[PATCH v2 4/6] ARM: davinci: da850: add DT node for eth0.

[Sekhar Nori]

On 1/28/2013 7:17 PM, Prabhakar Lad wrote:
> From: Lad, Prabhakar <prabhakar.lad at ti.com>
> 
> Add eth0 device tree node information and pinmux for mii to da850 by
> providing interrupt details and local mac address of eth0.
> 
> Signed-off-by: Lad, Prabhakar <prabhakar.lad at ti.com>
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: linux-kernel at vger.kernel.org
> Cc: davinci-linux-open-source at linux.davincidsp.com
> Cc: netdev at vger.kernel.org
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: Sekhar Nori <nsekhar at ti.com>
> Cc: Heiko Schocher <hs at denx.de>
> ---
>  arch/arm/boot/dts/da850-evm.dts |    5 +++++
>  arch/arm/boot/dts/da850.dtsi    |   35 +++++++++++++++++++++++++++++++++++
>  2 files changed, 40 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
> index a319491..19aa2b3 100644
> --- a/arch/arm/boot/dts/da850-evm.dts
> +++ b/arch/arm/boot/dts/da850-evm.dts
> @@ -30,6 +30,11 @@
>  		mdio: davinci_mdio at 1e24000 {
>  			status = "okay";
>  		};
> +		eth0: emac at 1e20000 {
> +			status = "okay";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mii_pins>;
> +		};
>  	};
>  	nand_cs3 at 62000000 {
>  		status = "okay";
> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
> index ba28f2d..76905f3 100644
> --- a/arch/arm/boot/dts/da850.dtsi
> +++ b/arch/arm/boot/dts/da850.dtsi
> @@ -56,6 +56,26 @@
>  					0x30 0x01100000  0x0ff00000
>  				>;
>  			};
> +			mii_pins: pinmux_mii_pins {
> +				pinctrl-single,bits = <
> +					/*
> +					 * MII_TXEN, MII_TXCLK, MII_COL
> +					 * MII_TXD_3, MII_TXD_2, MII_TXD_1
> +					 * MII_TXD_0
> +					 */
> +					0x8 0x88888880 0xfffffff0
> +					/*
> +					 * MII_RXER, MII_CRS, MII_RXCLK
> +					 * MII_RXDV, MII_RXD_3, MII_RXD_2
> +					 * MII_RXD_1, MII_RXD_0
> +					 */
> +					0xc 0x88888888 0xffffffff
> +					/* MDIO_CLK, MDIO_D */

You call this mii_pins, but include mdio pins in there as well. Can you
separate them out? Then some board which uses rmii can simply reuse the
entry.

> +					0x10 0x00222288 0x00ffffff
> +					/* GPIO2_6 */
> +					0x18 0x00000080 0x000000f0

This is SoC specific pin list. Such board specific pins should not make
it here.

> +				>;
> +			};
>  		};
>  		serial0: serial at 1c42000 {
>  			compatible = "ns16550a";
> @@ -88,6 +108,21 @@
>  			reg = <0x224000 0x1000>;
>  			bus_freq = <2200000>;
>  		};
> +		eth0: emac at 1e20000 {
> +			compatible = "ti,davinci-dm6467-emac";
> +			reg = <0x220000 0x4000>;
> +			ti,davinci-ctrl-reg-offset = <0x3000>;
> +			ti,davinci-ctrl-mod-reg-offset = <0x2000>;
> +			ti,davinci-ctrl-ram-offset = <0>;
> +			ti,davinci-ctrl-ram-size = <0x2000>;
> +			local-mac-address = [ 00 00 00 00 00 00 ];
> +			interrupts = <33
> +					34
> +					35
> +					36
> +					>;
> +			phy-handle = <&mdio>;

I doubt this is required. This property is to pass a handle to the phy,
not mdio bus.

Thanks,
Sekhar