[Skiboot] [PATCH v4 08/10] npu2-opencapi: Add OpenCAPI OPAL API calls
Andrew Donnellan
andrew.donnellan at au1.ibm.com
Wed Feb 7 17:41:58 AEDT 2018
From: Frederic Barrat <fbarrat at linux.vnet.ibm.com>
Add three OPAL API calls that are required by the ocxl driver.
- OPAL_NPU_SPA_SETUP
The Shared Process Area (SPA) is a table containing one entry (a
"Process Element") per memory context which can be accessed by the
OpenCAPI device.
- OPAL_NPU_SPA_CLEAR_CACHE
The NPU keeps a cache of recently accessed memory contexts. When a
Process Element is removed from the SPA, the cache for the link must be
cleared.
- OPAL_NPU_TL_SET
The Transaction Layer specification defines several templates for
messages to be exchanged on the link. During link setup, the host and
device must negotiate what templates are supported on both sides and at
what rates those messages can be sent.
Signed-off-by: Frederic Barrat <fbarrat at linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan at au1.ibm.com>
---
doc/opal-api/opal-npu2-opencapi-159-160-161.rst | 126 ++++++++++-
hw/npu2-opencapi.c | 206 +++++++++++++++++-
include/npu2-regs.h | 4 +-
include/opal-api.h | 5 +-
4 files changed, 340 insertions(+), 1 deletion(-)
create mode 100644 doc/opal-api/opal-npu2-opencapi-159-160-161.rst
diff --git a/doc/opal-api/opal-npu2-opencapi-159-160-161.rst b/doc/opal-api/opal-npu2-opencapi-159-160-161.rst
new file mode 100644
index 000000000000..4db3d3e8961e
--- /dev/null
+++ b/doc/opal-api/opal-npu2-opencapi-159-160-161.rst
@@ -0,0 +1,126 @@
+.. _OPAL_NPU_SPA_SETUP:
+
+OPAL_NPU_SPA_SETUP
+==================
+
+OpenCAPI devices only.
+
+Sets up a Shared Process Area (SPA) with the Shared Process Area
+Pointer (SPAP) set to the provided address `addr`, and sets the OTL PE
+mask (used for PASID to PE handle conversion) to `PE_mask`.
+
+If `addr` is NULL, the SPA will be disabled. `addr` must be 4K aligned.
+
+Parameters
+----------
+::
+
+ uint64_t phb_id
+ int bdfn
+ uint64_t addr
+ uint64_t PE_mask
+
+``phb_id``
+ OPAL ID of PHB
+
+``bdfn``
+ Bus-Device-Function number of OpenCAPI AFU
+
+``addr``
+ Address of Shared Process Area, or NULL to disable SPA. Must be 4K aligned.
+
+``PE_mask``
+ Process Element mask for PASID to PE handle conversion
+
+Return Values
+-------------
+
+OPAL_SUCCESS
+ SPAP and PE mask were successfully set
+
+OPAL_PARAMETER
+ A provided parameter was invalid
+
+OPAL_BUSY
+ SPA is already enabled (or if addr is NULL, SPA is already disabled)
+
+.. _OPAL_NPU_SPA_CLEAR_CACHE:
+
+OPAL_NPU_SPA_CLEAR_CACHE
+========================
+
+OpenCAPI devices only.
+
+Invalidates the Process Element with the given `PE_handle` from the NPU's SPA cache.
+
+Parameters
+----------
+::
+
+ uint64_t phb_id
+ uint32_t bdfn
+ uint64_t PE_handle
+
+``phb_id``
+ OPAL ID of PHB
+
+``bdfn``
+ Bus-Device-Function number of OpenCAPI AFU
+
+``PE_handle``
+ Handle of Process Element being cleared from SPA cache
+
+Return Values
+-------------
+
+OPAL_SUCCESS
+ PE was successfully cleared from SPA cache
+
+OPAL_PARAMETER
+ A provided parameter was invalid
+
+OPAL_BUSY
+ XSLO is currently invalidating a previously requested entry
+
+.. _OPAL_NPU_TL_SET:
+
+OPAL_NPU_TL_SET
+===============
+
+OpenCAPI devices only.
+
+Update the NPU OTL configuration with device capabilities.
+
+Parameters
+----------
+::
+
+ uint64_t phb_id
+ uint32_t bdfn
+ long capabilities
+ uint64_t rate_phys
+ int rate_sz
+
+``phb_id``
+ OPAL ID of PHB
+
+``bdfn``
+ Bus-Device-Function number of OpenCAPI AFU
+
+``capabilities``
+ Bitmap of TL templates the device can receive
+
+``rate_phys``
+ Physical address of rates buffer
+
+``rate_sz``
+ Size of rates buffer (must be equal to 32)
+
+Return Values
+-------------
+
+OPAL_SUCCESS
+ OTL configuration was successfully updated
+
+OPAL_PARAMETER
+ A provided parameter was invalid
diff --git a/hw/npu2-opencapi.c b/hw/npu2-opencapi.c
index c4e263c6d57f..a2bfea8a04cd 100644
--- a/hw/npu2-opencapi.c
+++ b/hw/npu2-opencapi.c
@@ -54,6 +54,9 @@
#define NPU_IRQ_LEVELS 35
#define NPU_IRQ_LEVELS_XSL 23
+#define MAX_PE_HANDLE ((1 << 15) - 1)
+#define TL_MAX_TEMPLATE 63
+#define TL_RATE_BUF_SIZE 32
static const struct phb_ops npu2_opencapi_ops;
@@ -1470,3 +1473,206 @@ static const struct phb_ops npu2_opencapi_ops = {
.set_capp_recovery = NULL,
.tce_kill = NULL,
};
+
+static int64_t opal_npu_spa_setup(uint64_t phb_id, uint32_t __unused bdfn,
+ uint64_t addr, uint64_t PE_mask)
+{
+ uint64_t stack, block, offset, reg;
+ struct phb *phb = pci_get_phb(phb_id);
+ struct npu2_dev *dev;
+ int rc;
+
+ if (!phb || phb->phb_type != phb_type_npu_v2_opencapi)
+ return OPAL_PARAMETER;
+
+ /* 4k aligned */
+ if (addr & 0xFFF)
+ return OPAL_PARAMETER;
+
+ if (PE_mask > 15)
+ return OPAL_PARAMETER;
+
+ dev = phb_to_npu2_dev_ocapi(phb);
+ if (!dev)
+ return OPAL_PARAMETER;
+
+ block = index_to_block(dev->index);
+ stack = index_to_stack(dev->index);
+ if (block == NPU2_BLOCK_OTL1)
+ offset = NPU2_XSL_PSL_SPAP_A1;
+ else
+ offset = NPU2_XSL_PSL_SPAP_A0;
+
+
+ lock(&dev->npu->lock);
+ /*
+ * set the SPAP used by the device
+ */
+ reg = npu2_scom_read(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_REG_OFFSET(stack, NPU2_BLOCK_XSL, offset),
+ NPU2_MISC_DA_LEN_8B);
+ if ((addr && (reg & NPU2_XSL_PSL_SPAP_EN)) ||
+ (!addr && !(reg & NPU2_XSL_PSL_SPAP_EN))) {
+ rc = OPAL_BUSY;
+ goto out;
+ }
+ /* SPA is disabled by passing a NULL address */
+ reg = addr;
+ if (addr)
+ reg = addr | NPU2_XSL_PSL_SPAP_EN;
+
+ npu2_scom_write(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_REG_OFFSET(stack, NPU2_BLOCK_XSL, offset),
+ NPU2_MISC_DA_LEN_8B, reg);
+
+ /*
+ * set the PE mask that the OS uses for PASID -> PE handle
+ * conversion
+ */
+ reg = npu2_scom_read(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_OTL_CONFIG0(stack, block), NPU2_MISC_DA_LEN_8B);
+ reg &= ~NPU2_OTL_CONFIG0_PE_MASK;
+ reg |= (PE_mask << (63-7));
+ npu2_scom_write(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_OTL_CONFIG0(stack, block), NPU2_MISC_DA_LEN_8B,
+ reg);
+ rc = OPAL_SUCCESS;
+out:
+ unlock(&dev->npu->lock);
+ return rc;
+}
+opal_call(OPAL_NPU_SPA_SETUP, opal_npu_spa_setup, 4);
+
+static int64_t opal_npu_spa_clear_cache(uint64_t phb_id, uint32_t __unused bdfn,
+ uint64_t PE_handle)
+{
+ uint64_t cc_inv, stack, block, reg, rc;
+ uint32_t retries = 5;
+ struct phb *phb = pci_get_phb(phb_id);
+ struct npu2_dev *dev;
+
+ if (!phb || phb->phb_type != phb_type_npu_v2_opencapi)
+ return OPAL_PARAMETER;
+
+ if (PE_handle > MAX_PE_HANDLE)
+ return OPAL_PARAMETER;
+
+ dev = phb_to_npu2_dev_ocapi(phb);
+ if (!dev)
+ return OPAL_PARAMETER;
+
+ block = index_to_block(dev->index);
+ stack = index_to_stack(dev->index);
+ cc_inv = NPU2_REG_OFFSET(stack, NPU2_BLOCK_XSL, NPU2_XSL_PSL_LLCMD_A0);
+
+ lock(&dev->npu->lock);
+ reg = npu2_scom_read(dev->npu->chip_id, dev->npu->xscom_base, cc_inv,
+ NPU2_MISC_DA_LEN_8B);
+ if (reg & PPC_BIT(16)) {
+ rc = OPAL_BUSY;
+ goto out;
+ }
+
+ reg = PE_handle | PPC_BIT(15);
+ if (block == NPU2_BLOCK_OTL1)
+ reg |= PPC_BIT(48);
+ npu2_scom_write(dev->npu->chip_id, dev->npu->xscom_base, cc_inv,
+ NPU2_MISC_DA_LEN_8B, reg);
+
+ rc = OPAL_HARDWARE;
+ while (retries--) {
+ reg = npu2_scom_read(dev->npu->chip_id, dev->npu->xscom_base,
+ cc_inv, NPU2_MISC_DA_LEN_8B);
+ if (!(reg & PPC_BIT(16))) {
+ rc = OPAL_SUCCESS;
+ break;
+ }
+ /* the bit expected to flip in less than 200us */
+ time_wait_us(200);
+ }
+out:
+ unlock(&dev->npu->lock);
+ return rc;
+}
+opal_call(OPAL_NPU_SPA_CLEAR_CACHE, opal_npu_spa_clear_cache, 3);
+
+static int get_template_rate(unsigned int templ, char *rate_buf)
+{
+ int shift, idx, val;
+
+ /*
+ * Each rate is encoded over 4 bits (0->15), with 15 being the
+ * slowest. The buffer is a succession of rates for all the
+ * templates. The first 4 bits are for template 63, followed
+ * by 4 bits for template 62, ... etc. So the rate for
+ * template 0 is at the very end of the buffer.
+ */
+ idx = (TL_MAX_TEMPLATE - templ) / 2;
+ shift = 4 * (1 - ((TL_MAX_TEMPLATE - templ) % 2));
+ val = rate_buf[idx] >> shift;
+ return val;
+}
+
+static bool is_template_supported(unsigned int templ, long capabilities)
+{
+ return !!(capabilities & (1ull << templ));
+}
+
+static int64_t opal_npu_tl_set(uint64_t phb_id, uint32_t bdfn,
+ long capabilities, uint64_t rate_phys, int rate_sz)
+{
+ struct phb *phb = pci_get_phb(phb_id);
+ struct npu2_dev *dev;
+ uint64_t stack, block, reg, templ_rate;
+ int i, rate_pos;
+ char *rate = (char *) rate_phys;
+
+ if (!phb || phb->phb_type != phb_type_npu_v2_opencapi)
+ return OPAL_PARAMETER;
+ if (!opal_addr_valid(rate) || rate_sz != TL_RATE_BUF_SIZE)
+ return OPAL_PARAMETER;
+
+ dev = phb_to_npu2_dev_ocapi(phb);
+ if (!dev)
+ return OPAL_PARAMETER;
+
+ block = index_to_block(dev->index);
+ stack = index_to_stack(dev->index);
+ /*
+ * The 'capabilities' argument defines what TL template the
+ * device can receive. OpenCAPI 3.0 and 4.0 define 64 templates, so
+ * that's one bit per template.
+ *
+ * For each template, the device processing time may vary, so
+ * the device advertises at what rate a message of a given
+ * template can be sent. That's encoded in the 'rate' buffer.
+ *
+ * On P9, NPU only knows about TL templates 0 -> 3.
+ * Per the spec, template 0 must be supported.
+ */
+ if (!is_template_supported(0, capabilities))
+ return OPAL_PARAMETER;
+
+ reg = npu2_scom_read(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_OTL_CONFIG1(stack, block),
+ NPU2_MISC_DA_LEN_8B);
+ reg &= ~(NPU2_OTL_CONFIG1_TX_TEMP1_EN | NPU2_OTL_CONFIG1_TX_TEMP3_EN |
+ NPU2_OTL_CONFIG1_TX_TEMP1_EN);
+ for (i = 0; i < 4; i++) {
+ /* Skip template 0 as it is implicitly enabled */
+ if (i && is_template_supported(i, capabilities))
+ reg |= PPC_BIT(i);
+ /* The tx rate should still be set for template 0 */
+ templ_rate = get_template_rate(i, rate);
+ rate_pos = 8 + i * 4;
+ reg = SETFIELD(PPC_BITMASK(rate_pos, rate_pos + 3), reg,
+ templ_rate);
+ }
+ npu2_scom_write(dev->npu->chip_id, dev->npu->xscom_base,
+ NPU2_OTL_CONFIG1(stack, block), NPU2_MISC_DA_LEN_8B,
+ reg);
+ prlog(PR_DEBUG, "OCAPI: Link %llx:%x, TL conf1 register set to %llx\n",
+ phb_id, bdfn, reg);
+ return OPAL_SUCCESS;
+}
+opal_call(OPAL_NPU_TL_SET, opal_npu_tl_set, 5);
diff --git a/include/npu2-regs.h b/include/npu2-regs.h
index 71c8d8f07af0..6efab0843eca 100644
--- a/include/npu2-regs.h
+++ b/include/npu2-regs.h
@@ -321,6 +321,7 @@ void npu2_scom_write(uint64_t gcid, uint64_t scom_base,
#define NPU2_NTL_DL_CLK_CTRL(ndev) NPU2_DL_REG_OFFSET(ndev, 0x001C)
/* OpenCAPI - XSL registers */
+#define NPU2_XSL_PSL_LLCMD_A0 0x008
#define NPU2_XSL_PSL_SCNTL_A0 0x010
#define NPU2_XSL_PSL_SCNTL_A0_MULTI_AFU_DIAL PPC_BIT(0)
#define NPU2_XSL_DEF 0x040
@@ -328,6 +329,9 @@ void npu2_scom_write(uint64_t gcid, uint64_t scom_base,
#define NPU2_XSL_GP_BLOOM_FILTER_ENABLE PPC_BIT(16)
#define NPU2_XSL_WRAP_CFG 0x0C0
#define NPU2_XSL_WRAP_CFG_XSLO_CLOCK_ENABLE PPC_BIT(0)
+#define NPU2_XSL_PSL_SPAP_A0 0
+#define NPU2_XSL_PSL_SPAP_A1 0x18
+#define NPU2_XSL_PSL_SPAP_EN PPC_BIT(63)
/* OpenCAPI - OTL registers */
#define NPU2_OTL_CONFIG0(stack, block) NPU2_REG_OFFSET(stack, block, 0x000)
diff --git a/include/opal-api.h b/include/opal-api.h
index f0ed5f6c69db..1496f389ba24 100644
--- a/include/opal-api.h
+++ b/include/opal-api.h
@@ -215,7 +215,10 @@
#define OPAL_SENSOR_GROUP_CLEAR 156
#define OPAL_PCI_SET_P2P 157
#define OPAL_QUIESCE 158
-#define OPAL_LAST 158
+#define OPAL_NPU_SPA_SETUP 159
+#define OPAL_NPU_SPA_CLEAR_CACHE 160
+#define OPAL_NPU_TL_SET 161
+#define OPAL_LAST 161
#define QUIESCE_HOLD 1 /* Spin all calls at entry */
#define QUIESCE_REJECT 2 /* Fail all calls with OPAL_BUSY */
--
git-series 0.9.1
More information about the Skiboot
mailing list