[PATCH v3] net/smsc911x: add device tree probe support
Dave Martin
dave.martin at linaro.org
Fri Sep 9 18:50:30 EST 2011
On Thu, Sep 08, 2011 at 11:29:20AM -0700, Grant Likely wrote:
> On Thu, Sep 08, 2011 at 03:59:46PM +0100, Dave Martin wrote:
> > Hi Shawn,
> >
> > On Sun, Jul 31, 2011 at 02:26:00AM +0800, Shawn Guo wrote:
> > > It adds device tree probe support for smsc911x driver.
> > >
> > > Signed-off-by: Shawn Guo <shawn.guo at linaro.org>
> > > Cc: Grant Likely <grant.likely at secretlab.ca>
> > > Cc: Steve Glendinning <steve.glendinning at smsc.com>
> > > Cc: David S. Miller <davem at davemloft.net>
> > > Reviewed-by: Grant Likely <grant.likely at secretlab.ca>
> > > ---
> > > Changes since v2:
> > > * Fix a typo in smsc911x.txt
> > >
> > > Changes since v1:
> > > * Instead of getting irq line from gpio number, it use irq domain
> > > to keep platform_get_resource(IORESOURCE_IRQ) works for dt too.
> > > * Use 'lan9115' the first model that smsc911x supports in the match
> > > table
> > > * Use reg-shift and reg-io-width which already used in of_serial for
> > > shift and access size binding
> >
> > When using this patch with vexpress, I found that 16-bit register access
> > mode doesn't seem to be getting set correctly.
> >
> > Can you take a look at this additional patch and let me know if it looks
> > correct?
> >
> > Cheers
> > ---Dave
> >
> > From: Dave Martin <dave.martin at linaro.org>
> > Date: Wed, 7 Sep 2011 17:26:31 +0100
> > Subject: [PATCH] net/smsc911x: Correctly configure 16-bit register access from DT
> >
> > The SMSC911X_USE_16BIT needs to be set when using 16-bit register
> > access. However, currently no flag is set if the DT doesn't specify
> > 32-bit access.
> >
> > This patch should set the SMSC911X_USE_16BIT flag in a manner consistent
> > with the documented DT bindings.
> >
> > Signed-off-by: Dave Martin <dave.martin at linaro.org>
> > ---
> > drivers/net/smsc911x.c | 2 ++
> > 1 files changed, 2 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/net/smsc911x.c b/drivers/net/smsc911x.c
> > index 75c08a5..1a35c25 100644
> > --- a/drivers/net/smsc911x.c
> > +++ b/drivers/net/smsc911x.c
> > @@ -2121,6 +2121,8 @@ static int __devinit smsc911x_probe_config_dt(
> > of_property_read_u32(np, "reg-io-width", &width);
> > if (width == 4)
> > config->flags |= SMSC911X_USE_32BIT;
> > + else
> > + config->flags |= SMSC911X_USE_16BIT;
>
> Would it be better to do "else if (width == 2)"? (completely
> uninformed comment. I've not looked at what the non-DT probe path
> does on this driver.)
I wouldn't have a problem with that. But currently the binding
documentation says that any value other than 4, or a missing property,
implies 16-bit register access.
So the binding documentation would need to change too in that case.
Personally I think this would be better, but it's just an opinion.
Cheers
---Dave
More information about the devicetree-discuss
mailing list