[PATCH v2 4/6] ARM: davinci: da850: add DT node for eth0.

[Prabhakar Lad]

Sekhar ,

On Sun, Feb 3, 2013 at 5:33 PM, Sekhar Nori <nsekhar at ti.com> wrote:
> On 1/28/2013 7:17 PM, Prabhakar Lad wrote:
>> From: Lad, Prabhakar <prabhakar.lad at ti.com>
>>
>> Add eth0 device tree node information and pinmux for mii to da850 by
>> providing interrupt details and local mac address of eth0.
>>
>> Signed-off-by: Lad, Prabhakar <prabhakar.lad at ti.com>
>> Cc: linux-arm-kernel at lists.infradead.org
>> Cc: linux-kernel at vger.kernel.org
>> Cc: davinci-linux-open-source at linux.davincidsp.com
>> Cc: netdev at vger.kernel.org
>> Cc: devicetree-discuss at lists.ozlabs.org
>> Cc: Sekhar Nori <nsekhar at ti.com>
>> Cc: Heiko Schocher <hs at denx.de>
>> ---
>>  arch/arm/boot/dts/da850-evm.dts |    5 +++++
>>  arch/arm/boot/dts/da850.dtsi    |   35 +++++++++++++++++++++++++++++++++++
>>  2 files changed, 40 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
>> index a319491..19aa2b3 100644
>> --- a/arch/arm/boot/dts/da850-evm.dts
>> +++ b/arch/arm/boot/dts/da850-evm.dts
>> @@ -30,6 +30,11 @@
>>               mdio: davinci_mdio at 1e24000 {
>>                       status = "okay";
>>               };
>> +             eth0: emac at 1e20000 {
>> +                     status = "okay";
>> +                     pinctrl-names = "default";
>> +                     pinctrl-0 = <&mii_pins>;
>> +             };
>>       };
>>       nand_cs3 at 62000000 {
>>               status = "okay";
>> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
>> index ba28f2d..76905f3 100644
>> --- a/arch/arm/boot/dts/da850.dtsi
>> +++ b/arch/arm/boot/dts/da850.dtsi
>> @@ -56,6 +56,26 @@
>>                                       0x30 0x01100000  0x0ff00000
>>                               >;
>>                       };
>> +                     mii_pins: pinmux_mii_pins {
>> +                             pinctrl-single,bits = <
>> +                                     /*
>> +                                      * MII_TXEN, MII_TXCLK, MII_COL
>> +                                      * MII_TXD_3, MII_TXD_2, MII_TXD_1
>> +                                      * MII_TXD_0
>> +                                      */
>> +                                     0x8 0x88888880 0xfffffff0
>> +                                     /*
>> +                                      * MII_RXER, MII_CRS, MII_RXCLK
>> +                                      * MII_RXDV, MII_RXD_3, MII_RXD_2
>> +                                      * MII_RXD_1, MII_RXD_0
>> +                                      */
>> +                                     0xc 0x88888888 0xffffffff
>> +                                     /* MDIO_CLK, MDIO_D */
>
> You call this mii_pins, but include mdio pins in there as well. Can you
> separate them out? Then some board which uses rmii can simply reuse the
> entry.
>
Ok makes sense.

>> +                                     0x10 0x00222288 0x00ffffff
>> +                                     /* GPIO2_6 */
>> +                                     0x18 0x00000080 0x000000f0
>
> This is SoC specific pin list. Such board specific pins should not make
> it here.
>
Ok, so this should be set up using GPIO API's ?

>> +                             >;
>> +                     };
>>               };
>>               serial0: serial at 1c42000 {
>>                       compatible = "ns16550a";
>> @@ -88,6 +108,21 @@
>>                       reg = <0x224000 0x1000>;
>>                       bus_freq = <2200000>;
>>               };
>> +             eth0: emac at 1e20000 {
>> +                     compatible = "ti,davinci-dm6467-emac";
>> +                     reg = <0x220000 0x4000>;
>> +                     ti,davinci-ctrl-reg-offset = <0x3000>;
>> +                     ti,davinci-ctrl-mod-reg-offset = <0x2000>;
>> +                     ti,davinci-ctrl-ram-offset = <0>;
>> +                     ti,davinci-ctrl-ram-size = <0x2000>;
>> +                     local-mac-address = [ 00 00 00 00 00 00 ];
>> +                     interrupts = <33
>> +                                     34
>> +                                     35
>> +                                     36
>> +                                     >;
>> +                     phy-handle = <&mdio>;
>
> I doubt this is required. This property is to pass a handle to the phy,
> not mdio bus.
>
Ok I'll check on this.

Regards,
--Prabhakar


> Thanks,
> Sekhar