[PATCH linux dev-6.0] pmbus: Add mp2971/mp2973 support in mp2975
Wang Xiaohua
wangxiaohua.1217 at bytedance.com
Thu Dec 8 19:22:39 AEDT 2022
Add mp2971/mp2973 support in mp2975
Tested with:
My unit only include mp2971 and mp2973 devices
MP2973:
cat /sys/bus/i2c/devices/5-0076/hwmon/hwmon24/*label
iin
iout1
iout2
vin
vout1
vout2
pin
pout1
pout2
cat /sys/bus/i2c/devices/5-0076/hwmon/hwmon24/*input
0
82500
14000
12187
1787
1793
0
148000000
25000000
54000
MP2971:
cat /sys/bus/i2c/devices/5-0062/hwmon/hwmon20/*label
iin
iout1
iout2
vin
vout1
vout2
pin
pout1
pout2
cat /sys/bus/i2c/devices/5-0062/hwmon/hwmon20/*input
18500
22000
500
12187
1025
1800
226000000
22000000
1000000
55000
Signed-off-by: Wang Xiaohua <wangxiaohua.1217 at bytedance.com>
---
drivers/hwmon/pmbus/mp2975.c | 413 +++++++++++++++++++++++++++++++----
1 file changed, 372 insertions(+), 41 deletions(-)
diff --git a/drivers/hwmon/pmbus/mp2975.c b/drivers/hwmon/pmbus/mp2975.c
index 51986adfbf47..972b5b02dfdd 100644
--- a/drivers/hwmon/pmbus/mp2975.c
+++ b/drivers/hwmon/pmbus/mp2975.c
@@ -52,10 +52,33 @@
#define MP2975_MAX_PHASE_RAIL2 4
#define MP2975_PAGE_NUM 2
+#define MP2971_RAIL2_FUNC \
+ (PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | PMBUS_HAVE_IOUT | \
+ PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT)
+
#define MP2975_RAIL2_FUNC (PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT | \
PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | \
PMBUS_HAVE_POUT | PMBUS_PHASE_VIRTUAL)
+struct mp2971_device_info {
+ int max_phase_rail1;
+ int max_phase_rail2;
+ int imvp9_en_r1_mask;
+ int imvp9_en_r2_mask;
+};
+
+struct mp2971_data {
+ struct pmbus_driver_info info;
+ int vid_step[MP2975_PAGE_NUM];
+ int vout_format[MP2975_PAGE_NUM];
+ int vout_mode[MP2975_PAGE_NUM];
+ int vout_exponent[MP2975_PAGE_NUM];
+ int max_phase_rail1;
+ int max_phase_rail2;
+ int imvp9_en_r1_mask;
+ int imvp9_en_r2_mask;
+};
+
struct mp2975_data {
struct pmbus_driver_info info;
int vout_scale;
@@ -68,6 +91,9 @@ struct mp2975_data {
int curr_sense_gain[MP2975_PAGE_NUM];
};
+static const struct i2c_device_id mp2975_id[];
+
+#define to_mp2971_data(x) container_of(x, struct mp2971_data, info)
#define to_mp2975_data(x) container_of(x, struct mp2975_data, info)
static int mp2975_read_byte_data(struct i2c_client *client, int page, int reg)
@@ -95,6 +121,40 @@ mp2975_read_word_helper(struct i2c_client *client, int page, int phase, u8 reg,
return (ret > 0) ? ret & mask : ret;
}
+static int
+mp2971_linear2direct(struct mp2971_data *data, int page, int val)
+{
+ /* simple case */
+ if (val == 0)
+ return 0;
+
+ /* LINEAR16 does not support negative voltages */
+ if (val < 0)
+ return 0;
+
+ /*
+ * For a static exponents, we don't have a choice
+ * but to adjust the value to it.
+ */
+
+ if (data->vout_exponent[page] < 0)
+ val <<= -data->vout_exponent[page];
+ else
+ val >>= data->vout_exponent[page];
+ return clamp_val(val, 0, 0xffff);
+}
+
+static int
+mp2971_vid2direct(struct mp2971_data *data, int page, int val)
+{
+ int vrf = data->info.vrm_version[page];
+
+ if (vrf == imvp9)
+ return (val + 29) * data->vid_step[page];
+
+ return (val + 49) * data->vid_step[page];
+}
+
static int
mp2975_vid2direct(int vrf, int val)
{
@@ -214,6 +274,74 @@ mp2975_read_phases(struct i2c_client *client, struct mp2975_data *data,
return ret;
}
+static int
+mp2971_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp2971_data *data = to_mp2971_data(info);
+ int ret;
+
+ switch (reg) {
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ case PMBUS_READ_IOUT:
+ ret = mp2975_read_word_helper(client, page, phase,
+ reg, GENMASK(15, 0));
+ break;
+ case PMBUS_READ_VOUT:
+ ret = mp2975_read_word_helper(client, page, phase, reg,
+ GENMASK(11, 0));
+ if (ret < 0)
+ return ret;
+ /*
+ * READ_VOUT can be provided in VID or direct format. The
+ * format type is specified by bit 15 of the register
+ * MP2971_MFR_DC_LOOP_CTRL. The driver enforces VOUT direct
+ * format, since device allows to set the different formats for
+ * the different rails and also all VOUT limits registers are
+ * provided in a direct format. In case format is VID - convert
+ * to direct.
+ */
+ switch (data->vout_format[page]) {
+ case linear:
+ ret = mp2971_linear2direct(data, page, ret);
+ break;
+ case vid:
+ ret = mp2971_vid2direct(data, page, ret);
+ break;
+ case direct:
+ break;
+ default:
+ return -ENODATA;
+ }
+ break;
+ case PMBUS_UT_WARN_LIMIT:
+ case PMBUS_UT_FAULT_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_VOUT_UV_WARN_LIMIT:
+ case PMBUS_VOUT_OV_WARN_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_IIN_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_LV_FAULT_LIMIT:
+ case PMBUS_IIN_OC_WARN_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_UC_FAULT_LIMIT:
+ case PMBUS_POUT_OP_FAULT_LIMIT:
+ case PMBUS_POUT_OP_WARN_LIMIT:
+ case PMBUS_PIN_OP_WARN_LIMIT:
+ return -ENXIO;
+ default:
+ return -ENODATA;
+ }
+
+ return ret;
+}
+
static int mp2975_read_word_data(struct i2c_client *client, int page,
int phase, int reg)
{
@@ -365,6 +493,63 @@ mp2975_set_phase_rail2(struct pmbus_driver_info *info, int num_phases)
info->pfunc[MP2975_MAX_PHASE_RAIL1 - i] = PMBUS_HAVE_IOUT;
}
+static int mp2971_identify_multiphase(struct i2c_client *client,
+ struct mp2971_data *data,
+ struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify multiphase for rail 1 - could be from 1 to 12. */
+ ret = i2c_smbus_read_word_data(client, MP2975_MFR_VR_MULTI_CONFIG_R1);
+ if (ret <= 0)
+ return ret;
+
+ info->phases[0] = ret & GENMASK(3, 0);
+
+ /*
+ * The device provides a total of 8 PWM pins, and can be configured
+ * to different phase count applications for rail 1 and rail 2.
+ * Rail 1 can be set to 8 phases, while rail 2 can only be set to 4
+ * phases at most. When rail 1’s phase count is configured as 0, rail
+ * 1 operates with 1-phase DCM. When rail 2 phase count is configured
+ * as 0, rail 2 is disabled.
+ */
+ if (info->phases[0] > data->max_phase_rail1)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int
+mp2971_identify_vid(struct i2c_client *client, struct mp2971_data *data,
+ struct pmbus_driver_info *info, u32 reg, int page,
+ u32 imvp_bit, u32 vr_bit)
+{
+ int ret;
+
+ /* Identify VID mode and step selection. */
+ ret = i2c_smbus_read_word_data(client, reg);
+ if (ret < 0)
+ return ret;
+
+ if (ret & imvp_bit) {
+ info->vrm_version[page] = imvp9;
+ data->vid_step[page] = MP2975_PROT_DEV_OV_OFF;
+ } else if (ret & vr_bit) {
+ info->vrm_version[page] = vr12;
+ data->vid_step[page] = MP2975_PROT_DEV_OV_ON;
+ } else {
+ info->vrm_version[page] = vr13;
+ data->vid_step[page] = MP2975_PROT_DEV_OV_OFF;
+ }
+
+ return 0;
+}
+
static int
mp2975_identify_multiphase(struct i2c_client *client, struct mp2975_data *data,
struct pmbus_driver_info *info)
@@ -428,6 +613,68 @@ mp2975_identify_vid(struct i2c_client *client, struct mp2975_data *data,
return 0;
}
+static int
+mp2971_identify_rails_vid(struct i2c_client *client, struct mp2971_data *data,
+ struct pmbus_driver_info *info)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, 2);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 1. */
+ ret = mp2971_identify_vid(client, data, info,
+ MP2975_MFR_VR_MULTI_CONFIG_R1, 0,
+ data->imvp9_en_r1_mask,
+ MP2975_VID_STEP_SEL_R1);
+ if (ret < 0)
+ return ret;
+
+ /* Identify VID mode for rail 2, if connected. */
+ if (info->phases[1])
+ ret = mp2971_identify_vid(client, data, info,
+ MP2975_MFR_VR_MULTI_CONFIG_R2, 1,
+ data->imvp9_en_r2_mask,
+ MP2975_VID_STEP_SEL_R2);
+ return ret;
+}
+
+static int mp2971_identify_vout_format(struct i2c_client *client,
+ struct mp2971_data *data,
+ struct pmbus_driver_info *info)
+{
+ int i, ret, vout_mode;
+
+ for (i = 0; i < info->pages; i++) {
+ ret = i2c_smbus_write_byte_data(client, PMBUS_PAGE, i);
+ if (ret < 0)
+ return ret;
+
+ ret = i2c_smbus_read_byte_data(client, PMBUS_VOUT_MODE);
+ if (ret < 0)
+ return ret;
+
+ vout_mode = ret;
+
+ switch (vout_mode >> 5) {
+ case 0:
+ data->vout_format[i] = linear;
+ data->vout_exponent[i] = ((s8)(vout_mode << 3)) >> 3;
+ break;
+ case 1:
+ data->vout_format[i] = vid;
+ break;
+ case 2:
+ data->vout_format[i] = direct;
+ break;
+ default:
+ return -ENODEV;
+ }
+ }
+ return 0;
+}
+
static int
mp2975_identify_rails_vid(struct i2c_client *client, struct mp2975_data *data,
struct pmbus_driver_info *info)
@@ -659,6 +906,24 @@ mp2975_vout_per_rail_config_get(struct i2c_client *client,
return 0;
}
+static struct pmbus_driver_info mp2971_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = linear,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .format[PSC_TEMPERATURE] = linear,
+ .format[PSC_CURRENT_IN] = linear,
+ .format[PSC_CURRENT_OUT] = linear,
+ .format[PSC_POWER] = linear,
+ .m[PSC_VOLTAGE_OUT] = 1,
+ .R[PSC_VOLTAGE_OUT] = 3,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_IIN | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_POUT |
+ PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT,
+ .read_byte_data = mp2975_read_byte_data,
+ .read_word_data = mp2971_read_word_data,
+};
+
static struct pmbus_driver_info mp2975_info = {
.pages = 1,
.format[PSC_VOLTAGE_IN] = linear,
@@ -683,63 +948,129 @@ static struct pmbus_driver_info mp2975_info = {
static int mp2975_probe(struct i2c_client *client)
{
struct pmbus_driver_info *info;
- struct mp2975_data *data;
int ret;
+ char *name;
+
+ name = (int)i2c_match_id(mp2975_id, client)->name;
+ if (name == NULL)
+ return 0;
+ if (!strcmp(name, "mp2971") || !strcmp(name, "mp2973")) {
+ struct mp2971_data *data;
+ struct mp2971_device_info *device_info;
+
+ data = devm_kzalloc(&client->dev, sizeof(struct mp2971_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ device_info =
+ (struct mp2971_device_info *)i2c_match_id(mp2975_id, client)
+ ->driver_data;
+
+ memcpy(&data->info, &mp2971_info, sizeof(*info));
+ info = &data->info;
+
+ if (device_info) {
+ data->imvp9_en_r1_mask = device_info->imvp9_en_r1_mask;
+ data->imvp9_en_r2_mask = device_info->imvp9_en_r2_mask;
+ data->max_phase_rail1 = device_info->max_phase_rail1;
+ data->max_phase_rail2 = device_info->max_phase_rail2;
+ }
- data = devm_kzalloc(&client->dev, sizeof(struct mp2975_data),
- GFP_KERNEL);
- if (!data)
- return -ENOMEM;
+ /* Identify multiphase configuration for rail 2. */
+ ret = mp2975_identify_multiphase_rail2(client);
+ if (ret < 0)
+ return ret;
- memcpy(&data->info, &mp2975_info, sizeof(*info));
- info = &data->info;
+ if (ret) {
+ /* Two rails are connected. */
+ data->info.pages = MP2975_PAGE_NUM;
+ data->info.phases[1] = ret;
+ data->info.func[1] = MP2971_RAIL2_FUNC;
+ }
- /* Identify multiphase configuration for rail 2. */
- ret = mp2975_identify_multiphase_rail2(client);
- if (ret < 0)
- return ret;
+ /* Identify multiphase configuration. */
+ ret = mp2971_identify_multiphase(client, data, info);
+ if (ret)
+ return ret;
- if (ret) {
- /* Two rails are connected. */
- data->info.pages = MP2975_PAGE_NUM;
- data->info.phases[1] = ret;
- data->info.func[1] = MP2975_RAIL2_FUNC;
- }
+ /* Identify VID setting per rail. */
+ ret = mp2971_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
- /* Identify multiphase configuration. */
- ret = mp2975_identify_multiphase(client, data, info);
- if (ret)
- return ret;
+ /* Identify vout format. */
+ ret = mp2971_identify_vout_format(client, data, info);
+ if (ret < 0)
+ return ret;
- /* Identify VID setting per rail. */
- ret = mp2975_identify_rails_vid(client, data, info);
- if (ret < 0)
- return ret;
+ } else {
+ struct mp2975_data *data;
- /* Obtain current sense gain of power stage. */
- ret = mp2975_current_sense_gain_get(client, data);
- if (ret)
- return ret;
+ data = devm_kzalloc(&client->dev, sizeof(struct mp2975_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
- /* Obtain voltage reference values. */
- ret = mp2975_vref_get(client, data, info);
- if (ret)
- return ret;
+ memcpy(&data->info, &mp2975_info, sizeof(*info));
+ info = &data->info;
- /* Obtain vout over-voltage scales. */
- ret = mp2975_vout_ov_scale_get(client, data, info);
- if (ret < 0)
- return ret;
+ /* Identify multiphase configuration for rail 2. */
+ ret = mp2975_identify_multiphase_rail2(client);
+ if (ret < 0)
+ return ret;
- /* Obtain offsets, maximum and format for vout. */
- ret = mp2975_vout_per_rail_config_get(client, data, info);
- if (ret)
- return ret;
+ if (ret) {
+ /* Two rails are connected. */
+ data->info.pages = MP2975_PAGE_NUM;
+ data->info.phases[1] = ret;
+ data->info.func[1] = MP2975_RAIL2_FUNC;
+ }
+
+ /* Identify multiphase configuration. */
+ ret = mp2975_identify_multiphase(client, data, info);
+ if (ret)
+ return ret;
+
+ /* Identify VID setting per rail. */
+ ret = mp2975_identify_rails_vid(client, data, info);
+ if (ret < 0)
+ return ret;
+
+ /* Obtain current sense gain of power stage. */
+ ret = mp2975_current_sense_gain_get(client, data);
+ if (ret)
+ return ret;
+
+ /* Obtain voltage reference values. */
+ ret = mp2975_vref_get(client, data, info);
+ if (ret)
+ return ret;
+
+ /* Obtain vout over-voltage scales. */
+ ret = mp2975_vout_ov_scale_get(client, data, info);
+ if (ret < 0)
+ return ret;
+
+ /* Obtain offsets, maximum and format for vout. */
+ ret = mp2975_vout_per_rail_config_get(client, data, info);
+ if (ret)
+ return ret;
+ }
return pmbus_do_probe(client, info);
}
+static const struct mp2971_device_info mp2971_device_info = {
+ .imvp9_en_r1_mask = BIT(14),
+ .imvp9_en_r2_mask = BIT(13),
+ .max_phase_rail1 = 8,
+ .max_phase_rail2 = 4,
+};
+
static const struct i2c_device_id mp2975_id[] = {
+ {"mp2971", (kernel_ulong_t)&mp2971_device_info },
+ {"mp2973", (kernel_ulong_t)&mp2971_device_info },
{"mp2975", 0},
{}
};
--
2.25.1
More information about the openbmc
mailing list