[PATCH v2 2/2] iio: adc: add Nuvoton NCT720x ADC driver

[Yu-Hsian Yang]

Dear Jonathan Cameron,

Thanks for your comment.

Jonathan Cameron <jic23 at kernel.org> 於 2024年12月9日 週一 上午1:22寫道：
>
> On Tue,  3 Dec 2024 17:15:40 +0800
> Eason Yang <j2anfernee at gmail.com> wrote:
>
> > Add Nuvoton NCT7201/NCT7202 system voltage monitor 12-bit ADC driver
> >
> > NCT7201/NCT7202 supports up to 12 analog voltage monitor inputs and up to
> > 4 SMBus addresses by ADDR pin. Meanwhile, ALERT# hardware event pins for
> > independent alarm signals, and the all threshold values could be set for
> > system protection without any timing delay. It also supports reset input
> > RSTIN# to recover system from a fault condition.
> >
> > Currently, only single-edge mode conversion and threshold events support.
> >
> > Signed-off-by: Eason Yang <j2anfernee at gmail.com>
> Hi Eason,
>
> Given you have some good reviews already I only took a very quick glance
> through.  A few things inline
>
> Jonathan
>
> > diff --git a/drivers/iio/adc/nct720x.c b/drivers/iio/adc/nct720x.c
> > new file mode 100644
> > index 000000000000..b28b5f4d7d70
> > --- /dev/null
> > +++ b/drivers/iio/adc/nct720x.c
>
> > +
> > +static int nct720x_write_event_value(struct iio_dev *indio_dev,
> > +                                  const struct iio_chan_spec *chan,
> > +                                  enum iio_event_type type,
> > +                                  enum iio_event_direction dir,
> > +                                  enum iio_event_info info,
> > +                                  int val, int val2)
> > +{
> > +     struct nct720x_chip_info *chip = iio_priv(indio_dev);
> > +     int index, err = 0;
> > +     long v1, v2, volt;
> > +
> > +     index = nct720x_chan_to_index[chan->address];
> > +     volt = (val * NCT720X_IN_SCALING_FACTOR) / NCT720X_IN_SCALING;
> > +     v1 = volt >> 5;
> > +     v2 = (volt & REG_VIN_LIMIT_LSB_MASK) << 3;
> > +
> > +     if (chan->type != IIO_VOLTAGE)
> > +             return -EOPNOTSUPP;
> > +
> > +     if (info == IIO_EV_INFO_VALUE) {
> > +             if (dir == IIO_EV_DIR_FALLING) {
> > +                     guard(mutex)(&chip->access_lock);
>
> Might as well move this up one level as it is called in both legs.
>

I would remove guard(mutex) up one level.

> > +                     err = regmap_write(chip->regmap, REG_VIN_LOW_LIMIT[index], v1);
> > +                     if (err < 0)
> > +                             dev_err(&indio_dev->dev, "Failed to write REG_VIN%d_LOW_LIMIT\n",
> > +                                     index + 1);
> > +
> > +                     err = regmap_write(chip->regmap, REG_VIN_LOW_LIMIT_LSB[index], v2);
> > +                     if (err < 0)
> > +                             dev_err(&indio_dev->dev, "Failed to write REG_VIN%d_LOW_LIMIT_LSB\n",
> > +                                     index + 1);
> > +
> > +             } else {
> > +                     guard(mutex)(&chip->access_lock);
> > +                     err = regmap_write(chip->regmap, REG_VIN_HIGH_LIMIT[index], v1);
> > +                     if (err < 0)
> > +                             dev_err(&indio_dev->dev, "Failed to write REG_VIN%d_HIGH_LIMIT\n",
> > +                                     index + 1);
> > +
> > +                     err = regmap_write(chip->regmap, REG_VIN_HIGH_LIMIT_LSB[index], v2);
> > +                     if (err < 0)
> > +                             dev_err(&indio_dev->dev, "Failed to write REG_VIN%d_HIGH_LIMIT_LSB\n",
> > +                                     index + 1);
> > +             }
> > +     }
> > +     return err;
> > +}
>
> > +
> > +static const struct iio_info nct720x_info = {
> > +     .read_raw = nct720x_read_raw,
> > +     .read_event_config = nct720x_read_event_config,
> > +     .write_event_config = nct720x_write_event_config,
> > +     .read_event_value = nct720x_read_event_value,
> > +     .write_event_value = nct720x_write_event_value,
>
> Given you are supporting with and without interrupts, should probably pick between
> versions of this that have the event config part and one that doesn't.
>

Sorry, could you give some examples for us to refer.

> > +};
> > +
> > +static const struct nct720x_adc_model_data nct7201_model_data = {
> > +     .model_name = "nct7201",
> > +     .channels = nct7201_channels,
> > +     .num_channels = ARRAY_SIZE(nct7201_channels),
> > +     .vin_max = 8,
> > +};
> > +
> > +static const struct nct720x_adc_model_data nct7202_model_data = {
> > +     .model_name = "nct7202",
> > +     .channels = nct7202_channels,
> > +     .num_channels = ARRAY_SIZE(nct7202_channels),
> > +     .vin_max = 12,
> > +};
> > +
> > +static int nct720x_init_chip(struct nct720x_chip_info *chip)
> > +{
> > +     u8 data[2];
> > +     unsigned int value;
> > +     int err;
> > +
> > +     err = regmap_write(chip->regmap, REG_CONFIGURATION, BIT_CONFIGURATION_RESET);
> > +     if (err) {
> > +             dev_err(&chip->client->dev, "Failed to write REG_CONFIGURATION\n");
> > +             return err;
> > +     }
> > +
> > +     /*
> > +      * After about 25 msecs, the device should be ready and then
> > +      * the Power Up bit will be set to 1. If not, wait for it.
> > +      */
> > +     mdelay(25);
> > +     err  = regmap_read(chip->regmap, REG_BUSY_STATUS, &value);
> > +     if (err < 0)
> > +             return err;
> > +     if (!(value & BIT_PWR_UP))
> > +             return err;
> > +
> > +     /* Enable Channel */
> > +     err = regmap_write(chip->regmap, REG_CHANNEL_ENABLE_1, REG_CHANNEL_ENABLE_1_MASK);
> > +     if (err) {
> > +             dev_err(&chip->client->dev, "Failed to write REG_CHANNEL_ENABLE_1\n");
> > +             return err;
> > +     }
> > +
> > +     if (chip->vin_max == 12) {
> > +             err = regmap_write(chip->regmap, REG_CHANNEL_ENABLE_2, REG_CHANNEL_ENABLE_2_MASK);
> > +             if (err) {
> > +                     dev_err(&chip->client->dev, "Failed to write REG_CHANNEL_ENABLE_2\n");
> > +                     return err;
> > +             }
> > +     }
> > +
> > +     guard(mutex)(&chip->access_lock);
> > +     err  = regmap_read(chip->regmap, REG_CHANNEL_ENABLE_1, &value);
> > +     if (err < 0)
> > +             return err;
> > +     data[0] = (u8)value;
> > +
> > +     err  = regmap_read(chip->regmap, REG_CHANNEL_ENABLE_2, &value);
> > +     if (err < 0)
> > +             return err;
>
> Here I think you can use a bulk read as the registers are next to each other.
>

Generally, registers with 8 bits support Byte format, and registers
with more than 8 bits support Word format.
If transmission a Word command to a register that supports Byte
format, the second byte will get 0xFF.
Here, if we use regmap_bulk_read(), we would get first byte correct
and second byte is wrong 0xff.
I use i2ctransfer to demo it.
root at evb-npcm845:~# i2ctransfer -f -y 5 w1 at 0x1d 0x13 r1
0xff
root at evb-npcm845:~# i2ctransfer -f -y 5 w1 at 0x1d 0x14 r1
0x0f



> > +     data[1] = (u8)value;
> > +
> > +     value = get_unaligned_le16(data);
> > +     chip->vin_mask = value;
> > +
> > +     /* Start monitoring if needed */
> > +     err = regmap_read(chip->regmap, REG_CONFIGURATION, &value);
> > +     if (err < 0) {
> > +             dev_err(&chip->client->dev, "Failed to read REG_CONFIGURATION\n");
> > +             return value;
> > +     }
> > +
> > +     value |= BIT_CONFIGURATION_START;
> > +     err = regmap_write(chip->regmap, REG_CONFIGURATION, value);
> > +     if (err < 0) {
> > +             dev_err(&chip->client->dev, "Failed to write REG_CONFIGURATION\n");
> > +             return err;
> > +     }
> > +
> > +     return 0;
> > +}