signal voltage of SDHCIs on AST2600-A2 EVB is able to be toggled by GPIO
+ pins. In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ power load switch that providing 3.3v to SD1 bus vdd, GPIOV1 is connected to
+ a 1.8v and a 3.3v power load switch that providing signal voltage to
+ SD1 bus.
+ If GPIOV0 is active high, SD1 bus is enabled. Otherwise, SD1 bus is
+ disabled. If GPIOV1 is active high, 3.3v power load switch is enabled, SD1
+ signal voltage is 3.3v. Otherwise, 1.8v power load switch will be enabled, SD1
+ signal voltage becomes 1.8v.
+ AST2600-A2 EVB also support toggling signal voltage for SD2 bus.
+ The design is the same as SD1 bus. It uses GPIOV2 as power-gpio and GPIOV3
+ as power-switch-gpio.
+
properties:
compatible:
enum:
@@ -78,6 +91,7 @@ required:
- clocks
examples:
+ //Example 1
- |
#include <dt-bindings/clock/aspeed-clock.h>
sdc at 1e740000 {
@@ -104,3 +118,88 @@ examples:
clocks = <&syscon ASPEED_CLK_SDIO>;
};
};
+
+ //Example 2 (AST2600EVB with GPIO regulator)
+ - |
+ #include <dt-bindings/clock/aspeed-clock.h>
+ #include <dt-bindings/gpio/aspeed-gpio.h>
+ vcc_sdhci0: regulator-vcc-sdhci0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHCI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 0)
+ GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhci0: regulator-vccq-sdhci0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHCI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 1)
+ GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vcc_sdhci1: regulator-vcc-sdhci1 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHCI1 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 2)
+ GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhci1: regulator-vccq-sdhci1 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHCI1 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 ASPEED_GPIO(V, 3)
+ GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ sdc at 1e740000 {
+ compatible = "aspeed,ast2600-sd-controller";
+ reg = <0x1e740000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1e740000 0x20000>;
+ clocks = <&syscon ASPEED_CLK_GATE_SDCLK>;
+
+ sdhci0: sdhci at 100 {
+ compatible = "aspeed,ast2600-sdhci", "sdhci";
+ reg = <0x100 0x100>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ sdhci,auto-cmd12;
+ clocks = <&syscon ASPEED_CLK_SDIO>;
+ vmmc-supply = <&vcc_sdhci0>;
+ vqmmc-supply = <&vccq_sdhci0>;
+ sd-uhs-sdr104;
+ clk-phase-uhs-sdr104 = <180>, <180>;
+ };
+
+ sdhci1: sdhci at 200 {
+ compatible = "aspeed,ast2600-sdhci", "sdhci";
+ reg = <0x200 0x100>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ sdhci,auto-cmd12;
+ clocks = <&syscon ASPEED_CLK_SDIO>;
+ vmmc-supply = <&vcc_sdhci1>;
+ vqmmc-supply = <&vccq_sdhci1>;
+ sd-uhs-sdr104;
+ clk-phase-uhs-sdr104 = <0>, <0>;
+ };
+ };
--
2.17.1
More information about the Linux-aspeed
mailing list