[v2 2/8] dt-bindings: iio: adc: Binding ast2600 adc.
Jonathan Cameron
Jonathan.Cameron at Huawei.com
Sat Jul 24 00:51:41 AEST 2021
On Fri, 23 Jul 2021 16:16:15 +0800
Billy Tsai <billy_tsai at aspeedtech.com> wrote:
> This patch add more description about aspeed adc and add two property
> for ast2600:
> - vref: used to configure reference voltage.
> - battery-sensing: used to enable battery sensing mode for last channel.
>
> Signed-off-by: Billy Tsai <billy_tsai at aspeedtech.com>
Hi Billy,
A few comments inline.
Thanks,
Jonathan
> ---
> .../bindings/iio/adc/aspeed,adc.yaml | 28 +++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/aspeed,adc.yaml b/Documentation/devicetree/bindings/iio/adc/aspeed,adc.yaml
> index 23f3da1ffca3..a562a7fbc30c 100644
> --- a/Documentation/devicetree/bindings/iio/adc/aspeed,adc.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/aspeed,adc.yaml
> @@ -10,14 +10,26 @@ maintainers:
> - Joel Stanley <joel at jms.id.au>
>
> description:
I think you need a | after description if you want the formatting to be
maintained (otherwise it will undo the line breaks).
> - This device is a 10-bit converter for 16 voltage channels. All inputs are
> - single ended.
> + • 10-bits resolution for 16 voltage channels.
> + At ast2400/ast2500 the device has only one engine with 16 voltage channels.
> + At ast2600 the device split into two individual engine and each contains 8 voltage channels.
Please wrap lines at 80 chars unless it badly hurts readability.
engines
> + • Channel scanning can be non-continuous.
> + • Programmable ADC clock frequency.
> + • Programmable upper and lower bound for each channels.
I would use threshold rather than bound. A bound restricts the
value, and I think this is measuring it?
> + • Interrupt when larger or less than bounds for each channels.
> + • Support hysteresis for each channels.
> + • Buildin a compensating method.
Built-in
> + Additional feature at ast2600
of ast2600
> + • Internal or External reference voltage.
> + • Support 2 Internal reference voltage 1.2v or 2.5v.
> + • Integrate dividing circuit for battery sensing.
>
> properties:
> compatible:
> enum:
> - aspeed,ast2400-adc
> - aspeed,ast2500-adc
> + - aspeed,ast2600-adc
>
> reg:
> maxItems: 1
> @@ -33,6 +45,18 @@ properties:
> "#io-channel-cells":
> const: 1
>
> + vref:
> + minItems: 900
> + maxItems: 2700
> + default: 2500
> + description:
> + ADC Reference voltage in millivolts.
I'm not clear from this description. Is this describing an externally
connected voltage reference? If so it needs to be done as a regulator.
If it's a classic high precision reference, the dts can just use
a fixed regulator.
> +
> + battery-sensing:
> + type: boolean
> + description:
> + Inform the driver that last channel will be used to sensor battery.
This isn't (I think?) a standard dt binding, so it needs a manufacturer
prefix.
aspeed,battery-sensing
> +
> required:
> - compatible
> - reg
More information about the Linux-aspeed
mailing list