How to handle named resources with DT?

Cousson, Benoit b-cousson at ti.com
Fri Aug 12 18:56:13 EST 2011


On 8/12/2011 6:10 AM, Shawn Guo wrote:
> On Tue, Aug 09, 2011 at 11:37:10PM +0200, Cousson, Benoit wrote:
>> On 8/9/2011 11:16 PM, Grant Likely wrote:
>>> On Tue, Aug 09, 2011 at 11:06:30PM +0200, Cousson, Benoit wrote:
>>>> On 8/9/2011 10:55 PM, Grant Likely wrote:
>>>>> On Tue, Aug 09, 2011 at 07:47:20PM +0200, Cousson, Benoit wrote:
>>>>>> On 8/9/2011 7:23 PM, Grant Likely wrote:
>>>>>>> On Tue, Aug 9, 2011 at 10:57 AM, Cousson, Benoit<b-cousson at ti.com>     wrote:
>>>>>>>> Hi Manju,
>>>>>>>>
>>>>>>>> On 8/9/2011 6:29 PM, G, Manjunath Kondaiah wrote:
>>>>>>>>>
>>>>>>>>> Hi Benoit,
>>>>>>>>>
>>>>>>>>> On Tue, Aug 09, 2011 at 11:23:20AM +0200, Cousson, Benoit wrote:
>>>>>>>>>>
>>>>>>>>>> Hi Grant,
>>>>>>>>>>
>>>>>>>>>> Trying to bind hwmod informations with DT, I'm facing a little
>>>>>>>>>> limitation.
>>>>>>>>>> A bunch of drivers are using the platform_get_resource_byname, so
>>>>>>>>>> the name for the resource is needed.
>>>>>>>>>>
>>>>>>>>>> The name is used so far for IORESOURCE_MEM, IORESOURCE_IRQ and
>>>>>>>>>> IORESOURCE_DMA types of resources.
>>>>>>>>>
>>>>>>>>> IORESOURCE_MEM and IORESOURCE_IRQ's are fetched from dt blob and
>>>>>>>>> it will be part of pdev.
>>>>>>>>
>>>>>>>> Yes, but without the proper name in the resource structure. It will be then
>>>>>>>> impossible to use the platform_get_resource_byname function that is
>>>>>>>> currently used by a bunch of drivers.
>>>>>>>
>>>>>>> There is no analogous mechanism for _byname in the device tree.  The
>>>>>>> DT binding for a device must explicitly state what order the register
>>>>>>> ranges are in.  The driver will need to be adapted.
>>>>>>
>>>>>> That seems to be a small regression for my point of view. Relying on
>>>>>> the order is not super safe. This is not very readable either.
>>>>>> That's for that exact reason that we changed our drivers to use
>>>>>> platform_get_resource_byname. That's probably the reason why that
>>>>>> API is there as well.
>>>>>> For the same IP, the number of entries can vary depending of the SoC
>>>>>> revision.
>>>>>> By using the _byname, we can check if the resource is there or not
>>>>>> without having to care about the position.
>>>>>
>>>>> We've done it that way for a very long time with the device tree.  If
>>>>> you want to do something by name, then propose a binding that will
>>>>> make it work alongside the existing scheme.
>>>>>
>>>>>>
>>>>>>>>> For IORESOURCE_DMA, you can have property
>>>>>>>>> "dma-channel" in dtsi file and fetch dma-channel in driver probe
>>>>>>>>> through "of_property_read_u32()" api.
>>>>>>>>
>>>>>>>> That will not be enough to get the name. So maybe something like:
>>>>>>>>         dmas =<12>, "rx_req",<13>, "tx_req";
>>>>>>>> will be doable.
>>>>>>>> The issue is that the name is optional so managing the multiple entries
>>>>>>>> might be tricky.
>>>>>>>
>>>>>>> DMA channels will never show up in the resource structure anyway.
>>>>>>
>>>>>> Can you elaborate on that point? AFAIK, IORESOURCE_DMA is already
>>>>>> used today.
>>>>>
>>>>> IORESOURCE_DMA is a Linux construct, as is IORESOURCE_IRQ and
>>>>> IORESOURCE_MEM.  However, IRQ and MEM can be directly mapped from the
>>>>> common 'reg' and 'interrupts' bindings used by pretty much all device
>>>>> tree nodes.  Therefore common code can be written to translate MEM and
>>>>> IRQ that will always work.  There is no such common binding in place
>>>>> for DMA regions, so common setup code cannot do it transparently for
>>>>> the device driver.
>>>>
>>>> OK, sure, I get your point now. I was thinking about a "potential"
>>>> dma support from the core DT, since this is very similar to IRQ.
>>>>
>>>> Otherwise, we can do it OMAP specific if nobody else care about
>>>> that. But I still think it should be useful for other platforms.
>>>
> It is definitely useful for other platforms, so please add the support
> in DT core.

Well, I still have to solve the resource_byname issue for IRQ and REG 
first :-)

>>> I think people care, and it will be a net win, but it does mean you
>>> need do the work of crafting a binding that will work for a large
>>> proportion of SoCs.
>>
> When it comes out, I will happily test it on imx :)

Now, you are putting a lot of pressure on my shoulders :-)

We are still missing basic DT support for OMAP4 and just started the 
OMAP3 beagleboard, so it will take some time before facing the DMA 
issue. But it will happen, probably sooner than later.

>
>> The devil is in the details, but the way the DMA lines are connected
>> in OMAP is similar to IRQ lines, and maybe a little bit simpler.
>>
>> So starting with a copy/paste of the of_irq file should be a good start.
>> And then the issues will start:-)
>>
>
> I had a conversation with Arnd as below.  Arnd has the concern on
> multiple dma controllers.  So it is a question if we need to handle
> multiple dma controllers like we do for multiple irq controllers.

Quite, interesting, I cannot find the thread, did you discuss that on 
linaro-dev, lakml?

> --- quote ---
> Shawn Guo:
>> Then like that IRQ number is decoded and populated into IORESOURCE_IRQ
>> by device tree infrastructural code, we can also do the same into
>> IORESOURCE_DMA.  In that case, drivers do not need any code change for
>> getting dma channel/event numbers from device tree, as
>> platform_get_resource(pdev, IORESOURCE_DMA) still works for them.
>
> Arnd Bergmann:
> But I really don't think there is value in using IORESOURCE_DMA for this.
> We don't have the code to manage DMA resources for more than one DMA
> controller AFAICT, and I think we should not add it. Globally
> unique interrupt numbers cause us a lot of trouble and we go to great
> lengths to fake them on modern devices.

Yeah, that totally makes sense. We do have several DMA engines in OMAP 
anyway, so unique number is clearly not the best approach.
But in that case, it means adding a new kernel API for that and not only 
an of_XXX one. Because driver should then rely on it with or without DT.

> It would be much better
> not to have them visible in the OS, and I don't want to add them to
> a modern API like the dmaengine.

That part is less clear to me, what does it means?

Regards,
Benoit



More information about the devicetree-discuss mailing list