[Skiboot] [PATCH] external: NPU hardware procedure script

[Russell Currey]

Performing NPU hardware procedures requires some config space magic.
Put all that magic into a script, so you can just specify the target
device and the procedure number.

Signed-off-by: Russell Currey <ruscur at russell.cc>
---
 external/npu/run_procedure.sh | 119 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 119 insertions(+)
 create mode 100755 external/npu/run_procedure.sh

diff --git a/external/npu/run_procedure.sh b/external/npu/run_procedure.sh
new file mode 100755
index 0000000..f61ec8d
--- /dev/null
+++ b/external/npu/run_procedure.sh
@@ -0,0 +1,119 @@
+#!/bin/bash
+
+# Copyright 2016 IBM Corp.
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# 	http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or
+# implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+function usage() {
+	echo -e "$0: run a NPU hardware procedure (requires root)\n"
+	echo -e "Usage: $0 <PCI bdfn> <procedure number>\n"
+	echo -e "Example: $0 0008:00:01.1 1"
+	echo -e "Procedures are documented in skiboot/doc/nvlink.rst"
+}
+
+function check_root() {
+	if [ "$(id -u)" != "0" ]; then
+		echo -e "Error: $0 must be run as root\n" 1>&2
+		exit 1
+	fi
+}
+
+function check_args() {
+	if [ "$#" -eq 0 ]; then
+		usage
+		exit 1
+	fi
+
+	if [ "$#" -gt 2 ]; then
+		echo -e "Error: too many arguments\n" 1>&2
+		usage
+		exit 1
+	fi
+
+	if [[ "$1" == "-h" || "$1" == "--help" ]]; then
+		usage
+		exit 0
+	fi
+
+	if ! [ "$2" -eq "$2" ] 2>/dev/null; then
+		echo -e "Procedure must be a decimal number\n" 1>&2
+		usage
+		exit 1
+	fi
+
+	if [[ "$2" -lt "0" || "$2" -gt "12" ]]; then
+		echo -e "Invalid procedure number\n" 1>&2
+		usage
+		exit 2
+	fi
+
+	pci_check=$(lspci -s $1)
+	if [[ $? -ne 0 || $pci_check == "" ]]; then
+		echo -e "Invalid PCI device\n" 1>&2
+		usage
+		exit 2
+	fi
+}
+
+function run_procedure() {
+	# Convert procedure number into hex
+	procedure=$(echo "obase=16; $2" | bc)
+
+	# Check the status register to make sure we can run a procedure
+	status=$(setpci -s $1 0x84.L)
+	if [[ $status == 8000000* ]]; then
+		echo "Procedure in progress, try again." 1>&2
+		echo "If that doesn't work, use procedure 0 to abort." 1>&2
+		exit 3
+	fi
+
+	# Start the procedure
+	setpci -s $1 0x88.L=0x0000000$procedure >/dev/null
+	if [ $? -ne 0 ]; then
+		echo "Control register write failed!" 1>&2
+		exit 3
+	fi
+
+	iterations=1
+	while [[ $(setpci -s $1 0x84.L) == 8000000* ]]; do
+		((iterations++))
+	done
+
+	# Check again, procedure should be finished
+	status=$(setpci -s $1 0x84.L)
+
+	echo "Done in $iterations iteration(s)!"
+
+	if [[ $status == 40000000 ]]; then
+		echo "Procedure completed successfully."
+		exit 0
+	elif [[ $status == 40000001 ]]; then
+		echo "Transient failure, try again." 1>&2
+		exit 4
+	elif [[ $status == 40000002 ]]; then
+		echo "Permanent failure, reboot required?" 1>&2
+		exit 5
+	elif [[ $status == 40000003 ]]; then
+		echo "Procedure aborted." 1>&2
+		exit 6
+	elif [[ $status == 40000004 ]]; then
+		echo "Unsupported procedure." 1>&2
+		exit 7
+	fi
+}
+
+check_args "$@"
+check_root
+run_procedure "$1" "$2"
-- 
2.9.2