[Skiboot] [PATCH 02/19] hw/ast-bmc: Initialize ast lpc mctp binding
Christophe Lombard
clombard at linux.vnet.ibm.com
Sat Feb 26 01:28:31 AEDT 2022
The Management Component Transport Protocol (MCTP) defines a communication
model intended to facilitate communication.
This patch initialize MCTP binding over LPC Bus interface.
Several steps must be performed:
- Initialize the MCTP core (mctp_init()).
- Initialize a hardware binding as AST LPC mode host (mctp_astlpc_init()).
- Register the hardware binding with the core (mctp_register_bus()), using
a predefined EID (Host default is 9).
To transmit a MCTP message, mctp_message_tx() is used.
To receive a MCTP message, a callback need to be provided and registered
through mctp_set_rx_all().
For the transfer of MCTP messages, two basics components are used:
- A window of the LPC FW address space, where reads and writes are
forwarded to BMC memory.
- An interrupt mechanism using the KCS interface.
hw/ast-bmc/ast-mctp.c is compilated if the compiler flag CONFIG_PLDM is
set.
Signed-off-by: Christophe Lombard <clombard at linux.vnet.ibm.com>
---
hw/ast-bmc/Makefile.inc | 6 +
hw/ast-bmc/ast-mctp.c | 344 ++++++++++++++++++++++++++++++++++++++++
include/ast.h | 6 +
3 files changed, 356 insertions(+)
create mode 100644 hw/ast-bmc/ast-mctp.c
diff --git a/hw/ast-bmc/Makefile.inc b/hw/ast-bmc/Makefile.inc
index e7ded0e8..8a546f97 100644
--- a/hw/ast-bmc/Makefile.inc
+++ b/hw/ast-bmc/Makefile.inc
@@ -2,5 +2,11 @@
SUBDIRS += hw/ast-bmc
AST_BMC_OBJS = ast-io.o ast-sf-ctrl.o
+
+ifeq ($(CONFIG_PLDM),1)
+CPPFLAGS += -I$(SRC)/libmctp/
+AST_BMC_OBJS += ast-mctp.o
+endif
+
AST_BMC = hw/ast-bmc/built-in.a
$(AST_BMC): $(AST_BMC_OBJS:%=hw/ast-bmc/%)
diff --git a/hw/ast-bmc/ast-mctp.c b/hw/ast-bmc/ast-mctp.c
new file mode 100644
index 00000000..1c759a94
--- /dev/null
+++ b/hw/ast-bmc/ast-mctp.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: Apache-2.0 OR GPL-2.0-or-later
+// Copyright 2022 IBM Corp.
+
+#define pr_fmt(fmt) "AST-MCTP: " fmt
+
+#include <lpc.h>
+#include <interrupts.h>
+#include <timer.h>
+#include <timebase.h>
+#include <debug_descriptor.h>
+#include <ast.h>
+#include <console.h>
+#include <libmctp.h>
+#include <libmctp-cmds.h>
+#include <libmctp-log.h>
+#include <libmctp-astlpc.h>
+
+/*
+ * For the EIDs: the valid range is 8-254.
+ * host default = 9
+ */
+uint8_t HOST_EID = 9;
+
+static struct mctp *mctp;
+
+/* binding specific */
+struct astlpc_ops_data {
+
+ uint16_t kcs_data_addr; /* LPC IO space offset for the data register */
+ uint16_t kcs_stat_addr;
+
+ /* address of the packet exchange buffer in FW space */
+ uint32_t lpc_fw_addr;
+};
+
+/*
+ * The AST binding is described here:
+ *
+ * https://github.com/openbmc/libmctp/blob/master/docs/bindings/vendor-astlpc.md
+ *
+ * Most of the binding is implemented in libmctp, but we need to provide
+ * accessors for the LPC FW space (for the packet buffer) and for the KCS
+ * peripheral (for the interrupt mechanism).
+ */
+
+static int ast_kcs_reg_read(void *binding_data,
+ enum mctp_binding_astlpc_kcs_reg reg,
+ uint8_t *val)
+{
+ struct astlpc_ops_data *ops_data = binding_data;
+ uint32_t addr, tmp;
+ int rc;
+
+ if (reg == MCTP_ASTLPC_KCS_REG_STATUS)
+ addr = ops_data->kcs_stat_addr;
+ else if (reg == MCTP_ASTLPC_KCS_REG_DATA)
+ addr = ops_data->kcs_data_addr;
+ else
+ return OPAL_PARAMETER;
+
+ rc = lpc_read(OPAL_LPC_IO, addr, &tmp, 1);
+ if (!rc)
+ *val = tmp & 0xff;
+ else
+ *val = 0xff;
+
+ mctp_prdebug("%s 0x%hhx from %s (%d)",
+ __func__, *val, reg ? "status" : "data", rc);
+
+ return rc;
+}
+
+static int ast_kcs_reg_write(void *binding_data,
+ enum mctp_binding_astlpc_kcs_reg reg,
+ uint8_t val)
+{
+ struct astlpc_ops_data *ops_data = binding_data;
+ uint32_t addr;
+
+ mctp_prdebug("%s 0x%hhx to %s",
+ __func__, val, reg ? "status" : "data");
+
+ if (reg == MCTP_ASTLPC_KCS_REG_STATUS)
+ addr = ops_data->kcs_stat_addr;
+ else if (reg == MCTP_ASTLPC_KCS_REG_DATA)
+ addr = ops_data->kcs_data_addr;
+ else
+ return OPAL_PARAMETER;
+
+ return lpc_write(OPAL_LPC_IO, addr, val, 1);
+}
+
+static int ast_lpc_read(void *binding_data, void *buf, long offset,
+ size_t len)
+{
+ struct astlpc_ops_data *ops_data = binding_data;
+
+ mctp_prdebug("%s %zu bytes from 0x%lx (lpc: 0x%lx)",
+ __func__, len, offset,
+ ops_data->lpc_fw_addr + offset);
+ return lpc_fw_read(ops_data->lpc_fw_addr + offset, buf, len);
+}
+
+static int ast_lpc_write(void *binding_data, const void *buf,
+ long offset, size_t len)
+{
+ struct astlpc_ops_data *ops_data = binding_data;
+
+ mctp_prdebug("%s %zu bytes to offset 0x%lx (lpc: 0x%lx)",
+ __func__, len, offset,
+ ops_data->lpc_fw_addr + offset);
+ return lpc_fw_write(ops_data->lpc_fw_addr + offset, buf, len);
+}
+
+static const struct mctp_binding_astlpc_ops astlpc_ops = {
+ .kcs_read = ast_kcs_reg_read,
+ .kcs_write = ast_kcs_reg_write,
+ .lpc_read = ast_lpc_read,
+ .lpc_write = ast_lpc_write,
+};
+
+static struct mctp_binding_astlpc *ast_binding;
+static struct astlpc_ops_data *ops_data;
+
+/* Keyboard Controller Style (KCS) data register address */
+#define KCS_DATA_REG 0xca2
+
+/* Keyboard Controller Style (KCS) status register address */
+#define KCS_STATUS_REG 0xca3
+
+/* Serial IRQ number for KCS interface */
+#define KCS_SERIAL_IRQ 11
+
+bool irq_active;
+struct timer mctp_boot_timer;
+
+/* we need a poller to crank the mctp state machine during boot */
+static void ast_mctp_poller(struct timer *t __unused,
+ void *data __unused, uint64_t now __unused)
+{
+ mctp_astlpc_poll(ast_binding);
+
+ /* once booted we can rely on the KCS interrupt */
+ if ((opal_booting() && !irq_active))
+ schedule_timer(&mctp_boot_timer, msecs_to_tb(5));
+}
+
+/* at runtime the interrupt should handle it */
+static void ast_mctp_interrupt(uint32_t chip_id __unused,
+ uint32_t irq_msk __unused)
+{
+ if (!irq_active) {
+ mctp_prerr("IRQ Active! Disabling boot poller...");
+ irq_active = true;
+ }
+
+ mctp_astlpc_poll(ast_binding);
+}
+
+static struct lpc_client kcs_lpc_client = {
+ .reset = NULL,
+ .interrupt = ast_mctp_interrupt,
+ .interrupts = LPC_IRQ(KCS_SERIAL_IRQ),
+};
+
+static bool ast_mctp_supported(void)
+{
+ uint32_t tmp;
+
+ /*
+ * Probe for MCTP support by reading the STAT register of KCS#4
+ */
+ tmp = 0;
+ return true;
+
+ if (lpc_probe_read(OPAL_LPC_IO, KCS_STATUS_REG, &tmp, 1)) {
+ mctp_prdebug("KCS4 probe failed, skipping MCTP init");
+ return false;
+ }
+
+ return !!(tmp & 0x80); /* high bit indicates BMC is listening */
+}
+
+#define DESIRED_MTU 32768
+
+static struct mctp_binding_astlpc *ast_mctp_binding(void)
+{
+ struct mctp_binding_astlpc *ast_binding;
+
+ ops_data = zalloc(sizeof(struct astlpc_ops_data));
+ if (!ops_data)
+ return NULL;
+
+ /*
+ * Current OpenBMC systems put the MCTP buffer 1MB down from
+ * the end of the LPC FW range.
+ *
+ * The size of the FW range is: 0x1000_0000 so the window be at:
+ *
+ * 0x1000_0000 - 2**20 == 0xff00000
+ */
+ ops_data->lpc_fw_addr = 0xff00000;
+
+ /* values chosen by the OpenBMC driver */
+ ops_data->kcs_data_addr = KCS_DATA_REG;
+ ops_data->kcs_stat_addr = KCS_STATUS_REG;
+
+ /* Initialise the binding */
+ ast_binding = mctp_astlpc_init(MCTP_BINDING_ASTLPC_MODE_HOST,
+ DESIRED_MTU,
+ NULL,
+ &astlpc_ops,
+ ops_data);
+ if (!ast_binding) {
+ mctp_prerr("binding init failed");
+ goto err;
+ }
+
+ /* register an lpc client so we get an interrupt */
+ lpc_register_client(0, &kcs_lpc_client, IRQ_ATTR_TARGET_OPAL);
+
+ init_timer(&mctp_boot_timer, ast_mctp_poller, ast_binding);
+ schedule_timer(&mctp_boot_timer, msecs_to_tb(5));
+
+ return ast_binding;
+
+err:
+ mctp_astlpc_destroy(ast_binding);
+ free(ops_data);
+ return NULL;
+}
+
+static void *mctp_malloc(size_t size) { return malloc(size); }
+static void mctp_free(void *ptr) { return free(ptr); }
+static void *mctp_realloc(void *ptr, size_t size)
+{
+ return realloc(ptr, size);
+}
+
+#ifdef ASTLPC_DEBUG
+char buffer[320];
+static void mctp_log(int log_lvl, const char *fmt, va_list va)
+{
+ snprintf(buffer, sizeof(buffer), "%s\n", fmt);
+ vprlog(log_lvl, buffer, va);
+}
+#endif
+
+int ast_mctp_message_tx(uint8_t eid, uint8_t *msg, int len)
+{
+ return mctp_message_tx(mctp, eid, msg, len);
+}
+
+void ast_mctp_stop_polling(void)
+{
+ irq_active = true;
+}
+
+#define HOST_MAX_INCOMING_MESSAGE_ALLOCATION 131072
+
+/*
+ * Initialize mctp binding for hbrt and provide interfaces for sending
+ * and receiving mctp messages.
+ */
+int ast_mctp_init(void (*fn)(uint8_t src_eid, void *data,
+ void *msg, size_t len))
+{
+ uint64_t start;
+
+ if (!ast_mctp_supported())
+ return OPAL_HARDWARE;
+
+ /* skiboot's malloc/free/realloc are macros so they need
+ * wrappers
+ */
+ mctp_set_alloc_ops(mctp_malloc, mctp_free, mctp_realloc);
+
+ /*
+ * /-----\ /---------\
+ * | bmc | (eid: 8) <- lpc/kcs -> (eid: 9) | skiboot |
+ * \-----/ \---------/
+ * astlpc kcs binding
+ */
+ mctp = mctp_init();
+ if (!mctp) {
+ mctp_prerr("mctp init failed");
+ return OPAL_HARDWARE;
+ }
+
+#ifdef ASTLPC_DEBUG
+ /* Setup the trace hook */
+ mctp_set_log_custom(mctp_log);
+#endif
+
+ mctp_prinfo("libmctp initialized");
+
+ /* Set the max message size to be large enough */
+ mctp_set_max_message_size(mctp, HOST_MAX_INCOMING_MESSAGE_ALLOCATION);
+
+ /* Setup the message rx callback */
+ mctp_set_rx_all(mctp, fn, NULL);
+
+ /* Initialise the binding */
+ ast_binding = ast_mctp_binding();
+ if (!ast_binding)
+ goto err;
+
+ /* Register the binding to the LPC bus we are using for this
+ * MCTP configuration.
+ */
+ if (mctp_register_bus(mctp,
+ mctp_binding_astlpc_core(ast_binding),
+ HOST_EID)) {
+ mctp_prerr("failed to register bus");
+ goto err;
+ }
+
+ /* Initializing the channel requires running the poll function
+ * a few times to handle the initial setup since we need the
+ * BMC to reply.
+ *
+ * Unfortuntately there's no good way to determine if this
+ * worked or not so poll for a bit with a timeout. :(
+ *
+ * We have to check (bus->state == mctp_bus_state_constructed)
+ * otherwise mctp_message_tx() will reject the message.
+ * astlpc: host: Version negotiation got: 3
+ */
+ start = mftb();
+ while (tb_compare(mftb(), start + msecs_to_tb(250)) == TB_ABEFOREB)
+ time_wait_ms(10);
+
+ mctp_prwarn("%s - The mctp bus state should be correct now !!!",
+ __func__);
+
+ return OPAL_SUCCESS;
+
+err:
+ mctp_prerr("Unable to initialize MCTP");
+ mctp_destroy(mctp);
+ mctp = NULL;
+
+ return OPAL_HARDWARE;
+}
diff --git a/include/ast.h b/include/ast.h
index 5e932398..05914444 100644
--- a/include/ast.h
+++ b/include/ast.h
@@ -91,6 +91,12 @@ void ast_setup_ibt(uint16_t io_base, uint8_t irq);
/* MBOX configuration */
void ast_setup_sio_mbox(uint16_t io_base, uint8_t irq);
+/* AST MCTP configuration */
+int ast_mctp_init(void (*fn)(uint8_t src_eid, void *data,
+ void *msg, size_t len));
+void ast_mctp_stop_polling(void);
+int ast_mctp_message_tx(uint8_t eid, uint8_t *msg, int len);
+
#endif /* __SKIBOOT__ */
/*
--
2.35.1
More information about the Skiboot
mailing list