[PATCH V3 4/7] cpufreq: add generic cpufreq driver

Jamie Iles jamie at jamieiles.com
Tue Dec 20 01:39:13 EST 2011


On Mon, Dec 19, 2011 at 10:19:29PM +0800, Richard Zhao wrote:
> On Mon, Dec 19, 2011 at 10:05:12AM +0000, Jamie Iles wrote:
> > Hi Richard,
> > 
> > On Mon, Dec 19, 2011 at 11:21:40AM +0800, Richard Zhao wrote:
> > > It support single core and multi-core ARM SoCs. But currently it assume
> > > all cores share the same frequency and voltage.
> > > 
> > > Signed-off-by: Richard Zhao <richard.zhao at linaro.org>
> > > ---
> > >  .../devicetree/bindings/cpufreq/generic-cpufreq    |    7 +
> > >  drivers/cpufreq/Kconfig                            |    8 +
> > >  drivers/cpufreq/Makefile                           |    2 +
> > >  drivers/cpufreq/generic-cpufreq.c                  |  251 ++++++++++++++++++++
> > >  4 files changed, 268 insertions(+), 0 deletions(-)
> > >  create mode 100644 Documentation/devicetree/bindings/cpufreq/generic-cpufreq
> > >  create mode 100644 drivers/cpufreq/generic-cpufreq.c
> > > 
> > > diff --git a/Documentation/devicetree/bindings/cpufreq/generic-cpufreq b/Documentation/devicetree/bindings/cpufreq/generic-cpufreq
> > > new file mode 100644
> > > index 0000000..15dd780
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/cpufreq/generic-cpufreq
> > > @@ -0,0 +1,7 @@
> > > +Generic cpufreq driver
> > > +
> > > +Required properties in /cpus/cpu at 0:
> > > +- compatible : "generic-cpufreq"
> > 
> > I'm not convinced this is the best way to do this.  By requiring a 
> > generic-cpufreq compatible string we're encoding Linux driver 
> > information into the hardware description.  The only way I can see to 
> > avoid this is to provide a generic_clk_cpufreq_init() function that 
> > platforms can call in their machine init code to use the driver.
> It'll prevent the driver from being a kernel module.

Hmm, that's not very nice either!  I guess you _could_ add an 
of_machine_is_compatible() check against a list of compatible machines 
in the driver but that feels a little gross.  Hopefully Rob or Grant 
have a good alternative!

> Hi Grant & Rob,
> 
> Could you comment?
> 
> > 
> > > +- cpu-freqs : cpu frequency points it support
> > > +- cpu-volts : cpu voltages required by the frequency point at the same index
> > > +- trans-latency :  transition_latency
> > > diff --git a/drivers/cpufreq/Kconfig b/drivers/cpufreq/Kconfig
> > > index e24a2a1..216eecd 100644
> > > --- a/drivers/cpufreq/Kconfig
> > > +++ b/drivers/cpufreq/Kconfig
> > > @@ -179,6 +179,14 @@ config CPU_FREQ_GOV_CONSERVATIVE
> > >  
> > >  	  If in doubt, say N.
> > >  
> > > +config GENERIC_CPUFREQ_DRIVER
> > > +	bool "Generic cpufreq driver using clock/regulator/devicetree"
> > > +	help
> > > +	  This adds generic CPUFreq driver. It assumes all
> > > +	  cores of the CPU share the same clock and voltage.
> > > +
> > > +	  If in doubt, say N.
> > 
> > I think this needs dependencies on HAVE_CLK, OF and REGULATOR.
> right, Thanks. I can not check clk before generic clock framework
> come in.
> Added:
> 	depends on OF && REGULATOR
> 	select CPU_FREQ_TABLE

You can still use HAVE_CLK.  That symbol has been around for ages and 
any platform implementing the clk API should select it so it's fine to 
depend on it even before there is a generic struct clk.

Jamie


More information about the devicetree-discuss mailing list