[PATCH v5 4/9] dt-bindings: pinctrl: Add Nuvoton WPCM450
Jonathan Neuschäfer
j.neuschaefer at gmx.net
Sat Jan 29 22:52:23 AEDT 2022
This binding is heavily based on the one for NPCM7xx, because the
hardware is similar. There are some notable differences, however:
- The addresses of GPIO banks are not physical addresses but simple
indices (0 to 7), because the GPIO registers are not laid out in
convenient blocks.
- Pinmux settings can explicitly specify that the GPIO mode is used.
Certain pins support blink patterns in hardware. This is currently not
modelled in the DT binding.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer at gmx.net>
Reviewed-by: Rob Herring <robh at kernel.org>
---
v5:
- Add Rob's R-b
v4:
- Small improvements around gpio node addresses, suggested by Rob Herring
v3:
- https://lore.kernel.org/lkml/20211224200935.93817-5-j.neuschaefer@gmx.net/
- Make changes suggested by Rob Herring
- Fix lint errors
- Simplify child node patterns
- Remove if/type=object/then trick
- Reduce interrupts.maxItems to 3: 4 aren't necessary
- Replace list of gpio0/1/2/etc. with pattern
- Remove nuvoton,interrupt-map again, to simplify the binding
- Make tuples clearer
v2:
- https://lore.kernel.org/lkml/20211207210823.1975632-5-j.neuschaefer@gmx.net/
- Move GPIO into subnodes
- Improve use of quotes
- Remove unnecessary minItems/maxItems lines
- Remove "phandle: true"
- Use separate prefixes for pinmux and pincfg nodes
- Add nuvoton,interrupt-map property
- Make it possible to set pinmux to GPIO explicitly
v1:
- https://lore.kernel.org/lkml/20210602120329.2444672-5-j.neuschaefer@gmx.net/
---
.../pinctrl/nuvoton,wpcm450-pinctrl.yaml | 160 ++++++++++++++++++
1 file changed, 160 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
new file mode 100644
index 0000000000000..47a56b83a610d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/nuvoton,wpcm450-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton WPCM450 pin control and GPIO
+
+maintainers:
+ - Jonathan Neuschäfer <j.neuschaefer at gmx.net>
+
+properties:
+ compatible:
+ const: nuvoton,wpcm450-pinctrl
+
+ reg:
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+patternProperties:
+ # There are three kinds of subnodes:
+ # 1. a GPIO controller node for each GPIO bank
+ # 2. a pinmux node configures pin muxing for a group of pins (e.g. rmii2)
+ # 3. a pinconf node configures properties of a single pin
+
+ "^gpio@[0-7]$":
+ type: object
+
+ description:
+ Eight GPIO banks (gpio at 0 to gpio at 7), that each contain between 14 and 18
+ GPIOs. Some GPIOs support interrupts.
+
+ properties:
+ reg:
+ minimum: 0
+ maximum: 7
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 2
+
+ interrupts:
+ maxItems: 3
+ description:
+ The interrupts associated with this GPIO bank
+
+ required:
+ - reg
+ - gpio-controller
+ - '#gpio-cells'
+
+ "^mux-":
+ $ref: pinmux-node.yaml#
+
+ properties:
+ groups:
+ description:
+ One or more groups of pins to mux to a certain function
+ items:
+ enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp,
+ hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo,
+ clko, smi, uinc, gspi, mben, xcs2, xcs1, sdio, sspi, fi0,
+ fi1, fi2, fi3, fi4, fi5, fi6, fi7, fi8, fi9, fi10, fi11,
+ fi12, fi13, fi14, fi15, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5,
+ pwm6, pwm7, hg0, hg1, hg2, hg3, hg4, hg5, hg6, hg7 ]
+ function:
+ description:
+ The function that a group of pins is muxed to
+ enum: [ smb3, smb4, smb5, scs1, scs2, scs3, smb0, smb1, smb2, bsp,
+ hsp1, hsp2, r1err, r1md, rmii2, r2err, r2md, kbcc, dvo0,
+ dvo1, dvo2, dvo3, dvo4, dvo5, dvo6, dvo7, clko, smi, uinc,
+ gspi, mben, xcs2, xcs1, sdio, sspi, fi0, fi1, fi2, fi3, fi4,
+ fi5, fi6, fi7, fi8, fi9, fi10, fi11, fi12, fi13, fi14, fi15,
+ pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, pwm6, pwm7, hg0, hg1,
+ hg2, hg3, hg4, hg5, hg6, hg7, gpio ]
+
+ dependencies:
+ groups: [ function ]
+ function: [ groups ]
+
+ additionalProperties: false
+
+ "^cfg-":
+ $ref: pincfg-node.yaml#
+
+ properties:
+ pins:
+ description:
+ A list of pins to configure in certain ways, such as enabling
+ debouncing
+ items:
+ pattern: "^gpio1?[0-9]{1,2}$"
+
+ input-debounce: true
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ pinctrl: pinctrl at b8003000 {
+ compatible = "nuvoton,wpcm450-pinctrl";
+ reg = <0xb8003000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio0: gpio at 0 {
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
+ <3 IRQ_TYPE_LEVEL_HIGH>,
+ <4 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ mux-rmii2 {
+ groups = "rmii2";
+ function = "rmii2";
+ };
+
+ pinmux_uid: mux-uid {
+ groups = "gspi", "sspi";
+ function = "gpio";
+ };
+
+ pinctrl_uid: cfg-uid {
+ pins = "gpio14";
+ input-debounce = <1>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uid>, <&pinmux_uid>;
+
+ uid {
+ label = "UID";
+ linux,code = <102>;
+ gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
--
2.34.1
More information about the openbmc
mailing list