[PATCH 3/3] ARM: config: multi_v5: Enable ASPEED drivers

Andrew Jeffery andrew at aj.id.au
Tue Jul 24 14:56:41 AEST 2018



On Wed, 18 Jul 2018, at 23:23, Joel Stanley wrote:
> This enables the devices used in the AST2400 family of BMC SoCs:
> 
>  - VUART
>  - SPI NOR
>  - LPC controller
>  - LPC snoop (port 80)
>  - Ethernet
>  - GPIO
>  - ADC
>  - I2C
>  - Random number generator
>  - IPMI KCS
>  - IPMI BT
>  - Fan/Tach
> 
> Signed-off-by: Joel Stanley <joel at jms.id.au>
> ---
>  arch/arm/configs/multi_v5_defconfig | 14 +++++++++++++-
>  1 file changed, 13 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/
> multi_v5_defconfig
> index b647e249908e..318b76fa26d1 100644
> --- a/arch/arm/configs/multi_v5_defconfig
> +++ b/arch/arm/configs/multi_v5_defconfig
> @@ -90,10 +90,14 @@ CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_NAND=y
>  CONFIG_MTD_NAND_ATMEL=y
>  CONFIG_MTD_NAND_ORION=y
> +CONFIG_MTD_SPI_NOR=y
> +CONFIG_SPI_ASPEED_SMC=y
>  CONFIG_MTD_UBI=y
>  CONFIG_BLK_DEV_LOOP=y
>  CONFIG_ATMEL_TCLIB=y
>  CONFIG_ATMEL_SSC=m
> +CONFIG_ASPEED_LPC_CTRL=m
> +CONFIG_ASPEED_LPC_SNOOP=m

Any reason that you switch between module and built-in throughout? It's not clear from the commit message.

>  CONFIG_EEPROM_AT24=y
>  # CONFIG_SCSI_PROC_FS is not set
>  CONFIG_BLK_DEV_SD=y
> @@ -107,6 +111,7 @@ CONFIG_NET_DSA_MV88E6060=y
>  CONFIG_NET_DSA_MV88E6XXX=y
>  CONFIG_MACB=y
>  CONFIG_DM9000=y
> +CONFIG_FTGMAC100=m
>  CONFIG_MV643XX_ETH=y
>  CONFIG_R8169=y
>  CONFIG_DAVICOM_PHY=y
> @@ -128,16 +133,20 @@ CONFIG_SERIAL_8250_NR_UARTS=6
>  CONFIG_SERIAL_8250_RUNTIME_UARTS=6
>  CONFIG_SERIAL_8250_EXTENDED=y
>  CONFIG_SERIAL_8250_MANY_PORTS=y
> +CONFIG_SERIAL_8250_ASPEED_VUART=m
>  CONFIG_SERIAL_OF_PLATFORM=y
>  CONFIG_SERIAL_ATMEL=y
>  CONFIG_SERIAL_ATMEL_CONSOLE=y
>  CONFIG_SERIAL_ATMEL_TTYAT=y
>  CONFIG_SERIAL_IMX=y
>  CONFIG_SERIAL_IMX_CONSOLE=y
> +CONFIG_ASPEED_KCS_IPMI_BMC=m
> +CONFIG_ASPEED_BT_IPMI_BMC=m
>  CONFIG_HW_RANDOM=y
> -CONFIG_I2C=y
> +CONFIG_HW_RANDOM_TIMERIOMEM=m
>  # CONFIG_I2C_COMPAT is not set
>  CONFIG_I2C_CHARDEV=y
> +CONFIG_I2C_ASPEED=m
>  CONFIG_I2C_AT91=y
>  CONFIG_I2C_IMX=y
>  CONFIG_I2C_MV64XXX=y
> @@ -146,10 +155,12 @@ CONFIG_SPI=y
>  CONFIG_SPI_ATMEL=y
>  CONFIG_SPI_IMX=y
>  CONFIG_SPI_ORION=y
> +CONFIG_GPIO_ASPEED=m
>  CONFIG_POWER_RESET=y
>  CONFIG_POWER_RESET_GPIO=y
>  CONFIG_POWER_RESET_QNAP=y
>  CONFIG_SENSORS_ADT7475=y
> +CONFIG_SENSORS_ASPEED=y
>  CONFIG_SENSORS_G762=y
>  CONFIG_SENSORS_LM63=y
>  CONFIG_SENSORS_LM75=y
> @@ -240,6 +251,7 @@ CONFIG_MV_XOR=y
>  CONFIG_STAGING=y
>  CONFIG_FB_XGI=y
>  CONFIG_IIO=m
> +CONFIG_ASPEED_ADC=m
>  CONFIG_AT91_ADC=m
>  CONFIG_PWM=y
>  CONFIG_PWM_ATMEL=m
> -- 
> 2.17.1
> 


More information about the Linux-aspeed mailing list