[Skiboot] [PATCH 054/110] doc: flesh out and prettify OPAL_LPC_(READ|WRITE)

Stewart Smith stewart at linux.ibm.com
Fri May 31 16:12:55 AEST 2019


Signed-off-by: Stewart Smith <stewart at linux.ibm.com>
---
 doc/opal-api/opal-lpc-read-write-67-68.rst | 92 +++++++++++++++-------
 1 file changed, 62 insertions(+), 30 deletions(-)

diff --git a/doc/opal-api/opal-lpc-read-write-67-68.rst b/doc/opal-api/opal-lpc-read-write-67-68.rst
index 784147459e08..52d377892330 100644
--- a/doc/opal-api/opal-lpc-read-write-67-68.rst
+++ b/doc/opal-api/opal-lpc-read-write-67-68.rst
@@ -1,11 +1,30 @@
+.. _OPAL_LPC_READ:
+
 OPAL_LPC_READ
 =============
-::
 
-  This function related to Low Pin Count (LPC) bus. This function reads the
-  data from IDSEL register for ``chip_id``, which has LPC information.
-  From ``addr`` for ``addr_type`` with read size ``sz`` bytes in to a
-  variable named ``data``.
+.. code-block:: c
+
+   #define OPAL_LPC_READ				67
+
+   /*
+    * Address cycle types for LPC accesses. These also correspond
+    * to the content of the first cell of the "reg" property for
+    * device nodes on the LPC bus
+    */
+    enum OpalLPCAddressType {
+      OPAL_LPC_MEM	= 0,
+      OPAL_LPC_IO	= 1,
+      OPAL_LPC_FW	= 2,
+   };
+
+   int64_t opal_lpc_read(uint32_t chip_id, enum OpalLPCAddressType addr_type,
+			     uint32_t addr, uint32_t *data, uint32_t sz);
+
+This function related to Low Pin Count (LPC) bus. This function reads the
+data from IDSEL register for ``chip_id``, which has LPC information.
+From ``addr`` for ``addr_type`` with read size ``sz`` bytes in to a
+variable named ``data``.
 
 Parameters
 ----------
@@ -13,40 +32,56 @@ Parameters
 ``chip_id``
   The ``chip_id`` parameter contains value of the chip number identified at
   boot time.
-
 ``addr_type``
   The ``addr_type`` is one of the LPC supported address types.
-  Supported address types are -
-  LPC memory,
-  LPC IO and
-  LPC firmware.
+  Supported address types are:
+
+  - LPC memory,
+  - LPC IO and
+  - LPC firmware.
 
 ``addr``
   The ``addr`` from which the data has to be read.
-
 ``data``
   The ``data`` will be used to store the read data.
-
 ``sz``
    How many ``sz`` bytes to be read in to ``data``.
 
 Return Codes
 ------------
 
-``OPAL_PARAMETER``
+:ref:`OPAL_PARAMETER`
    Indicates either ``chip_id`` not found or ``chip_id`` doesn’t contain
    LPC information.
-
-``OPAL_SUCCESS``
+:ref:`OPAL_SUCCESS`
   Indicates Success!
 
+.. _OPAL_LPC_WRITE:
+
 OPAL_LPC_WRITE
 ==============
-::
 
-  This function related to Low Pin Count (LPC) bus. This function writes the
-  ``data`` in to  ECCB register for ``chip_id``, which has LPC information.
-  From ``addr`` for ``addr_type`` with write size ``sz`` bytes.
+.. code-block:: c
+
+   #define OPAL_LPC_WRITE				68
+
+   /*
+    * Address cycle types for LPC accesses. These also correspond
+    * to the content of the first cell of the "reg" property for
+    * device nodes on the LPC bus
+    */
+    enum OpalLPCAddressType {
+      OPAL_LPC_MEM	= 0,
+      OPAL_LPC_IO	= 1,
+      OPAL_LPC_FW	= 2,
+   };
+
+   int64_t opal_lpc_write(uint32_t chip_id, enum OpalLPCAddressType addr_type,
+                          uint32_t addr, uint32_t data, uint32_t sz);
+
+This function related to Low Pin Count (LPC) bus. This function writes the
+``data`` in to  ECCB register for ``chip_id``, which has LPC information.
+From ``addr`` for ``addr_type`` with write size ``sz`` bytes.
 
 Parameters
 ----------
@@ -54,29 +89,26 @@ Parameters
 ``chip_id``
   The ``chip_id`` parameter contains value of the chip number identified at
   boot time.
-
 ``addr_type``
   The ``addr_type`` is one of the address types LPC supported.
-  Supported address types are -
-  LPC memory,
-  LPC IO and
-  LPC firmware.
+  Supported address types are:
+
+  - LPC memory,
+  - LPC IO and
+  - LPC firmware.
 
 ``addr``
   The ``addr`` to where the ``data`` need to be written.
-
 ``data``
   The ``data`` for writing.
-
 ``sz``
    How many ``sz`` bytes to write.
 
 Return Codes
 ------------
 
-``OPAL_PARAMETER``
+:ref:`OPAL_PARAMETER`
    Indicates either ``chip_id`` not found or ``chip_id`` doesn’t contain LPC
    information.
-
-``OPAL_SUCCESS``
-  Indicates Success!
+:ref:`OPAL_SUCCESS`
+   Indicates Success!
-- 
2.21.0



More information about the Skiboot mailing list