[PATCH v13 2/3] i2c: aspeed: support AST2600 i2c new register mode driver

[Ryan Chen]

> Subject: Re: [PATCH v13 2/3] i2c: aspeed: support AST2600 i2c new register
> mode driver
> 
> On Mon, Aug 26, 2024 at 07:50:24AM +0000, Ryan Chen wrote:
> > > On Fri, Aug 23, 2024 at 06:23:54AM +0000, Ryan Chen wrote:
> > > > > On Thu, Aug 22, 2024 at 02:24:26AM +0000, Ryan Chen wrote:
> > > > > > > On Wed, Aug 21, 2024 at 06:43:01AM +0000, Ryan Chen wrote:
> > > > > > > > > On Mon, Aug 19, 2024 at 05:28:49PM +0800, Ryan Chen wrote:
> 
> ...
> 
> > > > > > > > > > +	if (i2c_bus->mode == BUFF_MODE) {
> > > > > > > > > > +		i2c_bus->buf_base =
> > > > > > > > > devm_platform_get_and_ioremap_resource(pdev, 1, &res);
> > > > > > > > > > +		if (!IS_ERR_OR_NULL(i2c_bus->buf_base))
> > > > > > > > > > +			i2c_bus->buf_size = resource_size(res) / 2;
> > > > > > > > > > +		else
> > > > > > > > > > +			i2c_bus->mode = BYTE_MODE;
> > > > > > > > >
> > > > > > > > > What's wrong with positive conditional? And is it even
> > > > > > > > > possible to have NULL here?
> > > > > > > > >
> > > > > > > > Yes, if dtsi fill not following yaml example have reg 1,
> > > > > > > > that will failure at buffer
> > > > > > > mode.
> > > > > > > > And I can swith to byte mode.
> > > > > > > >
> > > > > > > > reg = <0x80 0x80>, <0xc00 0x20>;
> > > > > > >
> > > > > > > I was asking about if (!IS_ERR_OR_NULL(...)) line:
> > > > > > > 1) Why 'if (!foo) {} else {}' instead of 'if (foo) {} else {}'?
> > > > > > I will update to following.
> > > > > > 		if (IS_ERR(i2c_bus->buf_base))
> > > > > > 			i2c_bus->mode = BYTE_MODE;
> > > > > > 		else
> > > > > > 			i2c_bus->buf_size = resource_size(res) / 2;
> > > > > >
> > > > > > > 2) Why _NULL?
> > > > > > 	If dtsi file is claim only 1 reg offset. reg = <0x80 0x80>;
> > > > > > that will goto byte
> > > > > mode.
> > > > > > 	reg = <0x80 0x80>, <0xc00 0x20>; can support buffer mode.
> > > > > > 	due to 2nd is buffer register offset.
> > > > >
> > > > > I have asked why IS_ERR_OR_NULL() and not IS_ERR().
> > > > >
> > > > OH, I will doing by this.
> > > > 		if (IS_ERR_OR_NULL(i2c_bus->buf_base))
> > >
> > > The question about _NULL remains unanswered...
> > Sorry, I may not catch your point.
> > So, Do you mean I should passive coding by following?
> 
> No. I already mentioned that in one of the previous mails.
> Why do you use IS_ERR_OR_NULL() and not IS_ERR()?
> 
> You should understand your code better than me :-)
Understood, I will change to 
	if (IS_ERR(i2c_bus->buf_base))
		i2c_bus->mode = BYTE_MODE;
	else
		i2c_bus->buf_size = resource_size(res) / 2;

> > If (i2c_bus->buf_base > 0)
> > 	i2c_bus->buf_size = resource_size(res) / 2; else
> >     i2c_bus->mode = BYTE_MODE;
> >
> > > > 			i2c_bus->mode = BYTE_MODE;
> > > > 		else
> > > > 			i2c_bus->buf_size = resource_size(res) / 2;
> 
> --
> With Best Regards,
> Andy Shevchenko
>