[PATCH 2/3] netdev/of/phy: Add MDIO bus multiplexer support.

[Grant Likely]

On Aug 31, 2011 2:01 PM, "David Daney" <david.daney at cavium.com> wrote:
>
> This patch adds a somewhat generic framework for MDIO bus
> multiplexers.  It is modeled on the I2C multiplexer.
>
> The multiplexer is needed if there are multiple PHYs with the same
> address connected to the same MDIO bus adepter, or if there is
> insufficient electrical drive capability for all the connected PHY
> devices.
>
> Conceptually it could look something like this:
>
>                   ------------------
>                   | Control Signal |
>                   --------+---------
>                           |
>  ---------------   --------+------
>  | MDIO MASTER |---| Multiplexer |
>  ---------------   --+-------+----
>                     |       |
>                     C       C
>                     h       h
>                     i       i
>                     l       l
>                     d       d
>                     |       |
>     ---------       A       B   ---------
>     |       |       |       |   |       |
>     | PHY at 1 +-------+       +---+ PHY at 1 |
>     |       |       |       |   |       |
>     ---------       |       |   ---------
>     ---------       |       |   ---------
>     |       |       |       |   |       |
>     | PHY at 2 +-------+       +---+ PHY at 2 |
>     |       |                   |       |
>     ---------                   ---------
>
> This framework configures the bus topology from device tree data.  The
> mechanics of switching the multiplexer is left to device specific
> drivers.
>
> The follow-on patch contains a multiplexer driven by GPIO lines.
>
> Signed-off-by: David Daney <david.daney at cavium.com>
> Cc: Grant Likely <grant.likely at secretlab.ca>
> Cc: "David S. Miller" <davem at davemloft.net>
> ---
>  Documentation/devicetree/bindings/net/mdio-mux.txt |  132 ++++++++++++++
>  drivers/net/phy/Kconfig                            |    8 +
>  drivers/net/phy/Makefile                           |    1 +
>  drivers/net/phy/mdio-mux.c                         |  182
++++++++++++++++++++
>  include/linux/mdio-mux.h                           |   18 ++
>  5 files changed, 341 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/net/mdio-mux.txt
>  create mode 100644 drivers/net/phy/mdio-mux.c
>  create mode 100644 include/linux/mdio-mux.h
>
> diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt
b/Documentation/devicetree/bindings/net/mdio-mux.txt
> new file mode 100644
> index 0000000..a908312
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt
> @@ -0,0 +1,132 @@
> +Common MDIO bus multiplexer/switch properties.
> +
> +An MDIO bus multiplexer/switch will have several child busses that are
> +numbered uniquely in a device dependent manner.  The nodes for an MDIO
> +bus multiplexer/switch will have one child node for each child bus.
> +
> +Required properties:
> +- parent-bus : phandle to the parent MDIO bus.

As discussed, I like mdio-parent-bus.

> +
> +Optional properties:
> +- Other properties specific to the multiplexer/switch hardware.
> +
> +Required properties for child nodes:
> +- #address-cells = <1>;
> +- #size-cells = <0>;
> +- cell-index : The sub-bus number.

Use reg, not cell-index. That is what it is there for. And add the
appropriate #address/size-cells in the parent.

I've not reviewed the implementation, but with the changes. I'm okay with
the binding.

g.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/devicetree-discuss/attachments/20110914/ecde4527/attachment.html>