[Skiboot] [PATCH v2 1/5] npu2-opencapi: Use presence detection
Frederic Barrat
fbarrat at linux.ibm.com
Thu May 24 03:25:41 AEST 2018
From: Frederic Barrat <fbarrat at linux.vnet.ibm.com>
Presence detection is not part of the opencapi specification. So each
platform may choose to implement it the way it wants.
All current platforms implement it through an i2c device where we can
query a pin to know if a device is connected or not. ZZ and Zaius have
a similar design and even use the same i2c information and pin
numbers.
However, presence detection on older ZZ planar (older than v4) doesn't
work, so we don't activate it for now, until our lab systems are
upgraded and it's better tested.
Presence detection on witherspoon is still being worked on. It's
shaping up to be quite different, so we may have to revisit the topic
in a later patch.
Signed-off-by: Frederic Barrat <fbarrat at linux.vnet.ibm.com>
---
v2:
define platform_ocapi with inline literals, to match existing style
rework a few comments
core/platform.c | 11 ++++-
hw/npu2-opencapi.c | 121 ++++++++++++++++++++++++++++++++++++++---------
include/platform.h | 4 ++
platforms/astbmc/zaius.c | 6 ++-
platforms/ibm-fsp/zz.c | 10 +++-
5 files changed, 127 insertions(+), 25 deletions(-)
diff --git a/core/platform.c b/core/platform.c
index f09ea3c1..92b118ba 100644
--- a/core/platform.c
+++ b/core/platform.c
@@ -175,7 +175,16 @@ const struct platform_ocapi generic_ocapi = {
.i2c_offset = { 0x3, 0x1, 0x1 },
.i2c_odl0_data = { 0xFD, 0xFD, 0xFF },
.i2c_odl1_data = { 0xBF, 0xBF, 0xFF },
- .odl_phy_swap = true,
+ .i2c_presence_addr = 0x20,
+ .i2c_presence_odl0 = (1 << 2), /* bottom connector */
+ .i2c_presence_odl1 = (1 << 7), /* top connector */
+ /*
+ * The ZZs we typically use for BML/generic platform tend to
+ * have old planars and presence detection is broken there, so
+ * force presence.
+ */
+ .force_presence = true,
+ .odl_phy_swap = true,
};
static struct bmc_platform generic_bmc = {
diff --git a/hw/npu2-opencapi.c b/hw/npu2-opencapi.c
index 2cc776c7..b2bc0628 100644
--- a/hw/npu2-opencapi.c
+++ b/hw/npu2-opencapi.c
@@ -829,6 +829,44 @@ static void reset_ocapi_device(struct npu2_dev *dev)
}
}
+static bool i2c_presence_detect(struct npu2_dev *dev)
+{
+ uint8_t state, data;
+ int rc;
+
+ /*
+ * Opencapi presence detection is done through i2c
+ *
+ * Lagrange platforms (ZZ, Zaius) use the same default mechanism.
+ * Witherspoon will need a specific implementation, TBD.
+ */
+ rc = i2c_request_send(dev->i2c_port_id_ocapi,
+ platform.ocapi->i2c_presence_addr,
+ SMBUS_READ, 0, 1,
+ &state, 1, 120);
+ if (rc) {
+ prlog(PR_ERR, "OCAPI: error detecting link presence: %d\n",
+ rc);
+ return true; /* assume link exists */
+ }
+
+ prlog(PR_DEBUG, "OCAPI: I2C presence detect: 0x%x\n", state);
+
+ switch (dev->index) {
+ case 2:
+ data = platform.ocapi->i2c_presence_odl0;
+ break;
+ case 3:
+ data = platform.ocapi->i2c_presence_odl1;
+ break;
+ default:
+ prlog(PR_ERR, "OCAPI: presence detection on invalid link\n");
+ return true;
+ }
+ /* Presence detect bits are active low */
+ return !(state & data);
+}
+
static int odl_train(uint32_t gcid, uint32_t index, struct npu2_dev *dev)
{
uint64_t reg, config_xscom;
@@ -896,6 +934,20 @@ static int odl_train(uint32_t gcid, uint32_t index, struct npu2_dev *dev)
return OPAL_HARDWARE;
}
+static int64_t npu2_opencapi_get_presence_state(struct pci_slot *slot,
+ uint8_t *val)
+{
+ bool present;
+ struct npu2_dev *dev = phb_to_npu2_dev_ocapi(slot->phb);
+
+ if (platform.ocapi->force_presence)
+ present = true;
+ else
+ present = i2c_presence_detect(dev);
+ *val = present;
+ return OPAL_SUCCESS;
+}
+
static int64_t npu2_opencapi_get_link_state(struct pci_slot *slot, uint8_t *val)
{
struct npu2_dev *dev = phb_to_npu2_dev_ocapi(slot->phb);
@@ -926,9 +978,9 @@ static struct pci_slot *npu2_opencapi_slot_create(struct phb *phb)
return slot;
/* TODO: Figure out other slot functions */
- slot->ops.get_presence_state = NULL;
- slot->ops.get_link_state = npu2_opencapi_get_link_state;
- slot->ops.get_power_state = NULL;
+ slot->ops.get_presence_state = npu2_opencapi_get_presence_state;
+ slot->ops.get_link_state = npu2_opencapi_get_link_state;
+ slot->ops.get_power_state = NULL;
slot->ops.get_attention_state = NULL;
slot->ops.get_latch_state = NULL;
slot->ops.set_power_state = NULL;
@@ -1264,6 +1316,48 @@ static int setup_irq(struct npu2 *p)
#define LINK_TRAINING_RETRIES 5
+static int train_link(int chip_id, struct npu2_dev *dev)
+{
+ bool train;
+ int rc;
+ int retries = LINK_TRAINING_RETRIES;
+
+ if (platform.ocapi->force_presence)
+ train = true;
+ else
+ train = i2c_presence_detect(dev);
+ if (!train) {
+ /*
+ * FIXME: if there's no card on the link, we should consider
+ * powering off the unused lanes to save energy
+ */
+ prlog(PR_INFO, "OCAPI: no card detected on link %d, chip %d\n",
+ dev->index, chip_id);
+ return -1;
+ }
+
+ do {
+ rc = odl_train(chip_id, dev->index, dev);
+ } while (rc != OPAL_SUCCESS && --retries);
+
+ if (rc != OPAL_SUCCESS && retries == 0) {
+ /**
+ * @fwts-label OCAPILinkTrainingFailed
+ * @fwts-advice The OpenCAPI link training procedure failed.
+ * This indicates a hardware or firmware bug. OpenCAPI
+ * functionality will not be available on this link.
+ */
+ prlog(PR_ERR,
+ "OCAPI: Link %d on chip %u failed to train\n",
+ dev->index, chip_id);
+ prlog(PR_ERR, "OCAPI: Final link status: %016llx\n",
+ get_odl_status(chip_id, dev->index));
+ return -1;
+ }
+
+ return 0;
+}
+
static void npu2_opencapi_setup_device(struct dt_node *dn_link, struct npu2 *n,
struct npu2_dev *dev)
{
@@ -1272,7 +1366,6 @@ static void npu2_opencapi_setup_device(struct dt_node *dn_link, struct npu2 *n,
struct pci_slot *slot;
char port_name[17];
uint64_t mm_win[2];
- int retries = LINK_TRAINING_RETRIES;
int rc;
dev_index = dt_prop_get_u32(dn_link, "ibm,npu-link-index");
@@ -1367,27 +1460,11 @@ static void npu2_opencapi_setup_device(struct dt_node *dn_link, struct npu2 *n,
break;
case NPU2_TRAIN_DEFAULT:
- do {
- rc = odl_train(n->chip_id, dev->index, dev);
- } while (rc != OPAL_SUCCESS && --retries);
-
- if (rc != OPAL_SUCCESS && retries == 0) {
- /**
- * @fwts-label OCAPILinkTrainingFailed
- * @fwts-advice The OpenCAPI link training procedure failed.
- * This indicates a hardware or firmware bug. OpenCAPI
- * functionality will not be available on this link.
- */
- prlog(PR_ERR,
- "OCAPI: Link %d on chip %u failed to train\n",
- dev->index, n->chip_id);
- prlog(PR_ERR, "OCAPI: Final link status: %016llx\n",
- get_odl_status(n->chip_id, dev->index));
+ rc = train_link(n->chip_id, dev);
+ if (rc)
goto failed;
- }
otl_enabletx(n->chip_id, n->xscom_base, dev->index);
-
slot = npu2_opencapi_slot_create(&dev->phb_ocapi);
if (!slot) {
/**
diff --git a/include/platform.h b/include/platform.h
index a7776446..6fa016c2 100644
--- a/include/platform.h
+++ b/include/platform.h
@@ -51,6 +51,10 @@ struct platform_ocapi {
uint32_t i2c_offset[3]; /* Offsets on I2C device */
uint8_t i2c_odl0_data[3]; /* Data to reset ODL0 */
uint8_t i2c_odl1_data[3]; /* Data to reset ODL1 */
+ uint8_t i2c_presence_addr; /* I2C address for presence detection */
+ uint8_t i2c_presence_odl0; /* I2C mask for detection on ODL0 */
+ uint8_t i2c_presence_odl1; /* I2C mask for detection on ODL1 */
+ bool force_presence; /* don't use i2c detection */
bool odl_phy_swap; /* Swap ODL1 to use brick 2 rather than
* brick 1 lanes */
};
diff --git a/platforms/astbmc/zaius.c b/platforms/astbmc/zaius.c
index 7678ad12..52b072af 100644
--- a/platforms/astbmc/zaius.c
+++ b/platforms/astbmc/zaius.c
@@ -24,13 +24,17 @@
#include "astbmc.h"
+
const struct platform_ocapi zaius_ocapi = {
.i2c_engine = 1,
.i2c_port = 4,
.i2c_offset = { 0x3, 0x1, 0x1 },
.i2c_odl0_data = { 0xFD, 0xFD, 0xFF },
.i2c_odl1_data = { 0xBF, 0xBF, 0xFF },
- .odl_phy_swap = true,
+ .i2c_presence_addr = 0x20,
+ .i2c_presence_odl0 = (1 << 2), /* bottom connector */
+ .i2c_presence_odl1 = (1 << 7), /* top connector */
+ .odl_phy_swap = true,
};
#define NPU_BASE 0x5011000
diff --git a/platforms/ibm-fsp/zz.c b/platforms/ibm-fsp/zz.c
index 9a849290..6c8411ec 100644
--- a/platforms/ibm-fsp/zz.c
+++ b/platforms/ibm-fsp/zz.c
@@ -34,7 +34,15 @@ const struct platform_ocapi zz_ocapi = {
.i2c_offset = { 0x3, 0x1, 0x1 },
.i2c_odl0_data = { 0xFD, 0xFD, 0xFF },
.i2c_odl1_data = { 0xBF, 0xBF, 0xFF },
- .odl_phy_swap = true,
+ .i2c_presence_addr = 0x20,
+ .i2c_presence_odl0 = (1 << 2), /* bottom connector */
+ .i2c_presence_odl1 = (1 << 7), /* top connector */
+ /*
+ * i2c presence detection is broken on ZZ planar < v4 so we
+ * force the presence until all our systems are upgraded
+ */
+ .force_presence = true,
+ .odl_phy_swap = true,
};
static bool zz_probe(void)
--
2.14.1
More information about the Skiboot
mailing list