[Skiboot] [PATCH v3 3/7] hw/npu2: Use NVLink irq setup for OpenCAPI
Frederic Barrat
fbarrat at linux.ibm.com
Sat Apr 6 01:33:00 AEDT 2019
Start using the irq setup code from NVLink for OpenCAPI, since the 2
versions are so close. There are only 2 differences:
- the NPU may trigger more interrupts for OpenCAPI, 35 vs. 23, though
none are configured to be triggered for now.
- we need to enable the 4 translation faults interrupts for OpenCAPI.
Signed-off-by: Frederic Barrat <fbarrat at linux.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan at au1.ibm.com>
---
Changelog
v2, v3: no change
hw/npu2-common.c | 19 ++++++++++++++----
hw/npu2-opencapi.c | 50 ++++------------------------------------------
include/npu2.h | 1 -
3 files changed, 19 insertions(+), 51 deletions(-)
diff --git a/hw/npu2-common.c b/hw/npu2-common.c
index b0d55f5d..0b46f68c 100644
--- a/hw/npu2-common.c
+++ b/hw/npu2-common.c
@@ -26,7 +26,7 @@
#include <xive.h>
#define NPU2_IRQ_BASE_SHIFT 13
-#define NPU2_N_DL_IRQS 23
+#define NPU2_N_DL_IRQS 35
#define NPU2_N_DL_IRQS_ALIGN 64
/*
@@ -145,6 +145,18 @@ static char *npu2_ipi_name(struct irq_source *is, uint32_t isn)
case 20: name = "CQ Event"; break;
case 21: name = "MISC Event"; break;
case 22: name = "NMMU Local Xstop"; break;
+ case 23: name = "Translate Fail (brick 2)"; break;
+ case 24: name = "Translate Fail (brick 3)"; break;
+ case 25: name = "Translate Fail (brick 4)"; break;
+ case 26: name = "Translate Fail (brick 5)"; break;
+ case 27: name = "OTL Event (brick 2)"; break;
+ case 28: name = "OTL Event (brick 3)"; break;
+ case 29: name = "OTL Event (brick 4)"; break;
+ case 30: name = "OTL Event (brick 5)"; break;
+ case 31: name = "XSL Event (brick 2)"; break;
+ case 32: name = "XSL Event (brick 3)"; break;
+ case 33: name = "XSL Event (brick 4)"; break;
+ case 34: name = "XSL Event (brick 5)"; break;
default: name = "Unknown";
}
return strdup(name);
@@ -177,7 +189,7 @@ static void setup_irqs(struct npu2 *p)
p->base_lsi = xive_alloc_ipi_irqs(p->chip_id, NPU2_N_DL_IRQS, NPU2_N_DL_IRQS_ALIGN);
if (p->base_lsi == XIVE_IRQ_ERROR) {
- prlog(PR_ERR, "NPU: Failed to allocate interrupt sources, IRQs for NDL No-stall events will not be available.\n");
+ prlog(PR_ERR, "NPU: Failed to allocate interrupt sources\n");
return;
}
xive_register_ipi_source(p->base_lsi, NPU2_N_DL_IRQS, p, &npu2_ipi_ops);
@@ -375,8 +387,7 @@ static void setup_devices(struct npu2 *npu)
return;
}
- if (nvlink_detected)
- setup_irqs(npu);
+ setup_irqs(npu);
if (nvlink_detected)
npu2_nvlink_init_npu(npu);
diff --git a/hw/npu2-opencapi.c b/hw/npu2-opencapi.c
index 905314cc..d32aaa53 100644
--- a/hw/npu2-opencapi.c
+++ b/hw/npu2-opencapi.c
@@ -48,11 +48,9 @@
#include <npu2.h>
#include <npu2-regs.h>
#include <phys-map.h>
-#include <xive.h>
#include <i2c.h>
#include <nvram.h>
-#define NPU_IRQ_LEVELS 35
#define NPU_IRQ_LEVELS_XSL 23
#define MAX_PE_HANDLE ((1 << 15) - 1)
#define TL_MAX_TEMPLATE 63
@@ -1464,7 +1462,7 @@ static int npu2_add_mmio_regs(struct phb *phb, struct pci_device *pd,
* Pass the hw irq number for the translation fault irq
* irq levels 23 -> 26 are for translation faults, 1 per brick
*/
- irq = dev->npu->irq_base + NPU_IRQ_LEVELS_XSL;
+ irq = dev->npu->base_lsi + NPU_IRQ_LEVELS_XSL;
if (stacku == NPU2_STACK_STCK_2U)
irq += 2;
if (block == NPU2_BLOCK_OTL1)
@@ -1537,43 +1535,9 @@ static void mask_nvlink_fir(struct npu2 *p)
NPU2_MISC_IRQ_ENABLE1, NPU2_MISC_DA_LEN_8B, reg);
}
-static int setup_irq(struct npu2 *p)
+static int enable_xsl_irq(struct npu2 *p)
{
- uint64_t reg, mmio_addr;
- uint32_t base;
-
- base = xive_alloc_ipi_irqs(p->chip_id, NPU_IRQ_LEVELS, 64);
- if (base == XIVE_IRQ_ERROR) {
- /**
- * @fwts-label OCAPIIRQAllocationFailed
- * @fwts-advice OpenCAPI IRQ setup failed. This is probably
- * a firmware bug. OpenCAPI functionality will be broken.
- */
- prlog(PR_ERR, "OCAPI: Couldn't allocate interrupts for NPU\n");
- return -1;
- }
- p->irq_base = base;
-
- xive_register_ipi_source(base, NPU_IRQ_LEVELS, NULL, NULL);
- mmio_addr = (uint64_t ) xive_get_trigger_port(base);
- prlog(PR_DEBUG, "OCAPI: NPU base irq %d @%llx\n", base, mmio_addr);
- reg = (mmio_addr & NPU2_MISC_IRQ_BASE_MASK) << 13;
- npu2_scom_write(p->chip_id, p->xscom_base, NPU2_MISC_IRQ_BASE,
- NPU2_MISC_DA_LEN_8B, reg);
- /*
- * setup page size = 64k
- *
- * OS type is set to AIX: opal also runs with 2 pages per interrupt,
- * so to cover the max offset for 35 levels of interrupt, we need
- * bits 41 to 46, which is what the AIX setting does. There's no
- * other meaning for that AIX setting.
- */
- reg = npu2_scom_read(p->chip_id, p->xscom_base, NPU2_MISC_CFG,
- NPU2_MISC_DA_LEN_8B);
- reg |= NPU2_MISC_CFG_IPI_PS;
- reg &= ~NPU2_MISC_CFG_IPI_OS;
- npu2_scom_write(p->chip_id, p->xscom_base, NPU2_MISC_CFG,
- NPU2_MISC_DA_LEN_8B, reg);
+ uint64_t reg;
/* enable translation interrupts for all bricks */
reg = npu2_scom_read(p->chip_id, p->xscom_base, NPU2_MISC_IRQ_ENABLE2,
@@ -1708,7 +1672,6 @@ int npu2_opencapi_init_npu(struct npu2 *npu)
{
struct npu2_dev *dev;
uint64_t reg[2];
- int rc;
assert(platform.ocapi);
read_nvram_training_state();
@@ -1741,10 +1704,7 @@ int npu2_opencapi_init_npu(struct npu2 *npu)
address_translation_config(npu->chip_id, npu->xscom_base, dev->brick_index);
}
- /* Procedure 13.1.3.10 - Interrupt Configuration */
- rc = setup_irq(npu);
- if (rc)
- goto failed;
+ enable_xsl_irq(npu);
for (int i = 0; i < npu->total_devices; i++) {
dev = &npu->devices[i];
@@ -1754,8 +1714,6 @@ int npu2_opencapi_init_npu(struct npu2 *npu)
}
return 0;
-failed:
- return -1;
}
static const struct phb_ops npu2_opencapi_ops = {
diff --git a/include/npu2.h b/include/npu2.h
index 86a449eb..6c73679f 100644
--- a/include/npu2.h
+++ b/include/npu2.h
@@ -170,7 +170,6 @@ struct npu2 {
uint64_t mm_base;
uint64_t mm_size;
uint32_t base_lsi;
- uint32_t irq_base;
uint32_t total_devices;
struct npu2_dev *devices;
enum phys_map_type gpu_map_type;
--
2.19.1
More information about the Skiboot
mailing list