PCIe bus seems work while 'dma' can't under linux

jxnuxdy jxnuxdy at 163.com
Fri Jun 11 11:30:19 EST 2010


Hi guys,

I encountered a PCIe problem under linux, the two PCIe bus on my board seems work, at least I can access the registers through the PCIe bus, however the dma for the PCIe bus can't work, so I just dumped the pci device, but I am curiously to find there is no regions displayed on PCIe controlers, why? is it relate with my 'dma' issue then?


bash-2.04# cat /proc/pci
PCI devices found:
  Bus  0, device   0, function  0:
    Class 0b20  Header Type 01: PCI device 1957:0032 (rev 17).
  Bus  1, device   0, function  0:
    Class 0580  Header Type 00: PCI device 11ab:db90 (rev 1).
      Prefetchable 64 bit memory at 0x80000000 [0x800fffff].
      Prefetchable 64 bit memory at 0x84000000 [0x87ffffff].
  Bus  9, device   0, function  0:
    Class 0b20  Header Type 01: PCI device 1957:0032 (rev 17).
  Bus 10, device   0, function  0:
    Class 0580  Header Type 00: PCI device 11ab:db90 (rev 1).
      Prefetchable 64 bit memory at 0xa0000000 [0xa00fffff].
      Prefetchable 64 bit memory at 0xa4000000 [0xa7ffffff].
bash-2.04# lspci -vv
00:00.0 Power PC: Unknown device 1957:0032 (rev 11)
        !!! Invalid class 0b20 for header type 01
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, cache line size 08
        Bus: primary=00, secondary=01, subordinate=06, sec-latency=0
        I/O behind bridge: 00000000-00000fff
        Memory behind bridge: 80000000-9fffffff
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [4c] #10 [0041]

01:00.0 Memory controller: Galileo Technology Ltd.: Unknown device db90 (rev 01)
        Subsystem: Galileo Technology Ltd.: Unknown device 11ab
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, cache line size 08
        Interrupt: pin A routed to IRQ 0
        Region 0: Memory at 80000000 (64-bit, prefetchable) [size=1M]
        Region 2: Memory at 84000000 (64-bit, prefetchable) [size=64M]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [60] #10 [0011]

09:00.0 Power PC: Unknown device 1957:0032 (rev 11)
        !!! Invalid class 0b20 for header type 01
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, cache line size 08
        Bus: primary=00, secondary=0a, subordinate=0f, sec-latency=0
        I/O behind bridge: 00000000-00000fff
        Memory behind bridge: a0000000-bfffffff
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [4c] #10 [0041]

0a:00.0 Memory controller: Galileo Technology Ltd.: Unknown device db90 (rev 01)
        Subsystem: Galileo Technology Ltd.: Unknown device 11ab
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, cache line size 08
        Interrupt: pin A routed to IRQ 0
        Region 0: Memory at a0000000 (64-bit, prefetchable) [size=1M]
        Region 2: Memory at a4000000 (64-bit, prefetchable) [size=64M]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [60] #10 [0011]

bash-2.04# 

Thanks
Denny



More information about the devicetree-discuss mailing list