[PATCH v11 3/6] flexcan: Fix up fsl-flexcan device tree binding.

[Grant Likely]

On Thu, Aug 11, 2011 at 10:07 AM, Robin Holt <holt at sgi.com> wrote:
> This patch cleans up the documentation of the device-tree binding for
> the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
> properties are not used by the driver so we are removing them.
>
> Signed-off-by: Robin Holt <holt at sgi.com>
> To: Marc Kleine-Budde <mkl at pengutronix.de>,
> To: Wolfgang Grandegger <wg at grandegger.com>,
> To: U Bhaskar-B22300 <B22300 at freescale.com>
> To: Scott Wood <scottwood at freescale.com>
> To: Grant Likely <grant.likely at secretlab.ca>
> To: Kumar Gala <galak at kernel.crashing.org>
> Cc: socketcan-core at lists.berlios.de,
> Cc: netdev at vger.kernel.org,
> Cc: PPC list <linuxppc-dev at lists.ozlabs.org>
> Cc: devicetree-discuss at lists.ozlabs.org
> ---
>  .../devicetree/bindings/net/can/fsl-flexcan.txt    |   69 ++++---------------
>  arch/powerpc/boot/dts/p1010rdb.dts                 |   10 +--
>  arch/powerpc/boot/dts/p1010si.dtsi                 |   10 +--
>  3 files changed, 21 insertions(+), 68 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> index 1a729f0..c78dcbb 100644
> --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
> @@ -1,61 +1,22 @@
> -CAN Device Tree Bindings
> -------------------------
> -2011 Freescale Semiconductor, Inc.
> +Flexcan CAN contoller on Freescale's ARM and PowerPC processors
>
> -fsl,flexcan-v1.0 nodes
> ------------------------
> -In addition to the required compatible-, reg- and interrupt-properties, you can
> -also specify which clock source shall be used for the controller.
> +Required properties:
>
> -CPI Clock- Can Protocol Interface Clock
> -       This CLK_SRC bit of CTRL(control register) selects the clock source to
> -       the CAN Protocol Interface(CPI) to be either the peripheral clock
> -       (driven by the PLL) or the crystal oscillator clock. The selected clock
> -       is the one fed to the prescaler to generate the Serial Clock (Sclock).
> -       The PRESDIV field of CTRL(control register) controls a prescaler that
> -       generates the Serial Clock (Sclock), whose period defines the
> -       time quantum used to compose the CAN waveform.
> +- compatible : Should be "fsl,<processor>-flexcan" and "fsl,flexcan"

Don't do this.  "fsl,flexcan" is far too generic.  Be specific to the
soc part number or the ip core implementation version.

>
> -Can Engine Clock Source
> -       There are two sources for CAN clock
> -       - Platform Clock  It represents the bus clock
> -       - Oscillator Clock
> +  An implementation should also claim any of the following compatibles
> +  that it is fully backwards compatible with:
>
> -       Peripheral Clock (PLL)
> -       --------------
> -                    |
> -                   ---------                 -------------
> -                   |       |CPI Clock        | Prescaler |       Sclock
> -                   |       |---------------->| (1.. 256) |------------>
> -                   ---------                 -------------
> -                     |  |
> -       --------------  ---------------------CLK_SRC
> -       Oscillator Clock
> +  - fsl,p1010-flexcan
>
> -- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects
> -                            the peripheral clock. PLL clock is fed to the
> -                            prescaler to generate the Serial Clock (Sclock).
> -                            Valid values are "oscillator" and "platform"
> -                            "oscillator": CAN engine clock source is oscillator clock.
> -                            "platform" The CAN engine clock source is the bus clock
> -                            (platform clock).
> +- reg : Offset and length of the register set for this device
> +- interrupts : Interrupt tuple for this device
>
> -- fsl,flexcan-clock-divider : for the reference and system clock, an additional
> -                             clock divider can be specified.
> -- clock-frequency: frequency required to calculate the bitrate for FlexCAN.
> +Example:
>
> -Note:
> -       - v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC.
> -       - P1010 does not have oscillator as the Clock Source.So the default
> -         Clock Source is platform clock.
> -Examples:
> -
> -       can0 at 1c000 {
> -               compatible = "fsl,flexcan-v1.0";
> -               reg = <0x1c000 0x1000>;
> -               interrupts = <48 0x2>;
> -               interrupt-parent = <&mpic>;
> -               fsl,flexcan-clock-source = "platform";
> -               fsl,flexcan-clock-divider = <2>;
> -               clock-frequency = <fixed by u-boot>;
> -       };
> +  can at 1c000 {
> +          compatible = "fsl,p1010-flexcan", "fsl,flexcan";
> +          reg = <0x1c000 0x1000>;
> +          interrupts = <48 0x2>;
> +          interrupt-parent = <&mpic>;
> +  };

The diffstat for this patch looks too big because the whitespace has
changed.  Try to restrict whitespace changes so that the patch is
friendly to reviewers.

g.