[Skiboot] [PATCH v6 2/2] phb4: set PBCQ Tunnel BAR for tunneled operations
Frederic Barrat
fbarrat at linux.vnet.ibm.com
Fri Feb 16 21:55:31 AEDT 2018
Le 14/02/2018 à 16:13, Philippe Bergheaud a écrit :
> P9 supports PCI tunneled operations (atomics and as_notify) that are
> initiated by devices.
>
> A subset of the tunneled operations require a response, that must be
> sent back from the host to the device. For example, an atomic compare
> and swap will return the compare status, as swap will only performed
> in case of success. Similarly, as_notify reports if the target thread
> has been woken up or not, because the operation may fail.
>
> To enable tunneled operations, a device driver must tell the host where
> it expects tunneled operation responses, by setting the PBCQ Tunnel BAR
> Response register with a specific value within the range of its BARs.
>
> This register is currently initialized by enable_capi_mode(). But, as
> tunneled operations may also operate in PCI mode, a new API is required
> to set the PBCQ Tunnel BAR Response register, without switching to CAPI
> mode.
>
> This patch provides two new OPAL calls to get/set the PBCQ Tunnel
> BAR Response register.
>
> Note: as there is only one PBCQ Tunnel BAR register, shared between
> all the devices connected to the same PHB, only one of these devices
> will be able to use tunneled operations, at any time.
>
> Signed-off-by: Philippe Bergheaud <felix at linux.vnet.ibm.com>
> ---
There's a conflict with the opencapi opal call IDs (that this patch also
adds), but other than that:
Reviewed-by: Frederic Barrat <fbarrat at linux.vnet.ibm.com>
> Changelog:
>
> v2: Adjust new OPAL call numbers.
>
> v3: Rebase on skiboot 5.9.6.
> Document new OPAL calls in doc/opal-api.
>
> v4: opal_pci_get_pbcq_tunnel_bar():
> - check that addr parameter is valid
> - update doc/opal-api
> enable_capi_mode():
> - explain why we do not touch an existing tunnel bar value
> - reuse psl tnr addr value verbatim, and shift it by 8
>
> v5: No change.
>
> v6: Rebased on top of Andrew Donnellan's patch
> https://patchwork.ozlabs.org/patch/870252/
> that adds three opal calls, and will probably be accepted
> before this one.
> ---
> core/pci-opal.c | 36 ++++++++++
> .../opal-pci-get-set-pbcq-tunnel-bar-162-163.rst | 76 ++++++++++++++++++++++
> hw/phb4.c | 71 ++++++++++++++++++--
> include/opal-api.h | 7 +-
> include/pci.h | 4 ++
> 5 files changed, 188 insertions(+), 6 deletions(-)
> create mode 100644 doc/opal-api/opal-pci-get-set-pbcq-tunnel-bar-162-163.rst
>
> diff --git a/core/pci-opal.c b/core/pci-opal.c
> index b8aec941..77e965cc 100644
> --- a/core/pci-opal.c
> +++ b/core/pci-opal.c
> @@ -1016,3 +1016,39 @@ static int64_t opal_pci_set_p2p(uint64_t phbid_init, uint64_t phbid_target,
> return OPAL_SUCCESS;
> }
> opal_call(OPAL_PCI_SET_P2P, opal_pci_set_p2p, 4);
> +
> +static int64_t opal_pci_get_pbcq_tunnel_bar(uint64_t phb_id, uint64_t *addr)
> +{
> + struct phb *phb = pci_get_phb(phb_id);
> +
> + if (!opal_addr_valid(addr))
> + return OPAL_PARAMETER;
> +
> + if (!phb)
> + return OPAL_PARAMETER;
> + if (!phb->ops->get_tunnel_bar)
> + return OPAL_UNSUPPORTED;
> +
> + phb_lock(phb);
> + phb->ops->get_tunnel_bar(phb, addr);
> + phb_unlock(phb);
> + return OPAL_SUCCESS;
> +}
> +opal_call(OPAL_PCI_GET_PBCQ_TUNNEL_BAR, opal_pci_get_pbcq_tunnel_bar, 2);
> +
> +static int64_t opal_pci_set_pbcq_tunnel_bar(uint64_t phb_id, uint64_t addr)
> +{
> + struct phb *phb = pci_get_phb(phb_id);
> + int64_t rc;
> +
> + if (!phb)
> + return OPAL_PARAMETER;
> + if (!phb->ops->set_tunnel_bar)
> + return OPAL_UNSUPPORTED;
> +
> + phb_lock(phb);
> + rc = phb->ops->set_tunnel_bar(phb, addr);
> + phb_unlock(phb);
> + return rc;
> +}
> +opal_call(OPAL_PCI_SET_PBCQ_TUNNEL_BAR, opal_pci_set_pbcq_tunnel_bar, 2);
> diff --git a/doc/opal-api/opal-pci-get-set-pbcq-tunnel-bar-162-163.rst b/doc/opal-api/opal-pci-get-set-pbcq-tunnel-bar-162-163.rst
> new file mode 100644
> index 00000000..bbe2264a
> --- /dev/null
> +++ b/doc/opal-api/opal-pci-get-set-pbcq-tunnel-bar-162-163.rst
> @@ -0,0 +1,76 @@
> +OPAL_PCI_GET_PBCQ_TUNNEL_BAR
> +============================
> +::
> +
> + #define OPAL_PCI_GET_PBCQ_TUNNEL_BAR 162
> +
> + int64_t opal_pci_get_pbcq_tunnel_bar(uint64_t phb_id, uint64_t *addr)
> +
> +The host calls this function to read the address out of the PBCQ Tunnel
> +Bar register.
> +
> +Parameters
> +----------
> +::
> +
> + uint64_t phb_id
> + uint64_t *addr
> +
> +``phb_id``
> + The value from the PHB node ibm,opal-phbid property for the device.
> +
> +``addr``
> + A pointer to where the address stored in the PBCQ Tunnel Bar register
> + will be copied.
> +
> +Return Values
> +-------------
> +
> +``OPAL_SUCCESS``
> + Operation was successful
> +
> +``OPAL_PARAMETER``
> + Invalid PHB or addr parameter
> +
> +``OPAL_UNSUPPORTED``
> + Not supported by hardware
> +
> +OPAL_PCI_SET_PBCQ_TUNNEL_BAR
> +============================
> +::
> +
> + #define OPAL_PCI_SET_PBCQ_TUNNEL_BAR 163
> +
> + int64_t opal_pci_set_pbcq_tunnel_bar(uint64_t phb_id, uint64_t addr)
> +
> +The host calls this function to set the PBCQ Tunnel Bar register.
> +
> +Parameters
> +----------
> +::
> +
> + uint64_t phb_id
> + uint64_t addr
> +
> +``phb_id``
> + The value from the PHB node ibm,opal-phbid property for the device.
> +
> +``addr``
> + The value of the address chosen for the PBCQ Tunnel Bar register.
> + If the address is 0, then the PBCQ Tunnel Bar register will be reset.
> + It the address is non-zero, then the PBCQ Tunnel Bar register will be
> + set with ::
> +
> + Bit[0:42] Bit[8:50] of the address
> +
> +Return Values
> +-------------
> +
> +``OPAL_SUCCESS``
> + Operation was successful
> +
> +``OPAL_PARAMETER``
> + Invalid PHB or addr parameter
> +
> +``OPAL_UNSUPPORTED``
> + Not supported by hardware
> diff --git a/hw/phb4.c b/hw/phb4.c
> index 83ee6de8..83cc65b3 100644
> --- a/hw/phb4.c
> +++ b/hw/phb4.c
> @@ -3824,12 +3824,24 @@ static int64_t enable_capi_mode(struct phb4 *p, uint64_t pe_number,
> ((u64)CAPIMASK << 32) | PHB_CAPI_CMPM_ENABLE);
>
> if (!(p->rev == PHB4_REV_NIMBUS_DD10)) {
> - /* PBCQ Tunnel Bar Register
> - * Write Tunnel register to match PSL TNR register
> + /*
> + * PBCQ Tunnel Bar Register
> + *
> + * If set, for example by a driver that may already have
> + * tweaked the tunnel bar, then we do not touch it when
> + * entering capi mode. It's up to the driver to handle it.
> + *
> + * If unset, then we use the PSL_TNR_ADDR[TNR_Addr] reset
> + * value. For fpga/cxl, this code will define the tunnel bar.
> */
> - xscom_write(p->chip_id,
> - p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR,
> - 0x020000E000000000);
> + xscom_read(p->chip_id,
> + p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR, ®);
> + if (!reg) {
> + reg = 0x00020000E0000000ull << 8;
> + xscom_write(p->chip_id,
> + p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR,
> + reg);
> + }
>
> /* PB AIB Hardware Control Register
> * Wait 32 PCI clocks for a credit to become available
> @@ -4076,6 +4088,53 @@ static int64_t phb4_set_capp_recovery(struct phb *phb)
> return 0;
> }
>
> +/*
> + * Return the address out of a PBCQ Tunnel Bar register.
> + */
> +static void phb4_get_tunnel_bar(struct phb *phb, uint64_t *addr)
> +{
> + struct phb4 *p = phb_to_phb4(phb);
> + uint64_t val;
> +
> + xscom_read(p->chip_id, p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR,
> + &val);
> + *addr = val >> 8;
> +}
> +
> +/*
> + * Set PBCQ Tunnel Bar register.
> + * Store addr bits [8:50] in PBCQ Tunnel Bar register bits [0:42].
> + * Note that addr bits [8:50] must also match PSL_TNR_ADDR[8:50].
> + * Reset register if val == 0.
> + *
> + * This interface is required to let device drivers set the Tunnel Bar
> + * value of their choice.
> + *
> + * Compatibility with older versions of linux, that do not set the
> + * Tunnel Bar with phb4_set_tunnel_bar(), is ensured by enable_capi_mode(),
> + * that will set the default value that used to be assumed.
> + */
> +static int64_t phb4_set_tunnel_bar(struct phb *phb, uint64_t addr)
> +{
> + struct phb4 *p = phb_to_phb4(phb);
> + uint64_t mask = 0x00FFFFFFFFFFE000ULL;
> +
> + if (!addr) {
> + /* Reset register */
> + xscom_write(p->chip_id,
> + p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR, addr);
> + return OPAL_SUCCESS;
> + }
> + if ((addr & ~mask))
> + return OPAL_PARAMETER;
> + if (!(addr & mask))
> + return OPAL_PARAMETER;
> +
> + xscom_write(p->chip_id, p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR,
> + (addr & mask) << 8);
> + return OPAL_SUCCESS;
> +}
> +
> static const struct phb_ops phb4_ops = {
> .cfg_read8 = phb4_pcicfg_read8,
> .cfg_read16 = phb4_pcicfg_read16,
> @@ -4111,6 +4170,8 @@ static const struct phb_ops phb4_ops = {
> .set_capi_mode = phb4_set_capi_mode,
> .set_p2p = phb4_set_p2p,
> .set_capp_recovery = phb4_set_capp_recovery,
> + .get_tunnel_bar = phb4_get_tunnel_bar,
> + .set_tunnel_bar = phb4_set_tunnel_bar,
> };
>
> static void phb4_init_ioda3(struct phb4 *p)
> diff --git a/include/opal-api.h b/include/opal-api.h
> index 0bd5f179..ec85ea1d 100644
> --- a/include/opal-api.h
> +++ b/include/opal-api.h
> @@ -215,7 +215,12 @@
> #define OPAL_SENSOR_GROUP_CLEAR 156
> #define OPAL_PCI_SET_P2P 157
> #define OPAL_QUIESCE 158
> -#define OPAL_LAST 158
> +#define OPAL_NPU_SPA_SETUP 159
> +#define OPAL_NPU_SPA_CLEAR_CACHE 160
> +#define OPAL_NPU_TL_SET 161
> +#define OPAL_PCI_GET_PBCQ_TUNNEL_BAR 162
> +#define OPAL_PCI_SET_PBCQ_TUNNEL_BAR 163
> +#define OPAL_LAST 163
>
> #define QUIESCE_HOLD 1 /* Spin all calls at entry */
> #define QUIESCE_REJECT 2 /* Fail all calls with OPAL_BUSY */
> diff --git a/include/pci.h b/include/pci.h
> index 508ebf45..cc890118 100644
> --- a/include/pci.h
> +++ b/include/pci.h
> @@ -333,6 +333,10 @@ struct phb_ops {
> /* PCI peer-to-peer setup */
> void (*set_p2p)(struct phb *phb, uint64_t mode, uint64_t flags,
> uint16_t pe_number);
> +
> + /* Get/set PBCQ Tunnel BAR register */
> + void (*get_tunnel_bar)(struct phb *phb, uint64_t *addr);
> + int64_t (*set_tunnel_bar)(struct phb *phb, uint64_t addr);
> };
>
> enum phb_type {
>
More information about the Skiboot
mailing list