[Skiboot] [PATCH v2 4/5] skiboot: Enable opal calls to init/start/stop IMC Trace mode
Anju T Sudhakar
anju at linux.vnet.ibm.com
Wed Dec 12 17:15:44 AEDT 2018
Patch to enhance the imc opal call to support and handle trace_imc mode.
To initialize the trace-mode, TRACE_IMC_SCOM value is written to
TRACE_IMC_ADDR of the respective core.
TRACE_IMC_SCOM is a 64bit value, and each bit represent the following:
0:1 : SAMPSEL
2:33 : CPMC_LOAD
34:40 : CPMC1SEL
41:47 : CPMC2SEL
48:50 : BUFFERSIZE
51:63 : RESERVED
For the nonce the value for TRACE_IMC_SCOM is hard coded.
During initialization htm_mode is disabled, and enabled only at start.
The opal calls to start/stop the counters, will write CORE_IMC_HTM_MODE_ENABLE/
CORE_IMC_HTM_MODE_DISABLE respectively to the htm_scom_index of the desired
cores.
Additional switch cases are added to the current opal calls to start/stop
the counters for trace-mode.
Signed-off-by: Anju T Sudhakar <anju at linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy at linux.vnet.ibm.com>
Cc: Akshay Adiga <akshay.adiga at linux.vnet.ibm.com>
---
hw/imc.c | 103 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 103 insertions(+)
diff --git a/hw/imc.c b/hw/imc.c
index 3392eaf1..40c64d58 100644
--- a/hw/imc.c
+++ b/hw/imc.c
@@ -22,6 +22,15 @@
#include <device.h>
#include <p9_stop_api.H>
+/*
+ * IMC trace scom values
+ */
+#define samplesel 1 /* select cpmc2 */
+#define cpmcload 0xfa /* Value to be loaded into cpmc2 at sampling start */
+#define cpmc1sel 2 /* Event: CPM_CCYC */
+#define cpmc2sel 2 /* Event: CPM_32MHZ_CYC */
+#define buffersize 0 /* b’000’- 4K entries * 64 per entry = 256K buffersize */
+
/*
* Nest IMC PMU names along with their bit values as represented in the
* imc_chip_avl_vector(in struct imc_chip_cb, look at include/imc.h).
@@ -264,6 +273,8 @@ static int get_imc_device_type(struct dt_node *node)
return IMC_COUNTER_CORE;
case IMC_COUNTER_THREAD:
return IMC_COUNTER_THREAD;
+ case IMC_COUNTER_TRACE:
+ return IMC_COUNTER_TRACE;
default:
break;
}
@@ -283,11 +294,23 @@ static bool is_nest_node(struct dt_node *node)
static bool is_imc_device_type_supported(struct dt_node *node)
{
u32 val = get_imc_device_type(node);
+ struct proc_chip *chip = get_chip(this_cpu()->chip_id);
+ uint64_t pvr;
if ((val == IMC_COUNTER_CHIP) || (val == IMC_COUNTER_CORE) ||
(val == IMC_COUNTER_THREAD))
return true;
+ if (val == IMC_COUNTER_TRACE) {
+ pvr = mfspr(SPR_PVR);
+ /*
+ * Trace mode is supported in Nimbus DD2.2
+ * and later versions.
+ */
+ if ((chip->type == PROC_CHIP_P9_NIMBUS) &&
+ (PVR_VERS_MAJ(pvr) == 2) && (PVR_VERS_MIN(pvr) >= 2))
+ return true;
+ }
return false;
}
@@ -644,6 +667,8 @@ static int64_t opal_imc_counters_init(uint32_t type, uint64_t addr, uint64_t cpu
int port_id, phys_core_id;
int ret;
uint32_t scoms;
+ uint64_t trace_scom_val = TRACE_IMC_SCOM(samplesel, cpmcload,
+ cpmc1sel, cpmc2sel, buffersize);
switch (type) {
case OPAL_IMC_COUNTERS_NEST:
@@ -738,6 +763,53 @@ static int64_t opal_imc_counters_init(uint32_t type, uint64_t addr, uint64_t cpu
return OPAL_HARDWARE;
}
return OPAL_SUCCESS;
+ case OPAL_IMC_COUNTERS_TRACE:
+ if (!c)
+ return OPAL_PARAMETER;
+
+ phys_core_id = cpu_get_core_index(c);
+ port_id = phys_core_id % 4;
+
+ if (proc_chip_quirks & QUIRK_MAMBO_CALLOUTS)
+ return OPAL_SUCCESS;
+
+ if (has_deep_states) {
+ if (wakeup_engine_state == WAKEUP_ENGINE_PRESENT) {
+ struct proc_chip *chip = get_chip(c->chip_id);
+
+ prlog(PR_INFO, "Configuring stopapi for IMC trace-mode\n");
+ scoms = XSCOM_ADDR_P9_EC(phys_core_id, TRACE_IMC_ADDR);
+ ret = p9_stop_save_scom((void *)chip->homer_base, scoms,
+ trace_scom_val,
+ P9_STOP_SCOM_REPLACE,
+ P9_STOP_SECTION_CORE_SCOM);
+ if (ret) {
+ prerror("IMC trace_mode stopapi ret = %d, scoms = %x (core id = %x)\n", ret, scoms, phys_core_id);
+ if (ret != STOP_SAVE_SCOM_ENTRY_UPDATE_FAILED)
+ wakeup_engine_state = WAKEUP_ENGINE_FAILED;
+ else
+ prerror("SCOM entries are full\n");
+ return OPAL_HARDWARE;
+ }
+ } else {
+ prerror("IMC: TRACE: Wakeup engine in error state!");
+ return OPAL_HARDWARE;
+ }
+ }
+ if (xscom_write(c->chip_id,
+ XSCOM_ADDR_P9_EP(phys_core_id, htm_scom_index[port_id]),
+ (u64)CORE_IMC_HTM_MODE_DISABLE)) {
+ prerror("IMC: error in xscom_write for htm mode\n");
+ return OPAL_HARDWARE;
+ }
+ if (xscom_write(c->chip_id,
+ XSCOM_ADDR_P9_EC(phys_core_id,
+ TRACE_IMC_ADDR), trace_scom_val)) {
+ prerror("IMC: error in xscom_write for trace mode\n");
+ return OPAL_HARDWARE;
+ }
+ return OPAL_SUCCESS;
+
}
return OPAL_SUCCESS;
@@ -797,6 +869,21 @@ static int64_t opal_imc_counters_start(uint32_t type, uint64_t cpu_pir)
return OPAL_HARDWARE;
}
+ return OPAL_SUCCESS;
+ case OPAL_IMC_COUNTERS_TRACE:
+ phys_core_id = cpu_get_core_index(c);
+ port_id = phys_core_id % 4;
+
+ if (proc_chip_quirks & QUIRK_MAMBO_CALLOUTS)
+ return OPAL_SUCCESS;
+
+ if (xscom_write(c->chip_id,
+ XSCOM_ADDR_P9_EP(phys_core_id,
+ htm_scom_index[port_id]),
+ (u64)CORE_IMC_HTM_MODE_ENABLE)) {
+ prerror("IMC OPAL_start: error in xscom_write for htm_mode\n");
+ return OPAL_HARDWARE;
+ }
return OPAL_SUCCESS;
}
@@ -857,6 +944,22 @@ static int64_t opal_imc_counters_stop(uint32_t type, uint64_t cpu_pir)
}
return OPAL_SUCCESS;
+ case OPAL_IMC_COUNTERS_TRACE:
+ phys_core_id = cpu_get_core_index(c);
+ port_id = phys_core_id % 4;
+
+ if (proc_chip_quirks & QUIRK_MAMBO_CALLOUTS)
+ return OPAL_SUCCESS;
+
+ if (xscom_write(c->chip_id,
+ XSCOM_ADDR_P9_EP(phys_core_id,
+ htm_scom_index[port_id]),
+ (u64)CORE_IMC_HTM_MODE_DISABLE)) {
+ prerror("IMC: error in xscom_write for htm_mode\n");
+ return OPAL_HARDWARE;
+ }
+ return OPAL_SUCCESS;
+
}
return OPAL_SUCCESS;
--
2.17.1
More information about the Skiboot
mailing list