[PATCH linux dev-6.5 v1 2/2] peci: Add peci-npcm controller driver
Tomer Maimon
tmaimon77 at gmail.com
Sun Oct 1 22:12:18 AEDT 2023
Add support for Nuvoton NPCM BMC hardware to the Platform Environment
Control Interface (PECI) subsystem.
Signed-off-by: Tomer Maimon <tmaimon77 at gmail.com>
---
drivers/peci/controller/Kconfig | 16 ++
drivers/peci/controller/Makefile | 1 +
drivers/peci/controller/peci-npcm.c | 298 ++++++++++++++++++++++++++++
3 files changed, 315 insertions(+)
create mode 100644 drivers/peci/controller/peci-npcm.c
diff --git a/drivers/peci/controller/Kconfig b/drivers/peci/controller/Kconfig
index 2fc5e2abb74a..4f9c245ad042 100644
--- a/drivers/peci/controller/Kconfig
+++ b/drivers/peci/controller/Kconfig
@@ -16,3 +16,19 @@ config PECI_ASPEED
This driver can also be built as a module. If so, the module will
be called peci-aspeed.
+
+config PECI_NPCM
+ tristate "Nuvoton NPCM PECI support"
+ depends on ARCH_NPCM || COMPILE_TEST
+ depends on OF
+ select REGMAP_MMIO
+ help
+ This option enables PECI controller driver for Nuvoton NPCM7XX
+ and NPCM8XX SoCs. It allows BMC to discover devices connected
+ to it and communicate with them using PECI protocol.
+
+ Say Y here if you want support for the Platform Environment Control
+ Interface (PECI) bus adapter driver on the Nuvoton NPCM SoCs.
+
+ This support is also available as a module. If so, the module
+ will be called peci-npcm.
diff --git a/drivers/peci/controller/Makefile b/drivers/peci/controller/Makefile
index 022c28ef1bf0..e247449bb423 100644
--- a/drivers/peci/controller/Makefile
+++ b/drivers/peci/controller/Makefile
@@ -1,3 +1,4 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o
+obj-$(CONFIG_PECI_NPCM) += peci-npcm.o
diff --git a/drivers/peci/controller/peci-npcm.c b/drivers/peci/controller/peci-npcm.c
new file mode 100644
index 000000000000..ec613d35c796
--- /dev/null
+++ b/drivers/peci/controller/peci-npcm.c
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Nuvoton Technology corporation
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/peci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* NPCM GCR module */
+#define NPCM_INTCR3_OFFSET 0x9C
+#define NPCM_INTCR3_PECIVSEL BIT(19)
+
+/* NPCM PECI Registers */
+#define NPCM_PECI_CTL_STS 0x00
+#define NPCM_PECI_RD_LENGTH 0x04
+#define NPCM_PECI_ADDR 0x08
+#define NPCM_PECI_CMD 0x0C
+#define NPCM_PECI_CTL2 0x10
+#define NPCM_PECI_WR_LENGTH 0x1C
+#define NPCM_PECI_PDDR 0x2C
+#define NPCM_PECI_DAT_INOUT(n) (0x100 + ((n) * 4))
+
+#define NPCM_PECI_MAX_REG 0x200
+
+/* NPCM_PECI_CTL_STS - 0x00 : Control Register */
+#define NPCM_PECI_CTRL_DONE_INT_EN BIT(6)
+#define NPCM_PECI_CTRL_ABRT_ERR BIT(4)
+#define NPCM_PECI_CTRL_CRC_ERR BIT(3)
+#define NPCM_PECI_CTRL_DONE BIT(1)
+#define NPCM_PECI_CTRL_START_BUSY BIT(0)
+
+/* NPCM_PECI_RD_LENGTH - 0x04 : Command Register */
+#define NPCM_PECI_RD_LEN_MASK GENMASK(6, 0)
+
+/* NPCM_PECI_CMD - 0x10 : Command Register */
+#define NPCM_PECI_CTL2_MASK GENMASK(7, 6)
+
+/* NPCM_PECI_WR_LENGTH - 0x1C : Command Register */
+#define NPCM_PECI_WR_LEN_MASK GENMASK(6, 0)
+
+/* NPCM_PECI_PDDR - 0x2C : Command Register */
+#define NPCM_PECI_PDDR_MASK GENMASK(4, 0)
+
+#define NPCM_PECI_INT_MASK (NPCM_PECI_CTRL_ABRT_ERR | \
+ NPCM_PECI_CTRL_CRC_ERR | \
+ NPCM_PECI_CTRL_DONE)
+
+#define NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC (50 * USEC_PER_MSEC)
+#define NPCM_PECI_IDLE_CHECK_INTERVAL_USEC (10 * USEC_PER_MSEC)
+#define NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT 1000
+#define NPCM_PECI_CMD_TIMEOUT_MS_MAX 60000
+#define NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT 15
+#define NPCM_PECI_PULL_DOWN_DEFAULT 0
+
+struct npcm_peci {
+ u32 cmd_timeout_ms;
+ struct completion xfer_complete;
+ struct regmap *regmap;
+ u32 status;
+ spinlock_t lock; /* to sync completion status handling */
+ struct peci_controller *controller;
+ struct device *dev;
+ struct clk *clk;
+ int irq;
+};
+
+static int npcm_peci_xfer(struct peci_controller *controller, u8 addr, struct peci_request *req)
+{
+ struct npcm_peci *priv = dev_get_drvdata(controller->dev.parent);
+ unsigned long timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
+ unsigned int msg_rd;
+ u32 cmd_sts;
+ int i, ret;
+
+ /* Check command sts and bus idle state */
+ ret = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+ !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+ NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+ NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+ if (ret)
+ return ret; /* -ETIMEDOUT */
+
+ spin_lock_irq(&priv->lock);
+ reinit_completion(&priv->xfer_complete);
+
+ regmap_write(priv->regmap, NPCM_PECI_ADDR, addr);
+ regmap_write(priv->regmap, NPCM_PECI_RD_LENGTH, NPCM_PECI_WR_LEN_MASK & req->rx.len);
+ regmap_write(priv->regmap, NPCM_PECI_WR_LENGTH, NPCM_PECI_WR_LEN_MASK & req->tx.len);
+
+ if (req->tx.len) {
+ regmap_write(priv->regmap, NPCM_PECI_CMD, req->tx.buf[0]);
+
+ for (i = 0; i < (req->tx.len - 1); i++)
+ regmap_write(priv->regmap, NPCM_PECI_DAT_INOUT(i), req->tx.buf[i + 1]);
+ }
+
+#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG)
+ dev_dbg(priv->dev, "addr : %#02x, tx.len : %#02x, rx.len : %#02x\n",
+ addr, req->tx.len, req->rx.len);
+ print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req->tx.len);
+#endif
+
+ priv->status = 0;
+ regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_CTRL_START_BUSY,
+ NPCM_PECI_CTRL_START_BUSY);
+
+ spin_unlock_irq(&priv->lock);
+
+ ret = wait_for_completion_interruptible_timeout(&priv->xfer_complete, timeout);
+ if (ret < 0)
+ return ret;
+
+ if (ret == 0) {
+ dev_dbg(priv->dev, "timeout waiting for a response\n");
+ return -ETIMEDOUT;
+ }
+
+ spin_lock_irq(&priv->lock);
+
+ if (priv->status != NPCM_PECI_CTRL_DONE) {
+ spin_unlock_irq(&priv->lock);
+ dev_dbg(priv->dev, "no valid response, status: %#02x\n", priv->status);
+ return -EIO;
+ }
+
+ regmap_write(priv->regmap, NPCM_PECI_CMD, 0);
+
+ for (i = 0; i < req->rx.len; i++) {
+ regmap_read(priv->regmap, NPCM_PECI_DAT_INOUT(i), &msg_rd);
+ req->rx.buf[i] = (u8)msg_rd;
+ }
+
+ spin_unlock_irq(&priv->lock);
+
+#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG)
+ print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req->rx.len);
+#endif
+ return 0;
+}
+
+static irqreturn_t npcm_peci_irq_handler(int irq, void *arg)
+{
+ struct npcm_peci *priv = arg;
+ u32 status_ack = 0;
+ u32 status;
+
+ spin_lock(&priv->lock);
+ regmap_read(priv->regmap, NPCM_PECI_CTL_STS, &status);
+ priv->status |= (status & NPCM_PECI_INT_MASK);
+
+ if (status & NPCM_PECI_CTRL_CRC_ERR)
+ status_ack |= NPCM_PECI_CTRL_CRC_ERR;
+
+ if (status & NPCM_PECI_CTRL_ABRT_ERR)
+ status_ack |= NPCM_PECI_CTRL_ABRT_ERR;
+
+ /*
+ * All commands should be ended up with a NPCM_PECI_CTRL_DONE
+ * bit set even in an error case.
+ */
+ if (status & NPCM_PECI_CTRL_DONE) {
+ status_ack |= NPCM_PECI_CTRL_DONE;
+ complete(&priv->xfer_complete);
+ }
+
+ regmap_write_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_INT_MASK, status_ack);
+
+ spin_unlock(&priv->lock);
+ return IRQ_HANDLED;
+}
+
+static int npcm_peci_init_ctrl(struct npcm_peci *priv)
+{
+ u32 cmd_sts;
+ int ret;
+
+ priv->clk = devm_clk_get_enabled(priv->dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ dev_err(priv->dev, "failed to get ref clock\n");
+ return PTR_ERR(priv->clk);
+ }
+
+ ret = device_property_read_u32(priv->dev, "cmd-timeout-ms", &priv->cmd_timeout_ms);
+ if (ret) {
+ priv->cmd_timeout_ms = NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT;
+ } else if (priv->cmd_timeout_ms > NPCM_PECI_CMD_TIMEOUT_MS_MAX ||
+ priv->cmd_timeout_ms == 0) {
+ dev_warn(priv->dev, "invalid cmd-timeout-ms: %u, falling back to: %u\n",
+ priv->cmd_timeout_ms, NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT);
+
+ priv->cmd_timeout_ms = NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT;
+ }
+
+ regmap_update_bits(priv->regmap, NPCM_PECI_CTL2, NPCM_PECI_CTL2_MASK,
+ NPCM_PECI_PULL_DOWN_DEFAULT << 6);
+
+ regmap_update_bits(priv->regmap, NPCM_PECI_PDDR, NPCM_PECI_PDDR_MASK,
+ NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT);
+
+ ret = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+ !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+ NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+ NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+ if (ret)
+ return ret; /* -ETIMEDOUT */
+
+ /* PECI interrupt enable */
+ regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_CTRL_DONE_INT_EN,
+ NPCM_PECI_CTRL_DONE_INT_EN);
+
+ return 0;
+}
+
+static const struct regmap_config npcm_peci_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = NPCM_PECI_MAX_REG,
+ .fast_io = true,
+};
+
+static struct peci_controller_ops npcm_ops = {
+ .xfer = npcm_peci_xfer,
+};
+
+static int npcm_peci_probe(struct platform_device *pdev)
+{
+ struct peci_controller *controller;
+ struct npcm_peci *priv;
+ void __iomem *base;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = &pdev->dev;
+ dev_set_drvdata(&pdev->dev, priv);
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ priv->regmap = devm_regmap_init_mmio(&pdev->dev, base, &npcm_peci_regmap_config);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq < 0)
+ return priv->irq;
+
+ ret = devm_request_irq(&pdev->dev, priv->irq, npcm_peci_irq_handler,
+ 0, "peci-npcm-irq", priv);
+ if (ret)
+ return ret;
+
+ init_completion(&priv->xfer_complete);
+ spin_lock_init(&priv->lock);
+
+ ret = npcm_peci_init_ctrl(priv);
+ if (ret)
+ return ret;
+
+ controller = devm_peci_controller_add(priv->dev, &npcm_ops);
+ if (IS_ERR(controller))
+ return dev_err_probe(priv->dev, PTR_ERR(controller),
+ "failed to add npcm peci controller\n");
+
+ priv->controller = controller;
+
+ return 0;
+}
+
+static const struct of_device_id npcm_peci_of_table[] = {
+ { .compatible = "nuvoton,npcm750-peci", },
+ { .compatible = "nuvoton,npcm845-peci", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, npcm_peci_of_table);
+
+static struct platform_driver npcm_peci_driver = {
+ .probe = npcm_peci_probe,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = npcm_peci_of_table,
+ },
+};
+module_platform_driver(npcm_peci_driver);
+
+MODULE_AUTHOR("Tomer Maimon <tomer.maimon at nuvoton.com>");
+MODULE_DESCRIPTION("NPCM PECI driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PECI);
--
2.33.0
More information about the openbmc
mailing list